GIMA L100 Overbed Table User Guide
- June 1, 2024
- GIMA
Table of Contents
GIMA L100 Overbed Table
Specifications:
- Overall length : 640 mm
- Overall width : 406 mm
- Overall height (Tabletop at lowest position): 710 mm
- Horizontal static load : 25 kg
- Vertical static load : 25 kg
- Horizontal durability : 10 kg
- Vertical impact : 10 kg
- Net weight : 6.9 kg
- Gross weight : 8.2 kg
- Carton size : 650 x 64 x 670 mm
Product Usage Instructions
Assembling the Overbed Table:
- Open the end of the box and slide out the contents.
- Collect the base, top board, column assembly, hardware, and user manual.
- Place the column assembly on the base and install the base using M8 hex bolts with a 13mm wrench.
- Insert the lock bar into the horizontal tube and locate the gasket, then install the knob securely.
- Adjust the height of the table to the user’s comfort and fix it in place with the knob with a screw.
- Check the caster locks, release to move, and lock again when needed.
- Ensure caution when assembling to avoid touching sharp edges.
Using the Overbed Table:
- Release the knob with a screw to adjust the height of the table.
- Release the knob with a screw to lower or raise the board to desired height.
- Tighten all knobs securely after adjusting.
FAQ
- Q: What is the weight limitation of the L100 Overbed Table?
- A : The horizontal and vertical static loading limitation of the L100 is 25 kg (55 lbs).
- Q: What are the warranty terms for GIMA products?
- A: The GIMA products come with a 12-month standard B2B warranty.
OVERBED TABLE – Thank you for choosing this Overbed Table – L100.
General
Symbols
Signal words are used in this manual and apply to hazards or unsafe practices that could result in personal injury or property damage. See the information below for definitions of the signal words.
Warning – Warning indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury
Important – Indicates a hazardous situation that could result in damage
to property if it is not avoided.
Gives useful tips, recommendations, and information for efficient,
trouble-free use.
Safety
Check ALL parts for shipping damage. If shipping damage is noted, DO NOT use it. Contact carrier or dealer for further instruction.
Weight Limitation – The horizontal and vertical static loading limitation of the L100 is 25 kg (55 lbs).
General Warnings
DO NOT use this product or any available optional equipment without first completely reading and understanding these instructions and any additional instructional material such as owner’s manuals, service manuals or instruction sheets supplied with this product or optional equipment. If you are unable to understand the warnings, cautions or instructions, contact a healthcare professional, dealer or technical personnel
before attempting to use this equipment – otherwise, injury or damage may occur.
ALWAYS check the overbed table for proper tightness before using it.
The technical improvements of products will be compiled into the new version of the user manual without notice.
Accessories Warning
IDEAL products are specifically designed and manufactured for use in conjunction with IDEAL accessories. Accessories designed by other manufacturers have not been tested and are not recommended for use with IDEAL products.
Please in kind prevail if the appearance and color of products are changed
Installation Warning
ALWAYS use extreme caution when installing the column assembly, because it is with a sharp in the end of the horizontal tub, please don’t touch the sharp before completion of installation, otherwise injury or damage might occur. After any adjustments, repair or service and before use, make sure that all attaching component parts are secure.
Intended use
The overbed table as a kind of furniture is designed for use as a movable tabletop surface for reading, eating, or keeping small personal items such as glasses, telephone, or books within easy reach.
Parts (Packing) List
Assembling the Overbed Table ( Refer to the FIGURE 1)
- Open the end of the box and then slide the contents out of the box.
- Collect the base, top board, column assembly, hardware, and this user manual.
- Put the column assembly upon the base, then install bases one by one with an M8 hex bolt by 13mm wrench.
- Lock bar inserts into the horizontal tube and another side’s locating gasket, then install knob, finally insert into the tube of the table board and tighten the knob securely.
- Adjust the height of the table to the user’s comfortable position and then fix by a knob with the screw.
- Check the lock of the caster, release the lock to move, and lock on the contrary.
Please keep caution and DO NOT touch the sharp in the end of the hospital tube when assembled.
The overbed table is mainly composed of the following materials:
- Medium-density fiberboard (Tabletop)
- Steel Pipe (Table frame)
- Fastener (Screw, Nut, Knob)
- Plastic (Tube plug, Castor)
Using the Overbed Table ( Refer to the FIGURE 2)
- Release the knob with a screw to adjust the height and then tighten and fit when the table is at the desired height.
- Release the knob with a screw to let the board downward to the desired height or return to the original / lowest position, then tighten and fit.
This table is designed for use as a movable patient/resident table top surface
for reading, eating, or keeping small personal items such as glasses,
telephone, or books within easy reach. This table is designed for indoor use
ONLY within close proximity of skilled caregivers. It is not designed to hold
electrical items (such as televisions, computer monitors, coffee pots, etc.)
and should not be used near open flames and excessive heat.
The maximum weight limitation for this product is 25 kg (55 lbs); weight
should be evenly distributed over the tabletop surface to help maintain a
stable condition.
DO NOT overload the table as that could result in breakage, as well as damage to property and/or serious injury.
Use ONLY as directed for its intended use. This product should NOT be used: as a sleep surface; as a walker or mobility aid to assist a person in walking, sitting down or standing up; to prevent or brace a person’s fall; or to help transport persons or items.
Measurements (Unit: mm) ( Refer to the FIGURE 3)
Parameters
Cleaning
Regular care and maintenance will prevent unnecessary wear and damage to your overbed table.
Metal surfaces
Though the metal frame with high-quality powder coating to protect its surface, but for normal cleaning, it’s better to use a dry and soft cloth or sponge to wipe down.
Plastics
For normal cleaning, wash plastic surfaces with a soft cloth, mild detergent and water. Rinse thoroughly and dry with a soft cloth. Do not use solvents or abrasive kitchen cleaners.
Tabletop
Gently wipe the table with a soft, clean, damp cloth. Do not use cleansers that may damage the table’s finish. To wash more thoroughly, clean with mild soap and a little of water, and wipe up the water as soon as possible to keep the table top dry
GIMA WARRANTY TERMS
The Gima 12-month standard B2B warranty applies
Imported by:
Gima S.p.A.
Via Marconi, 1 – 20060 Gessate (MI) Italy
Made in China