MTI PADLOCK Smart Lock Kit Instructions

MTI PADLOCK Smart Lock Kit

Padlock Kit

Smartlock

BATTERY

Battery Caution

• Risk of fire or explosion if the battery is replaced by an incorrect type.
  • battery type: AAA (non-rechargeable)
  • chemical system of the battery: Alkaline

KEY REGISTRATION (Standard Mode) – Complete Before Use

1. Swipe Authorization card to enter enrollment mode. You will hear a double beep tone, indicating enrollment mode has been entered. 
2. Swipe each User card to lock. A double beep tone indicates a card is now enrolled. Repeat for each user card, up to 250 user cards. If a card fails to be recognized, the lock will emit 4 fast beeps.
3. Swipe Authorization card again to close enrollment mode. Enrollment mode times out after 3 minutes of no activity. Lock will emit 4 fast beeps when enrollment has timed out.

NETWORK MODE – Versa EX or Managed Access

1. Insert Intellikey into Connect® hub. After 10 seconds,  the System Status LED will be flashing blue, indicating it is in pairing mode. It will automatically time out after 15 minutes.
2. Swipe Pairing card to lock. Lock will start slowly beeping confirming it is looking for Connect ® network. Upon  successfully pairing the lock will emit a double beep. Lock will automatically download key whitelist from network. 

Full Connect Hub programming can be found in guide 063-00210

1. Place Pairing Card over the RFID icon to place Versa EX in pairing mode. LED will be flashing blue. 
2. Swipe Pairing card to lock. Lock will start slowly beeping confirming it is looking for Versa EX network. Upon successfully pairing the lock will emit a double beep. Lock will automatically download key whitelist from Versa EX.

Full Versa EX programming can be found in guide 063-00393

Using Padlock

1. Swipe Versa User Card on lock. Lock will emit double beep if card is accepted. 
2. Motor will cycle to unlock state. Shackle will pop open.
3. When finished, re-install lock to door latch and press shackle closed until you feel a click. Lock will emit a single beep when it is locked. If lock is not returned to locked position, it will start alarming after 5 minutes of being unlocked. 

Correct Disposal of Product
This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To dispose of used devices contact MTI Global Services Contact Center at 503-648-6500 or contact local recycling company for proper recycling instructions for electronic devices.

Powering lock with dead battery

1. Open battery door with hex too.
2. Insert USB-C from 5V USB-C power supply or external battery pack. We recommend MTI P/N 400-00186.
3. Upon powering up, wait 10 seconds to initialize lock.
4. Swipe RFID card and it will unlock the shackle.
   Leave battery plugged in until you have re-locked the door. Replace battery as soon as possible.

FCC Statement

FCC ID: 2AA2X-15000345
Model: Padlock

FCC STATEMENT
This device complies with Part 15 of the FCC Rules.

1. Operation is subject to the following two conditions:

2. This device may not cause harmful interference, and

3. This device must accept any interference received, including interference that may cause undesired operation.

4. Caution: If any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
   The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.

5. This transmitter must not be co-located or operating in construction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 2 centimeters between the radiator and your body.

NOTE:

• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
• However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

IC:24439-15000345
Model: Padlock

ISED Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference.
2. This device must accept any interference, including interference that may cause undesired operation of the device.

CAN ICES-3(8)/NMB-3(8)
The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 2 centimeters between the radiator and your body.

Technical Data

• Operating frequency 125KHz, 2.4GHz: 2405- 2480MHz
• Operating temperature: 0° C to 40° C
• Max power : 125KHz <42dBuNm at 10m, 2.4GHz < 20 dBm

www.mobiletechinc.com I T:800.426.6844
MTI P/N 063-00440 rev A ©2023 MTI All Rights Reserved

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>