Fande-Aire BL-2542 5 Blades +6Leds 56 inch Large Ceiling Fan Instruction Manual

Fande-Aire BL-2542 5 Blades +6Leds 56 inch Large Ceiling Fan

Specifications

• Product Name: Ballet Ceiling Fan
• Size: 56-inch Large Ceiling Fan
• Blades: 5 Blades
• Lighting: 6 LEDs
• Model Number: BL-2542
• Design: Double Layer Design

Product Usage Instructions:

Safety Precautions

1. Before starting any installation process, ensure that the electricity is turned off at the circuit breaker or fuse box.
2. All wiring should comply with the National Electrical Code ANSI/NFPA 70-1999 and local electrical codes. Installation must be done by a qualified electrician.
3. Ensure that the outlet box and support structure can support the fan’s weight of 35 lbs. securely.
4. Install the fan at a minimum height of 7 feet above the floor to prevent injury.

Installation

1. Ensure the outlet box is securely installed to support the fan weight.
2. Avoid bending the blade brackets during assembly or installation and remove any rubber motor stops before installing blades.
3. Do not use solid-state speed controls with this fan to prevent fire or electric shock risks.
4. Operate the reversing switch only when the fan blades are stationary.

Cleaning and Maintenance

1. Exercise caution when cleaning or working around the fan to avoid personal injury or damage to the fan.

Electrical Connections

1. Ensure proper electrical connections are made following guidelines for grounded and ungrounded conductors.
2. Spliced conductors should be carefully pushed into the outlet box after making electrical connections.

Frequently Asked Questions (FAQ)

• Q: Can I use a solid-state speed control with this fan?
  A: No, this fan is not suitable for use with solid-state speed controls as it may pose risks of fire or electric shock.

• Q: How high should I install the fan above the floor?
  A: Install the fan so that the blade is at least 7 feet above the floor to reduce the risk of injury.

• Q: Can I clean the fan blades while they are in motion?
  A: No, do not operate the reversing switch while the fan blades are in motion. Make sure to turn off the fan and stop the blades before reversing their direction.

Instruction Manual
No. BL-2542
Double Layer Design

SAFETY PRECAUTIONS

1. To reduce the risk of electric shock, ensure the electricity has been turned off at the circuit breaker or fuse box before you begin.

2. All wiring must be in accordance with the National Electrical Code ANSI/NFPA 70-1999 and local electrical codes. Electrical installation should be performed by a qualified licensed electrician.

3. The outlet box and support structure must be securely mounted and capable of reliably supporting 35 lbs. (15.9 kg).
   Use only UL Listed outlet boxes marked “Acceptable for Fan Support of 35 lbs. (15.9 kg) or less”.

4. Caution:To Reduce The Risk Of Injury To Persons, Install Fan So That The Blade Is At Least 2.1 Meters (7 Feet) Above The Floor.

5. After installation is complete, please check that the outlet box is securely installed in place such that it is able to support at least the fan weight.

6. Do not operate the reversing switch while the fan blades are in motion. You must turn the fan off and stop the blades before you reverse the blade direction.

7. Do not place objects in the path of the blades.

8. To avoid personal injury or damage to the fan and other items, use caution when working around or cleaning the fan.

9. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be Ul-listed and marked suitable for use with the model fan you are installing. Switches must be UL General Use Switches.Refer to the instructions packaged with the light kits and switches for proper assembly.

10. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into the outlet box. The wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box.

11. Supply connections: conductor of a fan indentified as grounded conductor to be connected to a grounded conductor of power supply, conductor of fan identified as ungrounded conductor to be connected to an ungrounded conductor of power supply, conductor of fan identified for equipment grounding to be connected to an equipment-grounding conductor.

12. All set screws must be checked and re-tightened where necessary before installation.

READ AND SAVE THESE INSTRUCTIONS

CAUTION: To Reduce The Risk Of Electric Shock, Disconnect The Electrical Supply Circuit To The Fan Before Installing Light Kit.
WARNING: To reduce the risk of personal injury, do not bend the blade brackets (also referred to as flanges) during assembly or after installation. Do not insert objects in the path of the blades.
WARNING: Remove the rubber motor stops on the bottom of the fan before installing the blades or testing the motor
WARNING: To reduce the risk of fire or electric shock, this fan is NOT suitable for use with solid-state speed controls.
WARNING: Electrical diagrams are for reference only. Optional use of any light kit shall be UL-listed and marked suitable for use with this fan
WARNING: To reduce the risk of fire, electrical shock or personal injury, ensure that the fan mounting bracket is supported directly from the building structure or the outlet box marked
“Acceptable for Fan Support of 35 lbs. (15.9 kg) or less”. Use only the screws provided with the outlet box.

TOOLS AND MATERIALS REQUIRED

• Philips screw driver
• Blade screw driver
• 11 mm wrench
• Step ladder
• Pliers

PACKAGE CONTENTS / THE CEILING FAN ELEMENT

Unpack your fan and check the contents. You should have the following items:

1. Mounting bracket *1
2. Canopy *1
3. Hanger ball *1
4. Downrod * 2
5. Horn cover *1
6. Receiver *1
7. Remote *1
8. Blade *5
9. DC motor *1
10. Lamp supporting *1
11. Led light arm *5
12. Screw bolt *1（Installed on the motor shaft）
13. Terminal box *1
14. LED light source plate *1
15. Lampshade *1

MOUNTING OPTIONS

• If there isn’t an existing UL (cUL for Canadian Installation) listed mounting box, then read the following instructions. Disconnect the power by removing fuses or turning off circuit breakers.
• Secure the outlet box directly to the building structure. Use appropriate fasteners and building materials. The outlet box and its support must be able to fully support the moving weight of the fan (at least 50 lbs). Do not use plastic outletboxes.
• Figures 1,2 and 3 are examples of different ways to mount the outlet box.
• NOTE : If you are installing the ceiling fan on a sloped (vaulted) ceiling, you may need a longer down rod to maintain proper clearance between the tip of the blade and the ceiling. A minimum clearance of 12″ is suggested for optimal operation.
• NOTE : Depending on the location you have selected for installation, you may need to purchase and install a “Joist Hanger” for the support of the outlet box. Make sure the joist hanger you purchase has been designed for use with ceiling fans. (Fig. 4)

INSTALLATION OF THE CEILING FAN

1. Install the mounthing bracket by screws. Refer Fig 1.
   NOTE : Before starting installation, disconnect the power by turning off the circuit breaker or removing the fuse at fuse box.

2. Attaching the fan blades:

3. Step 1: Remove 15 preassembled screws and fiber washer from blade bracket, and save it for later use, then insert blade through one of the slots from the flywheel. Align holes from blade bracket and blade and secure with just moved screws and fiber wahser.Refer Fig 2, tighten each screws.

4. Step 2 : Repeat for the remaining blades.

5. Step 3 : Make sure the blade is straight and tighten each screw.

6. Insert downrod over canopy, then insert the cross pin over yoke & Cotter pin and fasten the screws which fix the downrod.Refer Fig 3.

7. Hang the fan and assemble the receiver with power.

8. Step1: Carefully hang the fan with blades into the mounting bracket. Rotate the down rod till the notch of the hanger ball engages the pin of the mounting bracket.

9. Step 2 : Then insert the remote control receiver in the mounting bracket. Connect the motor and light kit wires with receiver by male & female connectors.Then connect the power supply wires with the fan by wiring cap. Also, connect the ground wire by wiring cap.Refer Fig 4.

10. Assemble the lamp arms to the lamp supporting:

11. Step 1 : Remove 5 preassembled screws and washer from lamp arms,and save it for later use, then insert lamparm through one of the slots from the lamp supporting and secure with just moved screws and wahser.Refer Fig 5, tighten each screws.

12. Step 2 : Repeat for the remaining lamp arms.

13. Step 3 : Make sure the direction of each lamp arm is same and tighten each screw.

14. Step 4 : The wire of each arm runs through the corresponding round hole.

15. Step 5 :Install the whole lamp supporting which with lamp arms to the fan body by screws.

16. Assemble light source and connect the wires:

17. Step 1 :Install the bolt onto the motor shaft and remove a nut to secure the light source board

18. Step 2 : Connect the wires from LED light source plate, lamp arms with the wires from driver. Refer Fig 6.
    NOTE : There are total 8 terminal boxes on the connect panel. One is connecting with LED driver, the other 7 are for LED light source plate and lamp arms. When connecting the wires, just insert the wiries into the connect boxes, you can use 6 randomly of these 7 ones. Please refer the right figure.

19. Assemble the LED light source plate into the lamp supporting. Refer Fig 7.

20. Install the acrylic shade.Put the acrylic shade into the metal ring. Fig 8.

21. Now, the fan is completed. Please connect the power, test and enjoy each function of the fan.Thank you! Refer Fig 9.
    Note : Consumers need to purchase 3A batteries themselves

Operation for remote

KINDLY REMINDER
Learning code matching mode is used between emitter and receiver.
Turn “On” the supply power within 5 seconds and press the emitter’s “FAN ON/ OFF” button for 3 seconds, it can load normally after hearing a long sound” bee”, which means learning successfully and it can work normally. (PS:Learning mode is not accepted after turn ON the supply power for 30 seconds) Button function instruction

• ① LED indicated light
• ② ON/OFF the light
• ③ OFF the fan
• ④ Speed of the fan (①low speed —
• ⑥high speed)
• ⑤ Direction of the fan (reverse switch)
• ⑥ Natural wind
• ⑦ Simulate a human burglar lamp
• ⑧ Delay closing of the fan
• ⑨ Timing control of the fan

Dimmable Remote

Operation for remote

Wiring diagram

Note:Please connect relevant components strictly following instructions on the label. Otherwise switch life will be influenced directly and the switch will fail to function.

1. The fan switch must be on status, and our product can control fan.
2. When the emitter can not control the receiver,please check whether batteries touch is normal,the placed of anode and cathode is correct and power is enough.
3. Please use product in allowable voltage,it is not normal if the voltage is too low.(Please check the label for voltage range and correlative technique parameter.)
4. When the emitter can not control the receiver, please check if there are similar remote control products existing the nearby range,and check whethertheir launcher buttons are pressed,because remote control products with the same properties launching electric wave at the same time,will cause mutual interference and influencethe receiving effect;and that will be normal again after the remote control function is eliminated.(Exclude the remote control)
5. Please take out the batteries when not use in a long time.
6. Requirements for each load: bulb^300W; fan^120W.

OPERATION AND MAINTENANCE

Operation:
Turn on the power and check operation of fan. The pull chain controls the fan speeds as follows: 1 pull – high; 2 pulls – medium; 3 pulls – low; 4 pulls – off.
Speed settings for warm or cool weather depend on factors such as room size, ceiling height, number of fans and so on. The slide switch controls direction, forward or reverse.
Warm weather/down position – (Forward) Fan turns counterclockwise direction. A downward air flow creates a cooling effect as shown in illustration A. This allows you to set your air conditioner on a higher temperature setting without affecting your comfort.
Cool weather/up position – (Reverse) Fan turns clockwise direction. An upward airflow moves warm air off the ceiling area as shown in illustration B.
This allows you to set your heating unit on a lower setting without affecting your comfort.
(Please however refer to point 10 in Safety Tips when operating in this position.) NOTE: Turn off and wait for fan to stop before changing the setting of the forward/reverse slide switch.

Maintenance

1. Because of the fan’s natural movement, some connections may become loose. Check the support connections, brackets, and blade attachments twice a year. Make sure they are secure.
2. Clean your fan periodically to help maintain its new appearance over the years. Do not use water when cleaning. This could damage the motor, or the wood, or possibly cause electrical shock.
3. Use only a soft brush or lint-free cloth to avoid scratching the finish. The plating is sealed with a lacquer coating to minimize discoloration or tarnishing.
4. There is no need to oil your fan. The motor has permanently lubricated bearings.

TROUBLESHOOTING GUIDE

FAN DOES NOT WORK

• Check all fuses or circuit breakers. Replaceif missing.
• Turn off electrical power and check all check all wire connections to fan and in switch housing.

FAN IS NOISY

• Always allow a few days “break in” time for any new fan at medium or high speed. Try to diagnose the exact location of the noise by listening carefully from several sides (blades, motor, light kit, etc.) Fan noise can come from a light kit.
• Make sure all screws in the fan assembly and light kit are tight and properly threaded. If not, back out and retighten. Tighten these screws at least once a year because they may loosen slowly over time and cause a clicking noise.
• Make sure the light kit is securely fastened to the fan, and all glass screws are finger tightened only. Do not tighten with pliers or a screwdriver.
• Make sure mounting bracket is installed snugly to junction box.
• Make sure wire nuts in switch housing or canopy are not rattling against each other or against wall of housing. Wrap with electrical tapeif necessary.
• Use of standard light rheostat or unapproved wall control will always cause harmonic distortions, or a humming noise. Many fan motors do no work quietly with solid state variable controls. If a quiet wall control is desired, use only approved wall controls.
• Make sure the canopy is not touching the ceiling.
• Assure that the screws fastening the blade holders to the motor are tight and the lock washers provided for that purpose have been used.
• If applicable, make sure all light bulbs are fully screwed in.

FAN TURNS BUT DOES NOT MOVE MUCH AIR:

• The fan may be running in reverse, so air is directed upward.
• The room may contain items that obstruct the airflow.
• The fan may be too small for size of the room.

FAN SHAKES OR WOBBLES:
A small amount of wobble is considered acceptable and should not be considered a defect. Use of any light kit, especially a large 4 or 5 light kit will usually induce some wobble.

• Make sure the mounting bracket is tight at junction box/ceiling with no movement at all. Tighten screws if necessary.
• Make sure all screws holding the blades to the blade arm and blade arm to motor are tight.Make sure light kit/glass screws are tight.
• Some fan movement is normal. However, interchanging an adjacent(side-by-side) blade pair may redistribute the weight and result in smoother operation.
• If a balancing kit is provided, use it if needed

UNIQUE
Continuous innovation is the soul of product design

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>