INTERCOA ETP-01T-R Single Port Ethernet over Coax Transmitter / Receiver User Guide
- June 1, 2024
- INTERCOA
Table of Contents
- INTERCOA ETP-01T-R Single Port Ethernet over Coax Transmitter / Receiver
- Package
- Hardware Overview
- LED Indicators
- Overview
- Features
- Installation Guide
- Application
- Specification
- Warranty
- Read More About This Manual & Download PDF:
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
INTERCOA ETP-01T-R Single Port Ethernet over Coax Transmitter / Receiver
User Guide
Package
Hardware Overview
LED Indicators
Overview
ETP-01 Series are High-Speed, long distance Ethernet & PoE extender that makes
possible to transmit the Ethernet signal and PoE up to 300m through single
pair of twisted wires.
It is cost-effective and time saving solution to migrate existing analog
system to IP based system since ETP-01 series support easy installation
utilizing the existing UTP bundle cables or any single twisted pair cables.
With long distance transmission feature, the device makes to overcome 100
meters distance limitation easily and reduces the construction cost
significantly compared with fiber optic configuration.
Features
Long reach Ethernet & PoE extension over existing 2-Wire twisted cable
? Data + Power over twisted cable
? Data and PoE distance up to 300 m
? 100Mpbs Full Duplex
? PoE, PoE+, Extra PoE (Max. 60W PoE output, ETP-01T model only with DC Power
adapter)
? LED Indication (Data, Power)
? Plug & Play
? Surge Protection
Installation Guide
-
Connect Ethernet cable (Cat5e or better) from PoE Switch/NVR to ETP-01R. Check LEDs on ETP-01R.
-
Connect single twisted pair cable to ETP-Connect single twisted pair cable from ETP-01R to ETP-01T.
-
Connect Ethernet cable (Cat5e or better) from ETP-01T to IP Camera. Check LEDs on ETP-01T
Set ETP-01T, PoE Switch ON to supply direct power to IP camera. Set ETP-01T, PoE Switch OFF to connect PC or network switch devices
Application
Simply IP and PoE over 2-Wire]
[High Power over 2-Wire]
[Extra PoE (60W) over 2-Wire]
Specification
Model ETP-01T ETP-01R
Interface
| ****
2-Wire
| 1 x 2-Pin Terminal Block– Ethernet over 2-Wire cable
Ethernet| 1 x RJ45 – 100 Base-T
Transmission Rate
| 100Mbps Full Duplex (100Mbps between Intercoax devices)
Transmission Distance
| Ethernet| Up to 300m (1 Pair of Cat.5e)
PoE (PoC)| Up to 300m (1 Pair of Cat.5e / 7W Camera)
LED
Indication
| ****
Ethernet
| ****
1 x Link (Yellow) / 1 x ACT (Green)
Power
| ****
Input
| ****
T-Linx or DC48V~57V
| PoE Switch or DC48V~57V
PoE Output
| IEEE802.3af (PoE), IEEE802.3at (PoE+),
Extra PoE up to 60W with 57V Power Adaptor
| ****
PoE Not Supported PoC Only
Mechanical
| Dimension| 93(L) x 51(W) x 24(H)mm
Weight| 52 g
Environment
| Operating Temp| ****
-20 ~ 60°C
Storage Temp| ****
-30 ~ 80°C
Relative Humidity| ****
10% ~ 90%
Compliance
| Certification| FCC, CE, KC, RoHS
Surge Protection| IEC 61000-4-5 4kV(1.2 / 50us),
2kA(8 / 20us)
Optional Accessories| 57VDC / 1.2A External Power Supply
Caution
- Please install the device following the installation guide.
- Do not touch the device and cable with wet hands.
- Keep away from moisture and shock.
- Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus that produce heat
- Indoor use only. (Use waterproof junction box when it is used in outdoor)
- Do not use for other purposes.
- Do not disassemble or modify this device.
- Do not put any sticker or paint on it.
- If this device is defective or malfunctioning, please unplug the power source immediately and contact dealer or service center.
- Please use the rated power supply for the product.
- Connect DC power to this device first and then to AC outlet when using DC power supply.
Warranty
This device has passed the quality control and product inspection.
Please install and use according to the installation guide.
The warranty period for this product is 24 months from the date of purchase.
If this device is defective or malfunctioning, please unplug the power adapter
immediately and contact dealer or service center.
Any damages or breakage from user’s abuse, accident, modification or natural
disasters will not be covered manufacturer’s warranty
This device complies with part 15 of the fcc rules. Operation is subject to the following two conditions :
- This device may not cause harmful interference, and
- This device must accept any interference received including interference that may cause undesired operation