DUMOS ELT-Z4024 Standing Desk with Whole Piece Desktop Board Instruction Manual
- June 16, 2024
- DUMOS
Table of Contents
DUMOS ELT-Z4024 Standing Desk with Whole Piece Desktop Board
Specifications:
- Model Numbers: ELT-Z4024, ELT-Z4824, ELT-Z5524, ELT-Z6324
- Email: HJ-Customer-Service@outlook.com
- Phone: (909)637-7665 | (909)637-7593
- Operating Hours: EST 9:00 AM–5:00 PM
Product Information
Thank you for choosing our Electric Standing Desk. We are committed to providing you with the highest quality products and services. Please read the following instructions carefully before using the desk.
Product Usage Instructions
Assembly:
- Unpack all the components of the desk.
- Attach the legs to the tabletop using the provided screws.
- Tighten all 6 screws on the crossbeam to ensure stability.
Height Adjustment:
- Connect the power cord to a power outlet.
- Use the control panel located on the side of the desk to adjust the height.
- Press the up or down arrow buttons to raise or lower the desk respectively.
- Release the button once you reach your desired height.
Safety Precautions:
- Do not overload the desk with excessive weight.
- Avoid placing objects near the moving parts of the desk.
- Keep liquids away from the control panel to prevent damage.
- Do not attempt to disassemble or repair the desk without professional assistance.
Maintenance:
- Regularly clean the desk using a soft, damp cloth.
- Avoid using abrasive cleaners or solvents that may damage the surface.
- Inspect the power cord for any signs of damage and replace if necessary.
FAQ:
Q: What should I do if the desk is not functioning properly?
A: If you experience any issues with the desk, please contact our technical
support team at (909)637-7665 | (909)637-7593 or email us at HJ-Customer-
Service@outlook.com for assistance.
Q: Can I leave the desk plugged in all the time?
A: Yes, it is safe to leave the desk plugged in when not in use. However,
we recommend unplugging it during prolonged periods of non-use or when
performing maintenance.
Q: What is the warranty period for this product?
A: Please refer to the warranty information provided with your purchase for
details on the warranty period and coverage.
Parts
Installation Instructions
Please read the installation instructions carefully before installation.
-
Align the holes of Left Leg (2) and Drive Rod (4),Using Wrench(M-G)to secure both with Screw (M-A).
-
Insert the drive rod(4) into the hole in the right leg (3). If it is not possible to
insert, please rotate the right leg (3) slightly until the inner hexagon matches. -
As shown, use Wrench (M-H), install Beam (1) to the Legs (2&3) with Screws (M-8)*6.
-
Using Wrench(M-H), install Leg Base (6)2 to the Legs (2&3) respectively with Screws (M-C)8.
-
Use a screwdriver, and install Side Plate (5)2 on each side of the Legs (2&3) with Screws (M-F)4.
-
Use a screwdriver with Screws (M-D) 4 , and Desk Connection Hook (8) 2 to both sides of the Boards.
-
Fix Silicone Sheet (13)*10 to the corresponding hole position on the Board.
-
As shown, connect the motor at the Left Leg (2), Hand Controller (9), and Power Supply (10) in turn.
-
Using a screwdriver install Hand Controller (9) to the Board ( 7 ) with Screws (M-D)2. Secure the connecting cable with Cable Clip (12)2 and glue it to the bottom of the Board
-
Insert Cable Hole Cover (11 )*2 into the hole in the Board ( 7·).
NOTE : Ensure that all bolts are 100% locked
Using the Controller
-
Raise the Desk
Press the ~ button to raise the desk continuously until it reaches the highest position or the button is released. -
Lower the Desk
Press the ~ button to lower the desk continuously until it reaches the lowest position or the button is released -
Select Height Setting 1
Press the GJ button, and the desk will move to the height that was previously set for that button. -
Select Height Setting 2
Press the ~ button, and the desk will move to the height that was previously set for that button. -
Select Height Setting 3
Press the @J button, and the desk will move to the height that was previously set for that button.
Save Current Height Setting
Short-press the S button, and the screen will show ‘S’.Press the [I), ~, or button to save the current height setting to that button. When you press the or button, the desk will move to the height that was previously set for that button. Any button press will stop the desk.
Settings
Reset
Press and hold the~ button until ‘rst’ is displayed. Continue holding until
the desk goes down to its lowest level and comes back up slightly. Release the
button, and the reset is complete. If the button is released during the reset
procedure, the reset will stop. The desk won’t work until the reset is done
correctly.
Child Lock
Press and hold the ~ and ~ buttons together for 5 seconds to turn the child
lock on. The screen will show ‘LOC’ and the buttons will be disabled. Turn
child lock o the same way.
Settings Menu
- Press and hold the [ID button for 5 seconds to enter the settings menu. Short-press the [ID button to navigate through the menu.
- Short-press the ~ or~ button to adjust the settings. Long-press the ~ or ~ button to quickly adjust the height settings. Press and hold the [ID button again to save the changes. ‘SUS’ will be displayed if saving is successful (or ‘FAL’ if saving fails). If there is no button pressed for 10 seconds, the settings menu will be exited automatically.
Power-Saving Mode
The screen will turn o if there is no button press for a minute. Any button
press will turn the screen on again.
Protection Mode Error Codes
sea
|
Standby Overvoltage Protection: Standby voltage too high. Power o the desk, check the connection between power and the controller, and power on again. If the error code persists, please contact technical support.
---|---
SC1
| Power Supply Overvoltage Protection: Input voltage too high If the correct AC adapter is being used, power o the desk, check the connection between power and the controller,
and power on again. If the error code persists, please contact technical support.
SC4
| Operating Overvoltage Protection: The operating voltage too high. Power o the desk, check the connection between power and the controller, and power on again. If error code persists, please contact technical support.
hot
| Overheating Protection: When the motor has been working continuously for too long, it will stop operating to prevent overheating. Wait for at least 18 minutes (until the error code disappears) before making any further height adjustments.
r-6
| Power Supply Overvoltage Protection (during use): Input voltage too high. Error clears when power supply voltage returns to normal. If the error code persists, please contact technical support.
rst
|
Reset Warning: Continue to complete the reset.
E10
|
Short Circuit Protection: Power o, check the cable connections, and power back on again. If error persists, please contact technical support.
Technical Support
Other Info
HJ-Customer-Service@outlook.com
Thank you for choosing this product. We strive to provide you with the best
quality products and service in the industry. Should you have any issues,
please don’t hesitate to contact us.
(909)637-7665 | (909)637-7593
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>