TAC 3B-F150T Bull Bar 3 Inch Texture Black Instruction Manual
- June 1, 2024
- TAC
Table of Contents
TAC 3B-F150T Bull Bar 3 Inch Texture Black
Specifications:
- Model: 3 BULL BAR 2021-2024 FORD BRONCO
- Part Number: 3B-F150T
- Material: Stainless Steel
- Finish: Gloss Black
Product Usage Instructions
Installation:
- Identify the parts included in the package: 3in Bull Bar, Lower and Upper Brackets, Support Brackets, Bolts, Washers, Lock Washers, and Nylon Lock Nuts.
- Start with the driver/left side installation:
- Remove the plastic bumper cover and splash guard.
- Insert the Upper Mounting Bracket and Support Bracket between the frame and tow hook.
- Attach the Lower Mounting Brackets and Support Brackets to the model with a plastic bumper cover.
- Secure all brackets using the provided hardware.
- Repeat the same steps for the passenger/right-side installation.
- Ensure all brackets are tightly secured before proceeding.
Maintenance:
To protect your investment, follow these maintenance tips:
- After installation, wax the product to add a protective layer over the finish.
- Regular waxing is recommended to maintain the protective layer.
- Avoid using polish or wax with abrasives that could damage the finish.
- For stainless steel finishes, use aluminum polish for small scratches and scuffs.
- Clean the Bull Bar with mild soap for both stainless steel and gloss black finishes.
FAQ:
Q: Can this Bull Bar be installed on other vehicle models?
A: This specific Bull Bar is designed for use on the 2021-2024 Ford
Bronco. It is recommended to check with the manufacturer for compatibility
with other vehicle models.
Q: Is professional installation required?
A: While DIY installation is possible with basic tools,professional
installation by a certified technician is recommended to ensure proper fitting
and secure attachment.
3” BULL BAR
2021-2024 FORD BRONCO
PART# 3B-F150T
PARTS LIST
| 1 | 3in Bull Bar | 4 | 10-1.5mm x 40mm Hex Bolts |
|---|---|---|---|
| 1 | Driver/left Lower Bracket | 6 | 10-1.5mm x 30mm Hex Bolts |
| 1 | Passenger/Right Lower Bracket | 18 | 10mm x 30mm OD x 2.5 mm Flat Washers |
| 2 | Support Brackets | 2 | 10mm Lock Washers |
| 1 | Driver/left Upper Bracket | 8 | 10-1.5mm Nylon Lock Nuts |
| 1 | Passenger/Right Upper Bracket |
PROCEDURE:
REMOVE CONTENTS FROM BOX AND VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. CUTTING MAY BE REQUIRED. INSTALLATION MAY INTERFERE WITH FRONT- MOUNTED SENSORS.
-
Start installation from under the front of the vehicle. Remove the splash guard from below the bumper,(Figure 1).
-
Determine if the vehicle is equipped with plastic bumper cover or steel option bumper.
Models with plastic bumper cover:-
Remove the plastic cover surrounding the driver/left tow hook, (Figure 2). NOTE: Cover cannot be reinstalled.
-
Loosen the (2) hex bolts attaching the tow hook to the bottom of the frame, (Figure 2). IMPORTANT;
Do not remove the hex bolts, only loosen. -
Select the driver/left Upper Mounting Bracket, (Figure 3).
-
Insert the Upper Bracket through the gap between the bottom of the frame and the top of the tow hook, (Figure 4). Tighten hardware at this time.
-
Repeat the previous Steps to install the passenger/right Upper Mounting Bracket.
-
Reinstall the splash guard, (Figure 5).
Models with optional steel bumper: -
Remove the driver/left side cover surrounding the tow hook from the bumper, (Figure 6).
-
Loosen the (2) hex bolts attaching the splash guard bracket to the bottom of the frame. IMPORTANT;
Do not remove the hex bolts, only loosen. -
Select the driver/left Upper Mounting Bracket, (Figure 3).
-
Insert the Support Bracket through the opening between the bottom of the tow hook and the bumper,(Figure 7). Slide the end of the Bracket between the splash guard bracket and the bottom of the frame. Tighten bracket hardware at this time.
-
Reinstall the cover surrounding the tow hook.
-
Repeat the previous Steps to install the passenger/right Upper Mounting Bracket.
-
Reinstall the lower splash guard.
-
-
Select the driver/left Lower Mounting Bracket, (Figure 8).
-
Hold the Bracket up to the bottom of the splash guard. Line up the hole in the Bracket with the mounting bolt hole for the splash guard. Attach the Bracket to the Spacer and splash guard with (1) 10mm x 40mm Hex bolt, (1) 10mm Lock Washer and (1) 10mm Flat Washer, (Figure 9). Leave hardware loose.
-
Next, select (1) outer Support Bracket. Attach the Support Bracket to the outside of the Lower Mounting Bracket with the included (2) 10mm x 30mm Hex Bolts, (4) 10mm Flat Washers and (2) 10mm Nylon Lock Nuts, (Figures 10 & 11). Leave hardware loose.
-
Repeat Steps 3—5 to attach the passenger/right Lower Mounting Bracket and Support Bracket.
-
Carefully unwrap the Bull Bar.
-
With assistance, hold the Bull Bar in position up to the Mounting Brackets. Slide the mounting tab on the driver/left side of the Bull Bar between the Upper Mounting Bracket and outer Support Bracket, (Figure 12). Insert (1) 10mm x 40mm Hex Bolt, (2) 10mm Flat Washers and (1) 10mm Nylon Lock Nut through the lower hole in the Support Bracket, tab on Bull Bar and Upper Bracket. Insert (1) 10mm x 30mm Hex Bolt,(2) 10mm Flat Washers and (1) 10mm Nylon Lock Nut through the top hole in the Support Bracket and Bull Bar, (Figures 12 & 13).
-
Repeat Step 8 to attach the passenger/right side of the Bull Bar.
-
Check the Bull Bar alignment with the vehicle and for clearance between the Bull Bar and the bumper.
Adjust as required then fully tighten all hardware at this time. -
Do periodic inspections to the installation to make sure that all hardware is secure and tight.
To protect your investment, wax this product after installing. Regular waxing
is recommended to add a protective layer over the finish. Do not use any type
of polish or wax that may contain abrasives that could damage the finish.
For stainless steel: Aluminum polish may be used to polish small scratches and
scuffs on the finish. Mild soap may be used also to clean the Bull Bar.
For gloss black finishes: Mild soap may be used to clean the Bull Bar.
Driver/left Side Installation Pictured
(Fig 1) Example of model with plastic bumper cover. Remove splash guard (arrow)
(Fig 2) Remove plastic cover surrounding tow hook. Loosen tow hook bolts (arrows)
(Fig 3) Insert driver/left Upper Mounting Bracket between frame and tow hook
(Fig 4) Models with plastic bumper cover, insert driver/left Support Bracket between frame and tow hook
(Fig 5) Install passenger/right side Upper Bracket and reinstall splash guard
(Fig 6) Model with steel bumper, remove lower splash guard/skid plate and cover around tow hook (driver/left side pictured)
(Fig 7) Models with steel bumper, insert Upper Bracket between tow hook and opening in bumper (arrow). Attach end of Bracket to bottom of frame, between frame and splash guard bracket. Reinstall splash guard/skid plate and cover
(Fig 8) Attach driver/left Mounting Bracket to the outside of the splash guard
(Fig 9) Driver/left side Upper and Lower Mounting Brackets attached to model with plastic bumper
(Fig 10) Attach Support Bracket to outside of driver/left side Lower Mounting Bracket
(Fig 11) Driver/left side Brackets installed
(Fig 12) Insert tab on driver/left end of Bull Bar between Outer Support Bracket and Upper Mounting Bracket
(Fig 13) Driver/left side of Bull Bar attached to Brackets
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>