Senjoys AJ6201 Multi Functions Fire Pit Owner’s Manual

Senjoys AJ6201 Multi Functions Fire Pit

Specifications

• Product Name: Multi-functions Fire Pit
• SKU No.: AJ6201
• For Outdoor Use Only
• Min. Clearance: 48 inches (121.9 cm)
• Combustible materials should not be within 60 inches of the top of the unit or 48 inches of the entire unit

Product Usage Instructions

Safety Precautions

Before assembling or operating the fire pit, carefully read the entire owner’s instruction manual provided.

– Do not store or use gasoline or other flammable liquids near the appliance.
– Installation and service must be done by a qualified professional.
– Inspect the burner before each use and do not operate if damaged.
– Keep the control compartment, burners, and airways clean at all times.

Assembly Instructions

There are two solutions to use this fire pit:

1. Camping fire pit
2. Tabletop fire pit

• Make sure the gas valve is turned OFF before assembling and use the proper tools.
• Turn the cylinder valve on the tank clockwise to close the propane tank. Attach the regulator securely by turning the coupling nut clockwise.

FAQ

• Q: Can I use this fire pit indoors?
• A: No, this fire pit is designed for outdoor use only.
• Q: What should I do if rocks pop out during operation?
• A: Discard any popped rocks immediately to prevent injury.
• Q: Can I use a different regulator or hose assembly?
• A: No, only use the regulator and hose assembly provided with the unit. Replacement parts should come directly from the supplier.

DANGER
FIRE OR EXPLOSION HAZARD

• If you smell gas:
• Shut off the gas to the appliance.
• Extinguish any open flame.
• If the odor continues, leave the area immediately.
• After leaving the area, call your gas supplier or fire department.
• Failure to follow these instructions could result in fire or explosion, which could cause property damage, personal injury, or death.

WARNING

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
• An LP cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.

WARNING: If the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.

WARNING
For outdoor use only.

Installation and service must be performed by a qualified installer, service agency, or gas supplier.

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause injury or property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional information consult a qualified installer, services agency or gas supplier.

INSTALLER
Leave this manual with the appliance.
CONSUMER
Retain this manual for future reference.

DANGER

CARBON MONOXIDE HAZARD
This appliance can produce carbon monoxide which has no odor.
Using it in an enclosed space can kill you.
Never use this appliance in an enclosed space such as a camper, tent, car or home.

SAFETY INFORMATION

Before you assemble or operate this unit, please carefully read this entire manual. Failure to do so may result in a fire, explosion, injury or death.

WARNING

• The installation of this unit must adhere to local codes or the Propane Storage and Handling Code, CSA B149.2.
• THIS UNIT IS INTENDED FOR OUTDOOR USE ONLY! This product shall be used outdoors, in a ventilated space and shall not be used in any enclosed area.
• This unit is to be used with propane gas only! (sold separately)
• Do not attach a remote gas supply to this unit.
• Only use propane gas for this unit.
• Solid fuels shall not be burned in this appliance.
• When igniting this unit, stay away from the burner as the flame will light up and may cause injury.
• LP GAS WARNING: Do not use any more than 1/4 in-depth lava rocks/pumice stones/Lava Glass above the burner holes. Doing so will suffocate the flame.
• If the propane gas tank is leaking gas, you may hear, see, or smell a hiss. Do the following:
• Disconnect the propane gas tank. 2. Do not attempt to fix the problem yourself. 3. Contact your gas supplier or fire department for help.
• Applying too much propane may result in gas pooling and will not burn. Allow fresh air into the unit so that the remaining gas may escape.
• Do not use a flame to check for gas leaks.
• Manifold pressure: 11 inch w.c. (2.74 kPa).
• Use LP propane tanks with the following dimensions: diameter 12 in, height 18 in – capacity 20 lbs.
• You must use a propane tank that has a collar to protect the gas valve.
• DO NOT fill tank over 80 percent full.
• The tank system must be set up for vapour withdrawal.
• Discontinue use if any part of the propane tank is damaged. Rust and dents may be hazardous and should be inspected by a gas supplier.
• Do not burn anything other than the approved fuel for this fire table.
• Keep away from the unit for the first 20 minutes after igniting your unit for the first time, as lava rocks/pumice stones/lavaGlass could pop out and cause injury. Should any rocks pop out, discard them.
• Always ensure that lava rocks/pumice stones/lavaGlass are completely dry before use. Failure to do so will cause them to crack or pop.
• Do not operate the unit until all parts are fully assembled.
• Do not paint or colour any part of this heating unit.
• Unit may be hot while in use, do not attempt to move it while in use.
• Never leave this heating unit unattended while in use.
• This unit is not intended for cooking.
• Keep any flammable items away and do not use any other fireplace cover for this unit.
• Keep a safe distance to avoid burning skin or clothing.
• Do not sit or rest your hands or feet on this heating unit.
• Never place hands or fingers on an upper portion of this unit while in use.
• Keep all electrical cords and fuel supply hoses away from heated surfaces.
• Combustible material should not be within 60 inches of the top of the unit or 48 inches around the entire unit.
• Keep the appliance area clear and free from combustible material, gasoline and other flammable vapours and liquids.
• If the flame goes out while burning, turn the gas valve off. Wait 5 minutes before repeating the initial lighting procedure. Once you have a flame started, hold down the control knob for 1 minute.
• Do not add water to the unit.
• Do not operate the unit if any part has been underwater. Immediately call a qualified service technician to inspect the appliance and replace any part of the control system and any gas control that has been under water.
• Do not disconnect any part while the unit is in use.
• Do not store a spare propane tank on or near this unit.
• If the heating unit is indoors, detach the propane tank and leave it outdoors.
• Do not operate on a boat or vehicle. This unit must be used on a flat surface and outdoors ONLY.
• Always remove the protective cover before operating (if applicable).
• Do not set the protective cover over the unit until it is turned off and completely cooled down.
• Check for leaks after not using the unit for long periods.
• Children should never operate this unit. Children must be supervised while near this unit.
• Keep the gas tank at least 5 feet away from the unit when lit. (if external tank)
• Maximum gas supply: 250 psi; Min. gas supply: 10 psi.
• All installation and repair should be done by a qualified professional. This unit should be inspected annually and cleaned regularly.
• Inspect all elements of this heating unit before each use. If there is damage, the burner must be replaced.
• Keep the hose out of any pathways to eliminate any accidental damage. (if external tank)
• Be aware of the hazards of high temperatures and stay away from the unit to avoid any burns or injury.
• The gas supply tank should be constructed and marked with the specifications for the LP gas tanks of the U.S. Department of Transportation or the National Standard of Canada CAN/CSA-B339, LP gas tanks, spheres and tubes for Transportation of
• Dangerous Goods; and Commission.
• The LP gas tank must have a listed overfilling prevention device and a QCCI or Type I, (CGA791) LP gas tank connection.
• This heating appliance should not be used on plastic or artificial wood decks.
• Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition.
• Young children should be carefully supervised when they are in the area of the appliance.
• Clothing or other flammable materials should not be hung from the appliance or placed on or near the appliance.
• Any guard or other protective device removed for servicing the appliance shall be replaced before operating the appliance.
• Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a qualified service person. (More frequent cleaning may be required as necessary.) The control compartment, burners and circulating airways of the appliance must be kept clean.

IF APPLICABLE

• Allow the heating item to cool completely before placing it on the lid.
• DO NOT use a heating item while the lid is installed. Always remove the lid while the heating item is in use.

Only use the regulator and hose assembly provided with this unit. Replacement parts must be supplied directly by the supplier.
Inspect the burner before use of this unit. If the burner shows any kind of damage, do not operate the appliance.
NOTE: You must follow all steps to properly assemble this heating item. Make sure the gas valve is turned “OFF” before assembling. Do NOT attempt to assemble without proper tools.

• Combustible materials should not be within 60 inches of the top of the unit or 48 inches around the entire unit.

PARTS LIST

ASSEMBLY INSTRUCTION

1. Assembled hose with regulator by turning the coupling nut of hose to the quick joint tightly.
   ! Make sure it is fastened securely.

2. Extend or retract the legs of the stainless steel support manually.

TWO Solutions to use this unit.

Solution 1: Camping fire pit

• Place the fire pit on a firm level surface, put the stainless steel support onto the fire pit.
• Make sure the support stands securely.

Solution 2: Tabletop fire pit

• Place the fire pit on the tabletop.

• Place lava rocks into the fire bowl.

WARNING
This heating item should not be used on plastic composite or artificial wood.

• Turn the cylinder valve on the tank clockwise to close the propane tank. Attach the regulator to the cylinder valve by turning the regulator coupling nut clockwise.
• Make sure it is fastened securely and tighten connections by hand only.

• Cover the fire pit with a lid when not in use.

LIGHTING

Ignition Instructions

WARNING: Do Not Cover the Ignition Screen when placing the rocks into the re-bowl. Always keep the ignition screen visible.

WARNING: This heating item should not be used on plastic composite or artificial wood.

WARNING

• Don’t light or use a gas unit if lava rocks are wet. Ensure lava rocks are completely dry before igniting as intense heat could cause the rock to crack
• Keep away from the unit for the first 20 minutes after igniting your unit for the first time, as lava rocks could pop out and cause injury. Should any lava rocks pop out, discard them.

To Light

1. Make sure the control knob is in the “OFF” position.
2. Slowly open the valve on the propane gas tank by turning the knob counterclockwise.
3. Push in the control knob and turn to the “HIGH” position. Keep holding down the control knob to allow gas to flow for 15 seconds.
4. If ignition doesn’t occur within a few seconds release the control knob and rotate to the “OFF” position. Wait for 5 minutes for the gas to clear and then repeat the above lighting instructions.
5. Once the fire is lit, the flame intensity may be controlled by turning the control knob between the “LOW” and “HIGH” positions.

OPERATION

To Extinguish

1. Turn the control knob clockwise to the “HIGH” position; let the knob pop up and continue turning the control knob to the “OFF” position.
2. Close the cylinder valve on the propane gas tank if you don’t intend to use it for a long time.

MAINTENANCE

• Before performing any maintenance always disconnect the propane gas tank.
• Store your product indoors during winter months. Avoiding extreme cold temperatures will prevent exposure damage.
• Keep the heating item free and clear from combustible materials.
• Visually inspect the burner for obstructions and keep the tank enclosure free and clear from debris.
• Use a soft brush to get rid of the mild stains, loose dirt and soil after the burner and pumice stones/lava rocks/Lava Glass are completely cooled down. Wipe down with a soft cloth.
• Harsh weather conditions may cause stubborn stains, discolouration and possibly rust pitting.
• Permanent damage may occur if powder or solvent comes in contact with painted or plastic components on this heating unit.
• Keep the heating unit stored away from direct sunlight.
• If storing this unit inside, disconnect the propane gas tank from the gas valve.
• Not using manufacturer-approved or supplied parts/accessories may result in a defective condition and void the warranty of this heating unit.
• If desired, cover the fire pit to protect exterior surfaces and to help prevent build-up in air passages.
• Note: Wait until the fire pit is cool before covering.

TROUBLESHOOTING

Problem: Burner will not light using igniter

• Possible Cause 1: Electrode and burners are wet.
• Wipe dry with a cloth.
• Possible Cause 2: Igniter Pin cracked or broken – sparks a crack.
• Please contact us to request the parts.
• Possible Cause 3: Residue on Igniter Pin.
• Check for residue on the igniter pin or Thermocouple. If dirty, thoroughly clean the area.

Problem: The burner will not light with a match

• Possible Cause 1: No Gas Flow
• Check if the LP gas tank is empty. If empty, replace and refill. If the propane tank is not empty refer to Problem: Sudden drop in gas flow on the following page.
• Possible Cause 2: Coupling nut and regulator not fully connected.
• Turn the coupling nut about one-half to three-fourths a turn, until you feel a solid stop. Do not use tools, tighten by hand only Possible Cause 3: Obstruction of gas flow.
• Check for bent or kinked hose.
• Possible Cause 4: Spider webs or insect nests in the venturi.
• Clean the venturi. Venturi
• Possible Cause 5: Burner ports clogged or blocked.
• Reference Problem: Irregular flame pattern on the following page. Clean the burner ports as described there.

Problem: The fire table emits a lot of black smoke when in use

• Possible Cause 1: The hose from the gas fire table is pinched.
• Make sure the hose is not pinched between the fire table and the source of the gas.
• Possible Cause 2: Flame is being obstructed at burner ports. avate stre glasses as pont hame now are faye. of any
• Clear out the mixing chamber located before the Venturi.
• Possible Cause 3: The mixing chamber of the burn tube is blocked or obstructed.

Problem: Sudden drop in gas flow, or a reduced flame height

• Possible Cause 1: Out of Gas.
• Check for gas in the LP gas tank.
• Possible Cause 2: Excess flow safety device may have been activated.
• Turn control knob to OFF, wait 30 seconds and light the outdoor fire table. if flames are still too low, reset the excessive flow safety device by turning off the control knob and LP gas tank valve. Disconnect regulator. Turn the burner control knob to HIGH. Wait at least 5 minutes. Turn the burner control knob off. Reconnect the regulator and perform a leak check at the tank connection. Turn the LP gas tank valve on slowly, wait 30 seconds and then light the outdoor fire table.

Problem: Irregular flame pattern, flame does not run the full length of the burner

• Possible Cause: Burner ports are clogged or blocked.
• Clean burner ports. Do this by inserting a paperclip into each of the burner ports to ensure they are not clogged.
• WARNING: Make sure the burner is not on, and has had sufficient time to cool before touching it.

Problem: Flame blowout

• Possible Cause 1: High or gusting winds.
• Increase the flame to a HIGH setting.
• Possible Cause 2: Low on LP gas.
• Replace or refill the LP gas tank.
• Possible Cause 3: Excess flow valve tripped.
• Refer to Problem: Sudden drop in gas flow

Problem: Flame seems to lose heat when burning in cold weather – temperature below 50°F

Possible Cause 1: Ice has built up on the outside of the LP gas tank because the vaporization process is too low.
Turn the control knob and the LP gas tank to OFF. Replace with a spare LP gas tank and resume burning. Store the spare LP gas tank in a well-ventilated area, away from children.

If these troubleshooting steps are unable to resolve the problem. PLS contact customer service for technical support.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>