Shelly Wi-Fi Smart Switch With Potential Free Contacts User Guide
- June 1, 2024
- Shelly
Table of Contents
USER AND SAFETY GUIDE
Wi-Fi smart switch with potential-free contacts
Shelly 1 Mini Gen3
Read before use
This document contains important technical and safety information about the
device, its safe use and installation.
⚠CAUTION! Before you start the installation, read carefully and entirely
this guide and any other documents accompanying the device. Failure to follow
the installation procedures can lead to malfunction, danger to your health and
life, violation of law, or refusal of legal and commercial guarantees (if
any). Shelly Europe Ltd. is not responsible for any loss or damage in case of
incorrect installation or improper operation of this device due to failure to
follow the user and safety instructions in this guide.
Product Description
Shelly 1 Mini Gen3 (the Device) is a small form factor smart switch with
potential-free contacts, which allows remote control of electric appliances It
can be retrofitted into standard electrical wall boxes, behind power sockets
and light switches, or in other places with limited space. The Device can be
accessed, controlled, and monitored remotely from any place where the User has
internet connectivity, as long as the device is connected to a Wi-Fi router
and the Internet.
The Device has an embedded web interface that you can useto monitor, control
the Device, and adjust its settings. The web interface is accessible at
http://192.168.33.1 when you are connected directly to the Device access
point or at its IP address when you and the Device are connected to the same
network.
⚠NOTICE: The Device comes with a factory-installed firmware. To keep it
up-to-date and secure, Shelly Europe Ltd. provides the latest firmware updates
free of charge. You can access the updates through either the embedded web
interface or the Shelly Smart Control mobile application, where you can find
details about the latest firmware version. The choice to install or not the
firmware updates is the user’s sole responsibility. Shelly Europe Ltd. shall
not be liable for any lack of conformity of the Device caused by the failure
of the user to install the available updates in a timely manner.
Schematic
Legend
Device terminals:
-
SW: Switch input terminal
-
O: Relay output terminal
-
I: Relay input terminal
-
L: Live (110-240 VAC) terminal
-
N: Neutral terminal
Wires: -
N: Neutral wire
-
L: Live (110 – 240 VAC) wire
Installation Instructions
⚠CAUTION! Danger of electrocution. Mounting/installation of the Device to
the power grid has to be performed with caution, by a qualified electrician.
⚠CAUTION! Danger of electrocution. Every change in the connections has to
be done after ensuring there is no voltage present at the Device terminals.
⚠CAUTION! Do not use the device if it shows any sign of damage or defect.
⚠CAUTION! Do not open the device. It does not contain any parts that can
be maintained by the user. For safety and licensing reasons, unauthorized
change and/or modification of the device is not permitted.
⚠CAUTION! Use the Device only with a power grid and appliances that
comply with all applicable regulations. A short circuit in the power grid or
any appliance connected to the Device may damage it.
⚠CAUTION! No SELV/PELV circuits may be connected to the terminals of the
inputs and outputs, including the extension inputs.
⚠CAUTION! Do not connect the Device to appliances exceeding the given max
load!
⚠CAUTION! Connect the Device only in the way shown in these instructions.
Any other method could cause damage and/or injury.
⚠CAUTION! The Device is intended for indoor use only.
⚠CAUTION! Keep the Device away from liquids and moisture. Do not use the
device in places with high humidity.
⚠CAUTION! The Device can control electric circuits and ap- pliances
wirelessly. Proceed with caution! Irresponsible use of the Device may lead to
malfunction, danger to your life, or violation of the law.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>