DUMOS D-L02-49IN Shaped Computer Desk Wood Corner PC Gaming Table Instruction Manual

L Shaped Computer Desk
Instruction Manual
D-L02-49IN HJ- Customer-Service@outlook.com
(909)637-7665 | (909)637-7593
EST 9:00AM–17:00PM

Component List

Supplied Parts and Hardware

ATTENTION:

1. Please do not wipe the desk with corrosive liquids.
2. Please keep the parts properly to avoid contact and accidental ingestion by children.
3. Please do not place overheated kitchenware and cutlery to avoid damage to the table.

Step 1

Use the Wrench ⑥ and Screws ① 4 to connect the Crossbeam G 2 and Legs E 1 and F 1 respectively.
NOTE: Note the Orientation of Crossbeam G holes.
Step 2

Connect the Crossbeam I 1 to the Legs F 1 and D 1 using the Wrench ⑥ and Screws ① 2.
NOTE:

1. The orientation of hole I on the crossbeam.
2. The hole orientation for legs F and D.

Step 3

First, connect Bar L1 and Leg F1 and D1 respectively with Wrench ⑥ and Screw ②4, and then tighten the center screw of Bar L*1 by 100%.
Step 4

Use Wrench ⑥ and Screw ①2 to connect Crossbeam H1 and Crossbeam I1 and Leg E1 respectively.
NOTE:

1. The screws are only tightened by 50%.
2. Pay attention to the orientation of the H-hole on the crossbeam.

Step 5

First, connect Bar K1 and legs E1 and F1 respectively with Wrench ⑥ and Screw ②4, and then tighten the center screw of Bar K*1 by 100%.
Step 6

Use the Wrench ⑥ and Screws ① 5 to connect Table A 1 and Legs F 1 and D 1 respectively.
NOTE:

1. The screws are only tightened by 50%.
2. Ensure that the frame structure is flush when installing the desktop board.

Step 7

Use Wooden Pins ④2 as well as Wrench ⑥ and Screws ①5 to connect Table Board B1 and legs E1 and F1 respectively, using Hole Stickers ⑦2 to cover the exposed screw holes in the plate.
NOTE:

1. The screws are only tightened by 50%.
2. Ensure that the frame structure is flush when installing the desktop board.

Step 8

First, use Wrench ⑥ to unscrew the screws attached to the top of Leg E and Crossbeam H. Then use Wrench ⑥ and Screw ①2 and Nut ③1 to attach the Felt Bag M1 to Leg E. Use Wrench ⑥ and Screw ①2 to connect the Tabletop C1 and Leg J2. Finally, use Wrench ⑥ and Screw ⑤2 again to attach Tabletop C1 to either side of either of the two legs (E and F).
Step 9

Tighten all screws in steps 4, 6, and 7 from 50% to 100% and fully lock them.
NOTE:
Make sure all Bolts are 100% tightened before use.

You can choose another installation method customize the placement as your habit.
Step 1

Use the Wrench ⑥ and Screws ① 4 to connect the Crossbeam G 2 and Legs E 1 and F 1 respectively.
NOTE: Note the Orientation of Crossbeam G holes.
Step 2

Connect the Crossbeam I 1 to the Legs F 1 and D 1 using the Wrench ⑥ and Screws ① 2.
NOTE:

1. The orientation of hole I on the crossbeam.
2. The hole orientation for legs F and D.

Step 3

First, connect Bar L1 and Leg F1 and D1 respectively with Wrench ⑥ and Screw ②4, and then tighten the center screw of Bar L*1 by 100%.
Step 4

Use Wrench ⑥ and Screw ①2 to connect Crossbeam H1 and Crossbeam I1 and Leg E1 respectively.
NOTE:

1. The screws are only tightened by 50%.
2. Pay attention to the orientation of the H-hole on the crossbeam.

Step 5

First, connect Bar K1 and legs E1 and F1 respectively with Wrench ⑥ and Screw ②4, and then tighten the center screw of Bar K*1 by 100%.
Step 6

Use the Wrench ⑥ and Screws ① 5 to connect Table A 1 and Legs F * 1 and D

• 1 respectively.
  NOTE:

  1. The screws are only tightened by 50%.
  2. Ensure that the frame structure is flush when installing the desktop board.

Step 7

Use Wooden Pins ④2 as well as Wrench ⑥ and Screws ①5 to connect Table Board B1 and legs E1 and F1 respectively, using Hole Stickers ⑦2 to cover the exposed screw holes in the plate.
NOTE:

1. The screws are only tightened by 50%.
2. Ensure that the frame structure is flush when installing the desktop board.

Step 8

First, use Wrench ⑥ to unscrew the screws attached to the top of Leg E and Crossbeam H. Then use Wrench ⑥ and Screw ①2 and Nut ③1 to attach the Felt Bag M1 to Leg E. Use Wrench ⑥ and Screw ①2 to connect the Tabletop C1 and Leg J2. Finally, use Wrench ⑥ and Screw ⑤2 again to attach Tabletop C1 to either side of either of the two legs (E and F).
Step 9

Tighten all screws in steps 4, 6, and 7 from 50% to 100% and fully lock them.
NOTE: Make sure all Bolts are 100% tightened before use.

Technical Support
(909)637-7665 | (909)637-7593
Other Info
HJ-Customer-Service@outlook.com
Thank you for choosing this product. We strive to provide you with the best quality products and services in the industry. Should you have any issues, please don’t hesitate to contact us.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>