Conquer Industry Co Ltd CQL1975-B BSBTMSGEYE Bluetooth Eye Mask Speaker Instruction Manual
- June 1, 2024
- Conquer Industry Co Ltd
Table of Contents
CQL1975 /BSBTMSGEYE Bluetooth Eye Mask Speaker
Instruction Manual (Read before proceeding)
In the box
Eye mask speaker x1
Cold & Hot gel insert x1
Micro USB charging cable x1
User manual x1
To charge the battery:
- Unzip the eye mask and you will find the Bluetooth device inside it next to the zipper opening.
- Take the Bluetooth device out.
- Using a Micro USB Charging Cable (included), insert the USB power cable into the micro USB port located on the side of the device. Connect the other end of the USB cord into a powered USB source such as a computer, laptop or USB AC adapter.
The LED indicator will turn RED while charging and turn OFF when fully
charged.
Put the Bluetooth device into the eye mask in correct position and zip up the
eye mask.
Button control:
| Press and hold: Power on/off
Press: Play/pause
Phone calls: (Press) Answer the phone call (2xPress) Dia last calling number
---|---
| Press and hold: Vol –
Press: previous track
| Press and hold: Vol +
Press: Next track
Playing Music via Bluetooth
- Press and hold the power switch to activate the Bluetooth function.
- A tone will be heard and the LED light flashes red and blue, which indicating that the speaker is in pairing mode and searching for your Bluetooth device.
- Make sure the Bluetooth function on your device is turned on.
- Search the device named “XXX”
- Once you have selected the speaker, your device will pair without a password. (If your device prompts for a password, enter the password”0000”.)
- Once your speaker is paired, the blue indicator light will be flash slowly
- Start playing music on your device. Make sure that you keep your device within a 33 feet range of your eye mask speaker.
- Adjust the volume of your device or the buttons on eye mask to a comfortable level.
- Press and hold the power switch again to turn off the unit when not in use.
Using the Hot & Cold insert
- Cold: Chill the gel insert in refrigerator 2 hours for cold therapy until the mask has reached the desired temperature. (Do not put in the freezer for more than 2 hours, No time limit on the refrigerator).
- Hot: Place eye mask in microwave oven for 10~12 second.
Unzip the eye mask and put the gel insert in , zip the eye mask.
Simply apply it to the face.
Caution:
- This is not a toy. Please keep away from children.
- Please keep away from water / heat.
- Low power may cause poor connection even no working of Bluetooth.
- Do not overcharge the battery.
- Battery pack shall not be exposed to excessive heat such as sunshine, fire or the like.
- Please do make sure the inside Bluetooth device are taken out before washing the eye mask.
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions (1)this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired
operation.
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>