dji PP1012023 Osmo Pocket 3 Creator Combo User Guide

June 1, 2024
DJi

dji PP1012023 Osmo Pocket 3 Creator Combo User Guide
dji PP1012023 Osmo Pocket 3 Creator Combo

Download DJI Mimo App

The DJI Mimo app is required when using Osmo Pocket 3. Search for “DJI Mimo” in the mobile app store or scan the QR code with your mobile phone to download and install the DJI Mimo app.

Introduction

Introduction

  1. Roll Motor
  2. Rotatable Touchscreen
  3. Status LED
  4. 5D Joystick
  5. Title Motor
  6. Pan Motor
  7. Loudspeaker
  8. Shutter/Record Button
  9. Lanyard Hole
  10. Quick-Release Slot I
  11. USB-C Port
  12. Camera
  13. MicroSD Card Slot
  14. Quick-Release Slot II
  15. Microphone

Button Features

Button Features

Shutter/Record Button

  • Press once: power on, take photos or record
  • Press and hold: power off

5D Joystick

  • Push stick: control gimbal direction or zoom
  • Press once: back
  • Press and hold: lock gimbal
  • Double press: recenter gimbal
  • Triple press: rotate gimbal

Operating the Rotatable Touchscreen

Rotate the touchscreen to Power On

Rotate the touchscreen to the left to power on Osmo Pocket 3, and rotate the touchscreen to the right to power off.
Operating the Rotatable Touchscreen

Tap or Swipe on the Touchscreen
After Osmo Pocket 3 is powered on, the touchscreen displays the live view as well as the microSD card information, battery level and shooting mode. Tap or swipe on a touchscreen to interact with the Osmo Pocket 3.

Inserting the MicroSD Card

The footage shot on Osmo Pocket 3 is stored on a microSD card. A UHS-I Speed Grade 3 rating microSD card is required due to the fast read and write speeds necessary for high resolution video data.

Charging Osmo Pocket 3

Connect a USB-C charger (not included) to the USB-C port using the Type-C to Type-C PD cable (included). It is recommended to use the DJI 30 W USB-C Charger or a USB-C charger that supports Power Delivery.

Accessories

Osmo Pocket 3 Battery Handle
The built-in battery within the Osmo Pocket 3 battery handle has a capacity of 1000mAh.
Connect the handle with Osmo Pocket 3 via the USB-C port, which can get more out of the camera.

Osmo Pocket 3 Handle With 1/4″ Thread
Attach the Osmo Pocket 3 handle with 1/4″ thread to Osmo Pocket 3 via the USB-C port. With attached, Osmo Pocket 3 is more comfortable to hold.

Osmo Pocket 3 Wide-Angle Lens
With magnetic design, the Osmo Pocket 3 wide-angel lens can be easily mounted the camera. When mounted, the camera can get a wider FOV and capture more within the frame.

Specifications

Model PP-101
Compatible DJI Charger DJI 30 W USB-C Charger
Operating Temperature 0° to 40° C (32° to 104° F)

Wi-Fi
Wi-Fi Protocol| 802.11 a/b/g/n/ac
Wi-Fi Operating Frequency| 2.4000-2.4835 GHz, 5.150-5.250 GHz, 5.725-5.850 GHz
Wi-Fi Transmission Power (EIRP)| 2.4 GHz: < 23 dBm (FCC), < 20 dBm (CE/SRRC/MIC) 5.1 GHz: <23 dBm (FCC/SRRC), <20 dBm (CE) 5.8 GHz: <23 dBm (FCC/SRRC), <14 dBm (CE)
Bluetooth
Bluetooth Protocol| BR/EDR,BLE
Bluetooth Operating Frequency| 2.4GHz-2.4835GHz
Bluetooth Transmission Power (EIRP)| <14 dBm

FCC Compliance Notice

Supplier’s Declaration of Conformity.
Product name: Osmo Pocket 3
Model Number: PP-101
Responsible Party: DJI Research LLC
Responsible Party Address: 435 Portage Ave, Palo Alto, CA 94306
Website: www.dji.com
We, DJI Research LLC, being the responsible party, declares that the above mentioned model was tested to demonstrate complying with all applicable FCC rules and regulations.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Information

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA).

These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the body at least 10mm separation distance. This device was tested for typical body-worn operations with the back of the handset kept 10mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10mm separation distance between the user’s body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements and should be avoided.

These requirements set a SAR limit of 4 W/kg averaged over ten gram of tissue. The highest SAR value reported under this standard during product certification for use when properly worn on the limbs.

ISED Compliance Notice

CAN ICES-003 (B) / NMB-003(B)
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1)This device may not cause interference.(2)This device must accept any interference, including interference that may cause undesired operation of the device.

This equipment complies with RSS-102 radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.The portable device is designed to meet the requirements for exposure to radio waves established by the CNR-102.

These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value  reported under this standard during product certification for use when properly worn on the body at least 10mm separation distance. This device was tested for typical body-worn operations with the back of the handset kept 10mm from the body. To maintain compliance with RF exposure requirements, use accessories that maintain a 10mm separation distance between the user’s body and the back of the handset. The use of belt clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with RF exposure requirements and should be avoided.

The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.


5150-5250MHz

CMIIT ID: 2 023AP7955
KC Compliance Notice

NCC Compliance Notice

EU & UK Compliance Notice

Symbols
EU Compliance Statement: SZ DJI Osmo Technology Co., Ltd. hereby declares that this device (Osmo Pocket 3) is in compliance with the essential requirements and other relevant provisions of the Directive 2014/53/EU.
A copy of the EU Declaration of Conformity is available online at www.dji.com /euro-compliance EU contact address: DJI GmbH, Industriestrasse 12, 97618, Niederlauer, Germany

GB Compliance Statement: SZ DJI Osmo Technology Co., Ltd. hereby declares that this device (Osmo Pocket 3) is in compliance with the essential requirements and other relevant provisions of Radio Equipment Regulations 2017.
A copy of the GB Declaration of Conformity is available online at www.dji.com /euro-compliance


Environmentally friendly disposal

Old electrical appliances must not be disposed of together with the residual waste, but have to be disposed of separately. The disposal at the communal collecting point via private persons is for free. The owner of old appliances is responsible to bring the appliances to these collecting points or to similar collection points. With this little personal effort, you contribute to recycle valuable raw materials and the treatment of toxic substances.

BE BG CZ DK DE EE
IE EL ES FR HR IT
CY LV LT LU HU MT
NL AT PL PT RO SI
SK FI SE UK(NI) TR NO
CH IS LI

W52: Indoor use only except for connection to 5.2GHz registered device.

To view the full compliance information, slide down on the camera view, tap the settings icon, and scroll through to select Compliance Info.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals