Saifun 5031 7 In 1 Keyless Entry Door Lock Instruction Manual

Smart Door Lock
Installation Instructions

Instruction Manual

INCLUDED IN THE BOX

OPERATION TESTING

PREPARING TO INSTALL

Disassemble your existing deadbolt from the door.

STEP 1 PREPARATION

STEP 2 INSTALLING LATCH AND STRIKE PLATE

STEP 3 PREPARING KEYPAD

STEP INSTALLING KEYPAD

STEP INSTALLING MOUNTING PLATE

STEP 6 PREPARING INTERIOR ASSEMBLY

Make sure the switch and the knob are set to correct door handing

STEP 7 CONNECT THE CABLE

STEP 8 INSTALLING INTERIOR ASSEMBLY AND TESTING

STEP 9 BACK UP KEY TESTING

STEP 10 INSTALLING BATTERIES & COVER

Function introductions

1. Unlocking mode
   TTLOCK app, Fingerprint unlocking, Password unlocking, Card unlocking, Emergency key unlocking (emergency condition only).

2. System capacity

   ---

3. Initial state
   This product adopts the classification permission management. The type of users could divided into administer user and ordinary user. Administrator user has the maximum authority while ordinary user only have door opening authority. At initial state, the administrator password is “123456 ” , please timely modify the initial administrator password,

4. Operating rule
   1. Key is the “enter or unlock” key. After enter the password, press to unlock.
   2. Key is the lock button, Press Key to lock the door.
   3.This product contain password, fingerprint and card function. There are 6-9 digits valid for password, and it is supporting scramble pin code.

5. Factory reset
   Long press the RESET button, after hearing two short beeps, the lock will recover to the factory setting and delete all the fingerprint , password, card and cellphone administer.

6. Add administer password
   When the administrator password is not set, or the mobile phone administrator is not added, enter “ 12 123456 ” , after that enter 6-12 digit administrator code, press “ ” Key to confirm and enter again, if the two password are the same, the operation successful. Attention: to set administrator pass code in the app, choose lock on the application >click settings>click basics>click admin pass code

7. Add administer app Touch the keyboard to wake up the lock before adding bluetooth administrator in the App. The lock will give a long beep when the operation is successful. If the administrator pass code or bluetooth administrator is set, enter “ 83 administrator pass code ” to reenter setting mode. *Note: In this mode, another App account is allowed to add the lock. The user’s fingerprints, password and card information before adding the app will be automatically deleted. The administrator password is still available.

8. Administrator password modification Enter “ 12 ” and then enter original pass code, after that press “ ” Key to confirm, then press new password and press “ ” Key to confirm and enter again. If the two new password are the same, the operation successful.

9. Add password user Enter “ 85 ” , after hearing two short beeps, enter “administrator pass code ” , if the pass code is correct, will hearing two short beeps, and then enter “new pass code ” , if the operation successful will hearing a long beep. If operation failed will hearing four short beeps. After add password user successful, could continue to add other password user or press “ ” Key or waiting until exit the add mode.

10. Delete password user
    Enter “ 71 ” administrator password ” to delete all the password user. (Except administrator password).

11. Password modification
    Enter “ 10 original pass code new pass code new pass code again ” . (Modify administrator pass code, please enter’ 12 original pass code new pass code new pass code again ” . )

12. Add fingerprint user
    Enter “ 85 administrator password ” , after hearing two short beeps, put finger and add fingerprint 3 times. If it is same fingerprint, the operation is successful. And then you could add other fingerprint user or press “ ” Key or waiting until exit add mode.

13. Delete fingerprint user
    Enter “ 70 administrator pass code ” , all fingerprint users will be deleted.

14. Add card user
    Enter “ 80 administrator pass code ” , if the administrator pass code is correct, swiping card to add card user.

15. Delete card user
    Enter “ 69 administrator pass code ” , all the card users will be deleted.

16. Other instruction
    1.If verifying unsuccessful for more than 5 consecutive times, the keyboard will be locked for 5 minutes automatically. After 5 minutes, will unlock the keyboard. During the disabled lock state, verify fingerprint user or IC card user or cellphone application user could release keyboard lock state.
    2.The scramble Pin code is available for the smart lock. For example, your setting password is 123456, it is possible to open the lock if you enter the password 00001234560000, it has 16 digits in total for scramble pin code and valid password together, and this function could prevent peeping.
    3,If the voltage of the battery is lower than 4.8V, the keyboard light will flash for 1 second when the keyboard is awaken. The keyboard light will flash for 1 second before the door is unlocked via fingerprint/IC card/password. (Please replace the battery after)

17. Emergency power
    When the smart lock is out of power or the battery do not have enough power to open the lock, USB power is available. The position of emergency power interface is showed in product detailed drawing in second page. the system could be activated to open the door normally. (Please replace the battery after)

Two Methods to Contact After-Sales:
Thank you for purchasing, If you have any questions about the products you’ve received, don’t hesitate to contact us by following methods. We will provide you with satisfactory service and help solve he problem.

Method 1:
Contact us through Amazon :
“Your order”>>”sold by” >>
“Ask a question”>>”An order I have placed”

Method 2:
Contact us through Email:
RSS-Service@outlook.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>