AEG NDP866PT Cooker Hood User Manual

AEG NDP866PT Cooker Hood

Connection

SAFETY INFORMATION AND INSTALLATION

WARNING!
Refer to the separate Installation Instructions booklet for Safety Information and Installation. Read carefully the Safety chapters before any use or maintenance of the appliance.

PRODUCT DESCRIPTION

Control panel overview

app‐ance returns to previous setting.
6| Maximum speed| The motor switches to maximum speed level. After 5 minutes the appliance returns to previous setting.
7| Breeze| The motor operates on the lowest speed. After 60 minutes the appliance turns off.
8| Hob²Hood| Indicator of the function to control hood from hob.
9| Filter notification| Reminds to change or clean the charcoal filter and clean the grease filter.
10| WiFi| Indicates WiFi connection status.
11| Light colour temperature| Changes the light colour temperature.
12| Lamp| Turns the lights on and off. Changes the light intensity.

DAILY USE

Using the hood

Check the recommended speed according to the table below.

1 While heating up food, cooking with covered pots.

2 While cooking with covered pots on multiple cooking zones or burners, gentle frying.

3 While boiling and frying big quantities of food without a lid, cooking on multiple cooking zones or burners

While boiling and frying big quantities of food without a lid, big humidity.

Refreshes the air in kitchen after cooking at a very low noise level. The function turns off au‐ to matically after 60 minutes. Use after cooking only.

It is recommended to leave the hood operating for approximately 15 minutes before and after cooking.

Activating the appliance

To operate the hood:

1. Pull out the drawer of the hood to switch on the control panel.
   You can now activate the functions.

2. To activate the function, touch the corresponding symbol.

If the fan speed is not set within one minute after switching on the hood, the control panel will deactivate. To activate it again, touch the symbol.

Deactivating the appliance

To turn off the appliance touch symbol again or close the hood drawer.

When the drawer is closed, the last fan speed setting will be saved. When the drawer is pulled out again, the hood will operate at the last selected fan speed.

Perfect Illumination – Lighting

The hood lighting works independently to other hood functions.

Activating and deactivating the lighting
To illuminate the cooking surface touch the symbol. Touch the  symbol again to change the light intensity in the following order: Maximum, Medium, Low, Off.
To switch off the lights, touch and hold the symbol for 3 seconds. Closing the drawer has no effect on the hood light.
Setting the light colour temperature

The hood remembers the last setting of the light intensity and colour temperature.
There are two ways to set the light colour temperature:

1. Touch the symbol to change the colour temperature from neutral, through warm to cold.
2. Touch and hold the  symbol to move smoothly between light colour temperatures.
   Release it once you reach the desired setting.

Aurora Tech

It is a function that automatically adjusts the illumination colour and intensity based on the time of day, creating an optimal ambiance.
Use the app to activate this function.

After activating from the app, the function will operate each time the lighting is switched on. You can still manually adjust the lighting settings using the and buttons. However, the Aurora Tech function will be deactivated.

Hob²Hood function

It is a function that connects the hob to a hood. Both the hob and the hood are equipped with an infrared signal communicator. The fan speed is determined based on the mode setting and the temperature of the hottest cookware on the hob. Alternatively, you can manually control the fan using the hob. This function can be activated from the hob’s control panel.

If the hood drawer is closed, the Hob²Hood will only activate the hood light. The fan will remain off.
If the drawer is open, the function will activate both the hood light and the fan.

For more information how to use the function, refer to the hob user manual.

Filter notification

Filter alarm reminds to change or clean the charcoal filter and clean the grease filter. The symbol blinks regularly for 30 seconds if the grease filter must be cleaned. The symbol blinks twice per every second for 30 seconds if the charcoal filter must be replaced.

This function activates independently after 40 hours of operation for grease filter and 160 hours of operation for charcoal filter.

Refer to Cleaning the grease filter in the Care and cleaning chapter.

Refer to Replacing the charcoal filter in the Care and cleaning chapter.

The function counter for charcoal filter is disabled by default. For recirculation mode, it must be activated.

To activate or deactivate the counter for charcoal filter:

1. Pull out the hood drawer.
2. Make sure the fan and the light are turned off.
3. Touch 2 symbol for 3 seconds.

The function is activated if symbol blinks once. The function is deactivated if symbol blinks twice.

To reset the function counter in the notification period:

1. Pull out the hood drawer.
2. Touch symbol for 3 seconds.
   The symbol stops blinking for the correct reset.

WiFi connectivity setup

This feature enables you to connect your appliance to a WiFi network and pair it with your mobile device. Using this feature, you can access additional functions, control and monitor your appliance from your mobile device, and receive notifications.

To connect the appliance you need:

• Wireless network with the Internet connection,
• Mobile device connected to your wireless network.

Installing the app

Take the following steps to connect the appliance to WiFi :

1. Make sure that the appliance is plugged into a power socket and turned on.
2. Make sure that your mobile device is connected to the same wireless network you want to add your appliance to.
3. To download the app, use your mobile device’s camera to scan the QR code located on the back cover of the user manual. You can also download the app directly from Google Play (Android) or App Store (iOS).
4. Open the app and register to create an account.

Configuring the appliance wireless connection

The onboarding is possible only for 20 seconds after activating the control panel. If the  symbol turns off, deactivate and activate the control panel again.

Follow the instructions in the app to complete the onboarding process:

1. Pull out the hood drawer. Make sure the fan and the lighting are turned off.
2. Touch and hold the symbol on your appliance for 3 seconds, the symbol starts to flash continuously. The onboarding process is ongoing.
3. Continue to follow the instructions in the app to complete the onboarding process.

To stop the onboarding process, touch the or any of the speed level symbols.

After the successful onboarding, the appliance emits a single beep, and the indicator stops flashing and becomes steady.
If the onboarding process is unsuccessful, the indicator flashes rapidly for 6 seconds and then turns off. Repeat the procedure.

If the onboarding process exceeds 1 minute, the control panel enters standby mode, the  indicator turns off, and the app provides feedback on the onboarding status.

After onboarding, the symbol is visible once the control panel is activated and a connection to the internet is established.

Each time the action is performed using the app, the indicator blinks 3 times.

Disabling / Enabling the appliance wireless connection

To temporarily disable the WiFi connection:

1. Pull out the hood drawer. Make sure the fan and the lighting are turned off.
2. Touch and hold the 1 symbol for 3 seconds until you hear a beep.

The 1 symbol blinks twice and the symbol turns off.

To enable the WiFi connection again:

1. Pull out the hood drawer. Make sure the fan and the lighting are turned off.
2. Touch and hold the 1 symbol for 3 seconds until you hear a beep.

The 1 symbol blinks once and the symbol turns on when the connection is estabilished.

Resetting the appliance wireless connection

To offboard the WiFi network:

1. Pull out the hood drawer. Make sure the fan and the lighting are turned off.
2. Touch and hold the symbol for 3 seconds.

The appliance emits a single beep, and the  symbol blinks until the successful reset. In some cases the symbol can blink only once.

This action results in the removal of the appliance from the WiFi network. To reestablish the connection, repeat all the steps described in the ‘Configuring the appliance wireless connection’ section.

CARE AND CLEANING

Notes on cleaning

Cleaning Agents

Do not use abrasive detergents and brushes.
Clean the surface of the appliance with a soft cloth with warm water and a mild detergent.

After cooking some parts of appliance can get hot. To avoid stains appliance must be cooled down and dried with clean cloth or paper towels.

Clean stains with a mild detergent.

Keep the hood clean

Clean the appliance and grease filters each month.
Clean the interior and grease filters carefully from fat.
Fat accumulation or other residue may cause fire.

Grease filters can be washed in a dishwasher.
The dishwasher must be set to a low temperature and a short cycle. The grease filter may discolour, it has no influence on the performance of the appliance.

Charcoal filter

The time of saturation of the charcoal filter varies de‐ pending on the type of cooking and the regularity of cleaning the grease filter. Refer to leaflet included in the accessory.

Before carrying out any maintenance, make sure there is no cookware on the hob and that the hood and the hob are disconnected from the power supply.

Cleaning the grease filter

Filters are mounted with the use of clips and pins on the opposite side.

To clean the filter:

1. Pull the cover to open it.
   

2. Pull the handle on the filter underneath the hood and slightly tilt the front of the filter down.
   

3. Clean the filters using a sponge with non abrasive detergents or in a dishwasher.
   The dishwasher must be set to a low temperature and a short cycle. The grease filter may discolour, it has no influence on the performance of the appliance

4. To mount the filters back follow the first two steps in reverse order.
   Repeat the steps for all filters if applicable.

Replacing the charcoal filter –   optional

Depending on type, filter can be or cannot be regenerated. Refer to the leaflet provided with the filter.

To replace the filter:

1. Remove the grease filters from the appliance.
   Refer to “Cleaning the grease filter” in this chapter.

2. Pull the tabs towards the bottom part of the filter.
   

3. Slightly tilt the front of the filter downwards, then pull.

4. To install a new filter, perform the steps in the following order.
   

Refer to the separate Installation Instructions booklet.

Replacing the lamp

This appliance is supplied with a LED lamp and separate control gear (LED driver).
These parts can be replaced by a technician only. In case of any malfunction refer to “Service” in the “Safety Instructions” chapter.

ENVIRONMENTAL CONCERNS

Recycle materials with the symbol . Put the packaging in relevant containers to recycle it.
Help protect the environment and human health by recycling waste of electrical and electronic appliances. Do not dispose of appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.

|
---|---
|

Customer Support

The software in this product contains components that are based on free and open source software. AEG gratefully acknowledges the contributions of the open software and robotics communities to the development project.
To access the source code of these free and open source software components whose license conditions require publishing, and to see their full copyright information and applicable license terms, please visit:
http://aeg.opensoftwarerepository.com (folder NIUS)

References

• home - osr
• Welcome to AEG

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>