BSRF AS-84 Combiner Splitter User Manual
- June 1, 2024
- BSRF
Table of Contents
User Manual
AS-84
Version 01
Read first:
– First of all read this manual.
– Clean the device with a slightly damp cloth.
– This device must’nt be exposed to rain, moisture.
– Do not install the device near any heat sources.
– This device must be serviced by a qualified service personnel.
– Specifications are subject to change without notice.
– BSRF is not responsible of any injuries, destruction resulting of improper
usage of equipments.
About AS-84
Introduction :
The AS-84 is a combiner and a splitter in a small form factor. 4 inputs and 8
outputs. Wideband and tunable narrow band filter are buitin. 4 inputs allows
you to do zoning, it means summing signal from antennas to cover to different
place or cover a broader area.
Keypoints :
- 2 antenna input pairs, selectable or summable
- Wideband and tunable narrowband filter buit-in
- 12V regulated DC feed
- RF power bargraph
- Compact and rugged
What is needed with AS-84 :
-Power source (9 -18V) and power cable (4 point push pull type)
-Two 50ohms coax for antennas(BNC), coax for receivers(SMA) and SMA loads for unused ports.
Description
Connecting :
- Connects outputs to wireless receiver inputs (or combiner, splitter)[4/5].
- Connects inputs to antenna thourgh coax cable[1/2].
- Connect power to DC[3]. Pinout : 1,2:GND 3,4:VIN
- Add DC feed on requested port (DC) and select the input port (1 or 2 or 1+2 sum).
Leds :
Peak:
- Those leds light up when the signal exceed the RF threshold .This threshold can be set in the menu.
DC :
- Those leds light up when the corresponding DC feed is applied to the port.
It will blink if a too much is drawn or if there is a short circuit.
SW :
- SW leds indicate witch input channel is selected
Display
Oled display :
Main screen displays (Illustration 1):
- Filter selected and frequencies
- RF bar power (-40 up to 0dBm)
- DC feed configuration
- RF input selection
- In menu set thresholds
Unlock :
- Press the switch for until the locker is unlocked (right bottom side of display)
Filter :
- Press the switch and rotate encoder to select WB(wideband) or NB(narrowband) filter. In NB anothr pression will allow you to tune the central frequency of the filter
DC feed & input selection :
- Press encoder to select DC and rotate encoder to change the DC config, do the same to change the SW config aka wich input are selected
The ‘*’ appears next item that can be modifed using the encoder.
More
Using 4 antennas, two configuration :
-Extending zone : area are overlapping. It means that antenna 1 and 2 receive in overlapping zone the same signal.
-Multizone : area are not overlapping. It means that antenna 1 and 2 don’t receive the signal of the other zone (or with attenuation).
Specifications
Wideband filter | 470-700MHz | @-3dB |
---|---|---|
Narrowban d filter | 50 to 70MHz bandwidth | Tunable from 470 up to 740MHz (32 |
steps)
Gain| 1dB| +/-1dB
Max RF in| +20dBm|
Noise figure| <2dB typ.| Amplifiers
A/B isolation| 80dB typ| Channel isolation
OIP3| 39dBm typ.|
RF peak thresholds| -5dBm (high)
-20dBm (low)| +/-1dB
DC feed| 12V/200mA| 12V Regulated
DC In| 4 pts| (-):1&2 (+):3&4
Supply| 12-18V| 75mA typ.
without DC feed
Dimensions| 83x60x31mm|
Weigth| 0,25kg|
(Subject to change without notice)
Warranty
This 2 year limited Warranty covers any defects in material or workmanship
under normal use during the Warranty Period.
During the Warranty Period, BSRF will repair or replace, at no charge,
products or parts of a product that proves defective because of improper
material or workmanship, under normal use and maintenance.
Send an email first at: contact@bs-rf.com
More informations on www.bs-rf.com
Mail : contact@bs-rf.com Tél : 33(0)9 67 85 88 24
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>