ZAPCO HB CB20F DSP Amplifiers User Guide

: June 1, 2024
: ZAPCO

Table of Contents

ZAPCO HB CB20F DSP Amplifiers
Product Information
Product Usage Instructions
FAQ
HB CB20F Control Panel
Control LCD
Technical Specifications
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ZAPCO HB CB20F DSP Amplifiers

ZAPCO-HB-CB20F-DSP-Amplifiers-PRODUCT

Product Information

The HB CB20F is a DSP/amplifier from the ZAPCO Harmony Blue Note series. It features a control panel with various connections for power and grounding, as well as a display that shows the current voltage. ZAPCO emphasizes the importance of professional installation by authorized technicians to ensure proper setup and safety. Continuous exposure to high sound pressure levels can lead to hearing damage, so it’s advised to use common sense when adjusting volume levels.

Product Usage Instructions

Installation Guidelines

Installation should be done by professional technicians.
Place a fuse or circuit breaker within 18 inches of the battery.
Ensure the protection device is easily accessible.
Route wiring safely and correctly according to guidelines.

Mounting the Capacitor To mount your Zapco capacitor, follow these guidelines:

Ensure proper placement for easy access.
Follow recommended mounting procedures.

Volume Level Use common sense when adjusting volume levels to prevent hearing damage from excessive sound pressure levels.

FAQ

Q : Can the technical specifications change during production?
A : Yes, some features or specifications might be modified during production to enhance product performance.
Q : Where can I find updates for the product?
A: Updates are available on zapco.com. Ensure to check for any new information related to your product.

General Instructions

The installation of the product must be done by professional technicians. Always contact a ZAPCO Authorized Dealer.
Before you start your installation ZAPCO highly recommends that a fuse or circuit breaker be placed within 18″ of the battery. The protection device should be placed where it can be accessed easily and all wiring should be routed safely and correctly according to the following guidelines:

Do not run wiring close to hot or spinning objects
Always use wire grommets when routing wire through the firewall or any other metal panels
Make sure that the potential for pinched wiring is avoided by routing all wires away from moving objects, including brake, gas and clutch pedals, etc.

Planning your power connections

The +12V B is the main power input. This must be connected the vehicle battery’s positive (+) terminal
The GND is the main ground or negative connection. This must be securely attached to bare metal at the vehicle frame
The terminal between the main power and ground is the + 12 turn-on input (REM) and can be connected to the head unit turn-on output wire. If none is available, it can be connected to an accessory (ACC) terminal

Mounting your capacitor
Mounting your Zapco capacitor is easy. Just keep in mind a few guidelines:

The capacitor requires adequate ventilation. Creating power creates heat, and cooling requires air
Keep the capacitor out of the engine compartment or other locations that may cause excessive heat or moisture
Do not mount the capacitor to a subwoofer box or other place that may have excessive vibration

Continuous exposure to excessive sound pressure levels may cause hearing damage. ZAPCO strongly advises that you use common sense when setting volume levels. Everything written in this manual is for the proper use of the products. Some features or specifications could be modified during production to improve the product performance. The technical speci˜cations and functionalities stated here are current as of the time of publication.

HB CB20F Control Panel

ZAPCO-HB-CB20F-DSP-Amplifiers-FIG-1

Main +12V Power Connection.
Remote Connection.
Main Ground Connection.
To add an additional amplifier ground connection.
additional amplifier +12V power connection.

Charging and Discharging the capacitor

The capacitor must be charged before the first use. Connect the GND of the capacitor to the vehicle battery’s negative (-) terminal, then connect the +12V of the capacitor to the vehicle battery’s positive (+) terminal with the supplied resistor (Fig. 1), to prevent possible damage to the capacitor. When the voltage is between 10 and 12, you can disconnect the resistor. To discharge the capacitor, connect the GND to the +12V of the capacitor with the supplied resistor (Fig. 2). As it goes off, the capacitor is discharged and can be disconnected.

ZAPCO-HB-CB20F-DSP-Amplifiers-FIG-2