VOLLRATH T38712 Cafeteria Breath Guard Instruction Manual
- June 1, 2024
- VOLLRATH
Table of Contents
VOLLRATH T38712 Cafeteria Breath Guard
Product Information
- Specifications:
- Product Name: Cafeteria Breath Guard
- Model: One Piece and Three Piece
- Manufacturer: Vollrath Company, L.L.C.
- Item No.: 2350030-01 Rev 04/12
Product Usage Instructions
- One Piece Breath Guard Installation:
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figure 1. Repeat for all four uprights.
- Three-Piece Breath Guard Installation:
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown in Figures 1 and 2. Repeat for all four uprights.
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the one-piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
- Install the side breath protector (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.
FAQs
- Q: What should I do if I encounter cracks in the plastic parts during installation?
- A: If you encounter cracks in the plastic parts during installation, stop tightening immediately to prevent further damage. Contact customer service for assistance and replacement parts.
- Q: Can the breath guard be easily removed for cleaning?
- A: Yes, the breath guard can be easily removed for cleaning by following the installation steps in reverse order.
Installation Instructions
METHOD 1
- One Piece Cafeteria Breath Guard Three Piece Cafeteria Breath Guard
- These instructions cover the installation of the one-piece Cafeteria Breath Guard and the three-piece Cafeteria Breath Guard.
One Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the
breath guard follow these steps:
NOTE: Use caution when tightening the cap nuts. Overtightening may cause
the plastic to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figure 1. Repeat for all four uprights.
- Figure 1. One Piece Breath Guard Installation
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the one-piece breath guard (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all four mounting locations.
- Install the side breath protector (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.
METHOD 2
Three-Piece Breath Guard Installation
Some units are shipped with a breath guard not installed. To install the
breath guard follow these steps:
NOTE: Use caution when tightening the cap nuts. Overtightening may cause
the plastic to crack.
- Install the breath guard uprights (A) to the studs (B) securing with cap nuts (C) as shown. See Figures 1 and 2. Repeat for all four uprights.
- Figure 2. Three-Piece Breath Guard Installation
- Install the breath guard support tube (D) between the uprights (A) securing with cap nuts (C) as shown. Repeat on the other side.
- Install the side breath guards (E) securing with screws (F) and cap nuts (C) as shown. Repeat for all mounting locations.
- Install the side shield (G) to the support tube (D) securing it with cap nuts (C) as shown. Repeat on the other side.
- Install the support bar and stud assembly (H) to the side breath guards (E). Repeat for all mounting locations.
- Install the top breath guard (I) to the support bar and stud assembly (H) securing with cap nuts (C). Repeat for all mounting locations.
CONTACT
- The Vollrath Company, L.L.C. 1236 North 18th Street Sheboygan, WI 53081-3201 U.S.A.
- Main Tel: 800.628.0830
- Service Tel: 800.628.0832
- FAX: 800.752.5620
- Vollrath of Canada, Co.
- Tel: 800.695.8560
- FAX: 800.752.5620
- © 2010 The Vollrath Company, L.L.C.
- www.vollrathco.com.
- Item No. 2350030-01
- Rev 04/12
References
Read User Manual Online (PDF format)
Loading......