BAENUE BNU-DL001 Lamp Desk Light Owner’s Manual
- June 1, 2024
- BAENUE
Table of Contents
INSTALLATION
/
FEATURES
Installation
Step 1
Step 2
Step 3
Step 4
- Aligned
- Mis-aligned
Lock Unlock
Step 5
- Power On/Off
Features
- Dim2Amber™
- Sunset Sleep Timer
- Optical Shift
- 110° Swing
- Automatic On/Off
- Charger
Product Information
- 110° Swing
- Wireless Charger
- Automatic On/Off Sensor
- Optical Shift
- Power Switch
- Dim2Amber™ Dial
- USB C Charger
- Sunset Sleep Timer
- Automatic On/Off
Read All Instructions Before Using
IMPORTANT SAFETY INSTRUCTIONS
- Please follow this guide to install this product accurately and safely, and keep this guide in a safe place to refer to it later. These warnings apply to the light, and also where applicable to chargers or mains adaptors. To reduce the risk of fire, electric shock, or injury:
- Ensure that the product is fully assembled in line with the instructions before use.
- Do not allow the product to be used as a toy. Close attention is necessary when the product is used near children.
- Use caution not to drop parts including the pole while assembling. Do not swing the product or the pole as it can cause injuries.
- Use only as described in the user manual. Do not carry out any maintenance other than that advised by the helpline.
- This product can be used by persons with reduced physical, sensory or reasoning capabilities, or lack of experience and knowledge, only if they have been given supervision or instruction by a responsible person concerning use of the light in a safe way and understand the hazards involved.
- Cleaning and maintenance shall not be performed by children.
- Suitable for dry indoor use only at ambient temperature between 0℃(32℉) and 35℃ (95℉).
- If the product is not working as it should, has received a sharp blow, has been dropped, damaged, left outdoors, or dropped into water, do not use it and contact the helpline.
- If a service or repair is needed, contact the helpline to discuss available options. Do not disassemble the light as incorrect reassembly may result in an electric shock or fire.
- This product is only to be used with the power supply unit provided with it.
- Do not handle any part of the product, cable or plug with wet hands.
- Do not use the product with a damaged cable or plug. If the supply cable is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
- Do not stretch the cable or place the cable under strain. Keep cable away from heated surfaces.
- Do not route the cable under furniture or appliances. Do not cover the cable with throw rugs, runners or similar coverings. Arrange the cable away from traffic areas and where it will not be tripped over.
- Do not unplug by pulling on the cable. To unplug, grasp the plug, not the cable. The use of an extension cable is not recommended.
- Turn off all controls before unplugging. Unplug from the socket when not in use for extended periods. To avoid a tripping hazard, safely coil the cable.
- Do not use near furnaces, fireplaces, stoves or other high temperature heat sources.
- The light source is not replaceable; when the light source reaches its end of life, the whole light shall be replaced.
DISPOSAL
- This product is made from high grade recyclable materials. Recycle where possible.
- Dispose in accordance with local ordinances or regulations.
WARRANTY
-
Terms and conditions: 1-year limited warranty (The warranty becomes effective from the
date of purchase or the date of delivery if this is later.) -
What is covered: The repair or replacement (at manufacturer’s discretion) if it is found to be defective due to faulty materials, workmanship or function within one year of purchase or delivery (If any part is no longer available or out of manufacture, the manufacturer will replace it with a functional replacement part.)
-
The warranty is only valid if the product is used in the country where it is originally purchased.
-
You must provide proof of delivery or purchase before any work can be carried out on your product. Without this proof, any work carried out will be chargeable. Keep your receipt or delivery note.
-
All work will be carried out by the manufacturer or its authorized agents.
-
Any parts which are replaced will become the property of the manufacturer.
-
The repair or replacement of your product under warranty will not extend the period of warranty.
WHAT IS NOT COVERED
The manufacturer does not warranty the repair or replacement of the product where a defect is the result of:
- Damage caused by not carrying out any recommended maintenance of the product
- Accidental damage, faults caused by negligent use or care, misuse, neglect, carelessness, operation or handling of the product which is not in accordance with the user manual
- Use of the product for anything other than the use it is designed for
- Use of parts not assembled or installed in accordance with the instructions of the manufacturer
- Use of parts and accessories which are not genuine components
- Faulty installation
- Repairs or alterations carried out by parties other than the manufacturer or its authorized agents
- Normal wear and tear (e.g. fuse etc.)
- End of life replacement is not covered under the warranty.
- If you are in any doubt as to what is covered by your warranty, please contact the helpline.
WIRELESS CHARGER
- Properly align mobile devices with the ʻ ’ symbol on the wireless charger.
- Heat can be generated depending on the charging status and mobile device.
- Remove smart phone case as thick case may prevent charging.
- Foreign objects such as metals, magnets, cards between charger and mobile device may prevent charging or cause damages.
- Frequency band: 110 kHz ~ 205 kHz
- Output power: below 37.7 dBuA/m at 10 m
FCC COMPLIANCE
-
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
-
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help. -
NOTICE: Any changes or modifications not expressly approved by the party responsible for compliance could void user’s authority to operate the equipment.
-
FCC Radio Exposure Information: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC ID: 2BFNPBNU-DL001
THE NEW LAMP
Baelux Co., Ltd.
82-4 Donggwang-ro, Seocho-gu, Seoul 06585, Korea
www.baenue.com
SUPPORT
help@baenue.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>