BUYDEEM S9013-91-A2 Water Dispenser User Manual
- June 1, 2024
- BUYDEEM
Table of Contents
S9013 BUYDEEM Water Dispenser
User’s Manual
Notice
IMPORTANT SAFEGUARDS
When using electrical appliances, basic safety precautions should always be
followed, including the following:
- Read all instructions.
- Do not touch hot surfaces. Use handles or knobs.
- To protect against fire, electric shock and injury to persons do not immerse cord, plugs, or housing body in water or other liquid.
- Close supervision is necessary when any appliance is used by or near children.
- Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts and before cleaning the appliance.
- Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or adjustment.
- The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electric shock or injury to persons.
- Do not use outdoors.
- Do not let cord hang over edge of table or counter or touch hot surfaces.
- Do not place on or near a hot gas or electric burner, or in a heated oven.
- To disconnect, turn any control to “off,” then remove plug from wall outlet.
- Do not use appliance for other than intended use.
- Save these instructions.
- HOUSEHOLD USE ONLY
a) A short power-supply cord (or detachable power-supply cord) is provided to reduce risks resulting from becoming entangled in or tripping over a longer cord.
b) Longer detachable power-supply cords or extension cords are available and may be used if care is exercised in their use.
c) If a long detachable power-supply cord or extension cord is used:
- The marked electrical rating of the detachable power-supply cord or extension cord should be at least as great entangled in or tripping over a longer cord.
- If the appliance is of the grounded type, the extension cord should be a grounding-type 3-wire cord.
- The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over.
SAVE THESE INSTRUCTIONS
DANGER
- To prevent the risks of electric shocks or short circuits, please do not putthe water dispenser, power cord, or plug in water or any other liquid.
WARNING
- Children, the elderly, people with limited physical or mental abilities, and those without any experience of using similar products should only use this product under supervision and guidance, which ensures their safety. This product is not intended for use by children without supervision and guidance from someone who can take responsibility for their safety.
- This product must be used alone with a grounded outlet with a rated current above 10A and a rated voltage of 120V~ 60Hz. The plug must be fully inserted into the outlet to prevent overheating of the components caused by poor contact, which might lead to the risks of short circuits or fire hazards. Do not use a universal outlet.
- Please keep the water dispenser and power cords away from high temperatures, open flames, damp, smooth surfaces, or sharp edges to prevent component damage, failures, or fires.
- To prevent electric shocks, please do not use the water dispenser with wet hands or bare feet.
CAUTION
- This product is designed for home use only. The manufacturer only provides warranty repair for production defects and faults arising from home use. The manufacturer is not responsible for any consequences or faults caused by any commercial use, unsuitable use, or failure to follow the instructions. Such faults and damage are not covered by the warranty.
- Please check whether the voltage displayed on the product specification label is consistent with the main voltage before using the product.
- If the power cord is damaged, it must be replaced by a professional from the manufacturer, its service department, or a similar department to avoid danger.
- Please always place the water dispenser on a flat, stable, and heat-resistant workbench.
- Please keep this product away from direct sunlight, high-temperature surfaces, or any places close to a heat source. Otherwise, the water dispenser body might fade, and bacteria might grow. Please do not put the water tank in places with direct sunlight or high humidity for a long time. Otherwise, moss might grow.
- Please unplug the power plug immediately if the water dispenser does not work properly.
- If you need to pull out the plug, please hold the plug with your hands and pull it out.
- Please do not pull or twist the power cord by force. Otherwise, a risk of electric leakage might occur due to damage to the power cord.
- Please do not hang the power cord outside the edge of the table or workbench surface. Otherwise, the water dispenser might fall or cause trip hazards.
- Please do not move the water dispenser when it is working. Otherwise, it might lead to the risk of scalding.
- It is normal for low ambient temperature and low voltage to cause a relatively reduced hot water flow. When hot water reaches the boiling point, the water output might come along with relatively more vapor. It is normal to see some remaining water drain out after the heating process is completed. It is normal that there is a slight misalignment between the output water temperature and the chosen temperature within a certain range.
- Keep the water dispenser from moisture and freeze.
- Please unplug the water dispenser if you do not use the water dispenser for a long time or clean it with a damp cloth.
- To let the water dispenser work properly, please put the water tank on the dispenser body.
- It is recommended to empty the water tank if the water dispenser is not used for a long time.
- Do not add hot water at a temperature over 50°C to the water tank. Do not let the water tank and its lid come into contact with water at a temperature over 50°C.
- Otherwise, it might cause deformation or odor.
- Please do not clean the water dispenser with other methods that are not recommended.
- For recommended methods, please refer to Cleaning and Maintenance in the user’s manual.
- It is recommended to add clean drinking water to the water dispenser. Dirt can lead to bacteria growth and odor in the water dispenser.
- If the components of the water dispenser are damaged or cannot work properly, please unplug the power plug immediately. Do not use it or dismantle it by yourself. Please come to a service center authorized by BUYDEEM for replacement or repair.
- Any other use and operations apart from normal cleaning and descaling that are specified in the manual must be conducted by a service center authorized by BUYDEEM.
- Any malfunction or failure to work caused by a lack of cleaning and descaling is not covered by the warranty.
- All products are manufactured following the quality control procedure, including the actual use testing of randomly selected products, which explains any evidence of use on the products.
Technical Specifications
Name | BUYDEEM Water Dispenser | Model | S9013 |
---|---|---|---|
Rated Power | 1600W | Rated Voltage | 120V~60Hz |
Product Materials | This product is made of food-grade materials, including |
polypropylene, styrene-acrylonitrile resin, SU304 (06Cr19Ni10) stainless steel, and food-grade silicone.
Understanding Product
Product Structure
① Temperature Regulation Knob/Water Output Button (hereinafter referred to as
“Knob”)
② Clean Button
③ Output Volume Adjustment Button
④ Unlock Button
⑤ Outlet| ⑥ Metal Drip Tray
⑦ Water Dispenser Body
⑧ Water Tank Lid
⑨ Water Tank Handle
⑩ Water Tank
---|---
Button Function Introduction
Panel | Function Name | Function Operation Modes |
---|---|---|
Basic Functions | Lock/Unlock | Due to safety concerns, when the default Auto |
Lock mode is activated, the water dispenser will be locked automatically if it
is idle for one minute after use. The water dispenser can be unlocked or
locked manually with this button. Note: When the Auto Lock mode is activated,
pressing this button can also stop dispensing water.
Adjust Output Volume| Available output volume: 100mL/200mL/300mL/500mL/800mL.
The two buttons for adjustment are on the left and right sides of the output
volume indicator light. Press the left Output Volume Adjustment button, and
then the output volume will move to the left for one unit. When the output
volume is at the far left, press the left button again, and it will move to
the far right. The right button works in the same way.
Water Temperature Regulation| Available water temperature: Room
Temp/40°C/50°C/60°C/70°C/ 80°C/90°C/Boil. The temperature cannot be changed
during the process of dispensing water.
Note: In temperature settings (40°C to 90°C) apart from the Boil mode,
the water will no longer be heated up after it reaches the target temperature.
Knob| Press this button to start or stop dispensing water.
Clean| Clean the water pipes through this function. For specific operation
steps, please refer to Cleaning and Maintenance in the user’s manual. Before
using this function, please carefully read the user’s manual and the cleaning
tip on the side of the device to prevent accidents.
Advanced Functions| Cancel/Activate Auto Lock| The Auto Lock function can be
canceled with this function, keeping the water dispenser in standby mode. (For
more details, please refer to Auto Lock in the user’s manual.)
Boiling Point Measurement| The water dispenser can measure the current boiling
point and reset the boiling temperature. (For more details, please refer to
Boiling Point Measurement in the user’s manual.)
Using Product
Initial Use
-
Please remove all the packaging, labels, and accessories inside and outside the water dispenser before using the product for the first time.
-
It is normal to see some remaining water after pulling out the silicone dust plug at the outlet downward.
Note: For product quality, every device needs to pass the outgoing inspection in terms of the water dispensing function. -
It is normal to see some remaining water after tearing off the dustproof sticker from the inlet.
-
Take out the water tank and clean it with water. When cleaning the inside and outside of the water tank, do not let the water tank, the lid, and the handle come into contact with water at a temperature over 50°C. To avoid deformation, please do not steam or boil the water tank.
-
Before drinking the water for the first time, please clean the water pipes. For detailed steps of cleaning, please refer to Cleaning and Maintenance – Internal Cleaning in this user’s manual. Please do not interrupt the cleaning process in non-emergencies.
Daily Use
-
Take out the water tank
● Take out the water tank.
● Open the water tank lid. -
Add a right amount of room-temperature purified water
● Add a right amount of drinking water to the water tank.
● Do not fill up the water tank below the “MIN” line or beyond the “MAX” line.
● For health reasons, it is suggested that you use purified water or mineral water. -
Put the water tank back into its base
● Please place the water dispenser on a flat, clean, and heat-resistant surface.
● The water tank shall align the groove in the middle of the water dispenser. Make sure that the hook outside the water tank aligns with the hook on the body of the water dispenser. -
Place the drip tray
● Put the drip tray in front of the dispenser body. Adjust the position to make it right under the outlet. -
Activate the water dispenser
● After plugging in power, all lights on the water dispenser panel will flash with a long “beep” sound generated. The Unlock button and the 200mL indicator light will stay on after the Lock mode is on. All other button lights will turn off. The water dispenser is then activated.
Daily Use
-
Unlock
Press the Unlock button for 1 second. The Unlock button light will then turn off (Picture 1). -
Unlock Notification Sound
If you try to operate the water dispenser when the Lock mode is on, two beeps sound will be generated to remind you that you need to unlock it first. -
Choose Output Volume
Press either Output Volume Adjustment button to adjust the output volume. The Output Volume indicator light will show the specific output volume. If not adjusted this time, the output volume will follow the last setting. After a chosen output volume of 800mL is dispensed, the water dispenser will automatically restore to the output volume of 200mL (Picture 2). -
Choose Water Temperature
Eight levels of water temperature are available: Room Temp/40°C/50°C/60°C/70°C/ 80°C/90°C/Boil. Turn the knob to choose a temperature. Please note that the water temperature cannot be adjusted during the process of water dispensing (Picture 3). -
Dispense Water
Press the knob to start dispensing water (Picture 4). -
Stop Dispensing Water
Press the knob to stop dispensing water. (When the Auto Lock mode is activated, a short press on the Unlock button can also stop dispensing water.) (Picture 6) -
Cancel Auto Lock function
When the Child Lock mode is on, press the Unlock button and the knob at the same time. After three beeps sound, the Unlock button light will turn off. The Auto Lock function is then canceled. The water dispenser will not be locked automatically. You can directly use it without turning off the Child Lock again.(Picture 7) -
Reactivate Auto Lock function
When the Auto Lock function is inactive, press the Unlock button and the knob at the same time. After you hear three beeps, the Unlock button will light up. The Auto Lock function is then reactivated. The water dispenser will be locked automatically if it is idle for one minute after use. When the Lock mode is on, you need to unlock the water dispenser first for further operation.(Picture 7)
Cleaning and Maintenance
Cleaning and Maintenance
It is normal to smell a slight odor when you unbox the device and use it for
the first time. Please leave the device in a ventilated place, and the odor
will gradually go away. For water safety, it is suggested that internal
cleaning should be conducted when you use the new device for the first time.
-
External Cleaning
● Unplug the power plug.
● Use clean water to clean the water tank and wipe it to dry it. Please do not steam or boil the water tank or use water at a temperature over 50°C.
● Use wrung cloth to wipe and clean the device surface after the water dispenser completely cools off.
● Only the outside of the water tank can be washed with water. Never immerse any part of the water dispenser in water. -
Internal Cleaning
Note: Do not interrupt the cleaning process after it starts. Otherwise, some cleaning solution may remain.
● The cleaning process is divided into two rounds. The drainage volume and water temperature are both controlled by the process.
● Add BUYDEEM cleaning tablet before cleaning. You can choose whether to add the cleaning tablet or not before you use the water dispenser for the first time. It is suggested that you can add the cleaning tablet every time for daily cleaning after use.
● How to use the cleaning tablet: Add 1000mL of room temperature purified water or purified water at a temperature below 50°C to the water tank with 1 or 2 pieces of BUYDEEM cleaning tablets. Stir or let the cleaning tablet sit until it completely dissolves. For safety reasons, please do not operate the water dispenser before the cleaning tablet completely dissolves.
● Prepare a container with a capacity of 3000mL and place it under the outlet. Long press the Clean button to start the cleaning process.
● The water dispenser will drain out all the water in the water tank in the first round of cleaning.
● After the first round of drainage, the Clean button will light up continuously. The knob will flash with a long “beep” sound generated. Please take down the water tank and wash it with clean water at a temperature below 50°C and make sure that there is no remaining cleaning solution in the water tank.
● Add 3000mL of room temperature purified water to the cleaned water tank (please do not add any cleaning tablet in this step). Press the knob to start the second round of drainage. 2000mL of hot water will drain out in this round. Please be careful and do not get scalded.
● The cleaning is done. You can use the water dispenser as usual.
Tip: After the cleaning process, set the output volume to 800mL and let the water dispenser drain out water at a temperature over 50°C again. This can clean the pipes more thoroughly.
CAUTION:
- If the calcium content of your daily drinking water is higher than 30mg/L, or if floating white particles occur in the water dispenser within 30 days of use, it is suggested that you clean the water dispenser every 10 days.
- If the calcium content of your daily drinking water is lower than 30mg/L, or if floating white particles occur in the water dispenser after 30 days of use, it is suggested that you clean the water dispenser every 30 days.
- If floating white particles occur in the water dispenser when you use it for the first time, it indicates that the water hardness is very high. It is suggested that you change your water supply or use purified water.
Advanced Functions
Boiling Point Measurement
Why do we need a boiling point measurement?
-
At high altitudes, the boiling point of water cannot reach 100°C, which makes it difficult for common water dispensers to work normally (the boiling of water takes too long or even fails).
-
BUYDEEM suggested that you should always conduct a boiling point measurement when you use the water dispenser for the first time. When the measurement is done, the chip will record the data of specific boiling points. There is no need to measure it
again when you use the water dispenser later. -
With the boiling point measurement function, the water dispenser can work more accurately (the performance will become better than in the factory setting).
-
If you live in a place at an altitude of over 250 meters, please make sure you conduct a boiling point measurement before you use the water dispenser.
Start Boiling Point Measurement
-
Prepare a container with a capacity of around 1L and place it under the outlet. To ensure the accuracy of the boiling point measurement, please drain out 500mL of room temperature water before starting the boiling point measurement. After the drainage, long press the left and right Output Volume Adjustment buttons at the same time. After you hear three beeps, the boiling point measurement starts.
-
During the measuring process, the left and right Output Volume Adjustment buttons will light on. The breathing light mode of the knob light will be activated.Lights on the Output Volume bar will turn on one by one.
-
The water dispenser will drain out water continuously for about 10 to 30 seconds.
Please do not interrupt the drainage. Please be careful and do not get scalded. -
When the drainage stops with a long “beep” sound generated, the process is complete.
Note:
-
Please make sure that the water dispenser can complete an automatic boiling point measurement uninterruptedly so that the detected boiling point can be recorded. If the process is interrupted for any reason, please restart the process.
-
The automatic boiling point measurement cannot change the local boiling point.
When the target water temperature is set as “Boil”, the water will be dispensed automatically if the water has reached the local boiling point. -
It is normal that any click or boiling sound generates during the process of boiling point measurement.
Simple Troubleshooting
Simple Troubleshooting
Problem | Possible Causes | Troubleshooting |
---|---|---|
After powering on, the buttons or knob of the water dispenser do not light up | ||
No power supply | Check if the socket is plugged in | |
Product failure | Please contact the service center of purchase channel which |
authorized by BUYDEEM for replacement or repair
The knob button and the Output Volume Adjustment button flash at the
same time with a long “beep” sound generated| The water tank is not properly
installed| Please install the product following the manual
The water level in the water tank is too low| Add enough water to the water
tank
Improper water level| Unplug the power plug and restart the water dispenser
Product failure| Please contact the service center of purchase channel which
authorized by BUYDEEM for replacement or repair
All the lights flash with a long “beep” sound generated| The water
temperat- ure in the water tank is over 50°C| Add water at a temperature below
50°C
Product failure| Please contact the service center of purchase channel which
authorized by BUYDEEM for replacement or repair
Odor in water| Product failure| Please refer to Cleaning and
Mainte- nance in the user’s manual and clean the water dispenser. If the odor
in the water still exists, please contact the service center of purchase
channel which authorized by BUYDEEM for replace- ment or repair.
Warranty
Warranty card
Dear Customer,
Thank you so much for your purchase! The product comes with a ONE-YEAR
warranty.
If you need any warranty support, please have the following information handy
when contacting us:
Product Model No.:………………….
Factory Serial No.:…………………….
Order ID:………………………………
Customer Phone:……………………
Product Name:……………………
Order Date:……………………………
Customer Name:……………………
Customer Email:…………………..
Please feel free to email us if have any questions or concerns.
More information, visit website: us.buydeem.com
This warranty does not apply:
- If the product has been modified from its original conditions;
- If the product has not been used in accordance with directions and instructions in the user manual;
- To damages or defects caused by accident, abuse, misuse, or improper or inadequate maintenance;
- To damages or defects caused by service or repair of the product performed by an unauthorized service provider or by anyone other than BUYDEEM;
- To damages or defects occurring during commercial use, rental use, or any use for which the product is not intended;
- To damage or defects exceeding the cost of the product.
Shenzhen Buydeem Technology Co., Ltd.
Room 3801, Building A, Tanglangcheng West, No.3333 Liuxian Boulevard,
Nanshan District, Shenzhen, China.
S9013-91-A1
Please refer to the real product in case of any change
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>