hansgrohe 74532000 AXOR Metropol Single Lever-Bath Mixer Floor-Standing Instruction Manual

hansgrohe 74532000 AXOR Metropol Single Lever-Bath Mixer Floor-Standing

Product Information

Specifications

• Model: Metropol 32532XXX
• Max Pressure: 1 MPa
• Operating Pressure Range: 0.1 – 0.5 MPa
• Max Temperature: 1.6 MPa (1 MPa = 10 bar = 147 PSI)

Product Usage Instructions

Safety Notes

• Always wear gloves during installation to prevent crushing and cutting injuries.
• The product is intended for bathing, hygienic, and body cleaning purposes only.
• Do not load the shower arm with other objects, it is designed to hold the shower head only.
• Ensure proper supervision for children and individuals with impairments when using the product.
• Avoid letting the shower streams touch sensitive body parts and maintain a safe distance.

Installation Instructions

• Make sure the hot and cold water supplies have equal pressures to avoid issues.
• Use caution during installation to prevent dirt from entering the pipework, which can cause defects or damage.

FAQ

• Issue: Low Water Flow
  • Cause: Drossel in the hand shower not removed, Sieve seal of the shower head dirty.
  • Solution: Clean the sieve seal between the shower head and hose, replace the cartridge if needed.
• Issue: Dripping Faucet
  • Cause: Drossel in the hand shower not removed, Sieve seal of the shower head dirty.
  • Solution: Clean the sieve seal between the shower head and hose, remove the drossel from the hand shower.

Safety Notes

• Gloves should be worn during installation to prevent crushing and cutting injuries.
• The product may only be used for bathing, hygienic and body cleaning purposes.
• The arm of the shower head is intended only to hold the shower head. Do not load it down with other objects!
• Children as well as adults with physical, mental and/or sensoric impairments must not use this product without proper supervision. Persons under the influence of alcohol or drugs are prohibited from using this product.
• Do not allow the streams of the shower touch sensitive body parts (such as your eyes). An adequate distance must be kept between the shower and you.
• The product may not be used as a holding handle. A separate handle must be installed.
• The hot and cold supplies must be of equal pressures.

Installation Instructions

• Prior to installation, inspect the product for transport damages. After it has been installed, no transport or surface damage will be honoured.
• The pipes and the fixture must be installed, flushed and tested as per the applicable standards.
• The plumbing codes applicable in the respective countries must be observed.
• The mesh washer must be insert to protect the shower against incoming dirt by pipework. Incoming dirt leads to defects or/and can damage parts of the shower; such caused faults voids all liability and guarantee claims.

Technical Data

• Operating pressure: max. 1 MPa
• Recommended operating pressure: 0,1 – 0,5 MPa
• Test pressure: 1,6 MPa (1 MPa = 10 bar = 147 PSI)
• Hot water temperature: max. 60°C
• Centre distance: 150±12 mm
• Connections G 1/2: cold right – hot left
• Thermal disinfection : 70°C / 4 min
  • Safety against backflow
  • The product is exclusively designed for drinking water!

Symbol description

Adjustment
To adjust the hot water limiter. Using a hot water limiter in combination with a continuous flow water heater is not recommended.

Maintenance
The check valves must be checked regularly according to EN 806-5 in accordance with national or regional regulations (at least once a year).

Dimensions

Flow diagram

Spare parts

• XXX = Colors
• 000 = Chrome Plated
• 140 = Brushed Bronze
• 340 = Brushed Black Chrome
• 670 = Matt Black
• 700 = Matt White
• 990 = Polished Gold-Optic

Cleaning
Just clean: simply rub over the spray nozzles to remove lime scale.

Hot and cold supplies are reversed

Test certificate

TROUBLESHOOTING

shower and hose
Mixer stiff| – Cartridge defective, calcified| – Exchange cartridge
Mixer dripping| – Cartridge defective| – Exchange cartridge
Spout temperature does not correspond with tempera-

ture set

| – Hot and cold supplies are reversed| – Install function block turned through 180° (see page

Instantaneous heater didn’t work| – Flow limiter in handshower isn’t removed| – Remove flow limiter
 | – Shower filter seal dirty| – Clean filter seal between shower and hose

Assembly

References

• Taps for bathrooms, showers and kitchens
• Banyo ve mutfak için musluk ve armatürler

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>