DIOSHOME XXY04 Kid’s Multifunctional Chair Instruction Manual
- June 1, 2024
- DIOSHOME
Table of Contents
Kid’s Multifunctional Chair Instructions
Safety instructions
WARN
Failure to follow the following safety instructions WARN may result in
damage or other injury.
- Instructions for use: In order to avoid accidents for your child when using study desks and chairs, please provide effective guidance for the child before use and prohibit them from playing within the marked warning area. (For example, when adjusting the tilt of the product, pay attention to warning phrases such as “Warning! Be careful of pinching hands”).
- Usage environment: Keep the product away from heat sources during use to avoid furniture aging. Avoid long term exposure to sunlight on the furniture and use curtains to block it.
- Usage regulations: Do not climb or collide with furniture. Do not place items that are too cold or too hot, sharp objects, or rough surfaces directly on the surface of furniture.
- Prohibited items: Children are prohibited from sitting on drawers or desks to play, causing the center of gravity to shift forward, to prevent tipping and personal injury or damage to furniture.
Attention! Only adults are allowed to install, children are not allowed near!
Applicable age range: 3 years old and above.
Installation instructions
Product installation warning
- Please check the completeness of each component according to the parts list before assembly.
- If there is a shortage of parts, please contact the service center and we will be happy to serve you.
- For your convenience in assembly, do not lock all the screws tightly during assembly. After all the parts are locked, tighten them again.
Note: Only adults are allowed to assemble, children should not be approached
Specification parameter
Name: DIOSHOME Kid’s Multifunctional Chair
Model: XXY04
Specification: 20.19X22.44X29.92~36.22IN
Outer box specifications:22.24×16.14×17.32IN
Installation and debugging
- Before installing furniture, please carefully read the attached installation diagram and master the installation steps and methods.
- Check if the accessories are complete and if there are any damages.
- When installing furniture, it is necessary to have a spacious and clean area, with paper sheets laid flat on the ground to avoid collisions between furniture components and the ground during installation.
- It is strictly prohibited to press the plate onto hardware components such as screws and screws during installation, causing damage to the plate.
- Each installation operation must be completed and tightened during installation; Ensure that the product structure is firm.
- After installation, a soft velvet cloth can be used to remove dust and dirt from the surface of the furniture. It is strictly prohibited to use a cloth with gravel to wipe the furniture.
Handling and storage
- When moving furniture, move and handle it gently, and avoid forceful dragging and pushing to avoid loosening or breaking the footrest and tenon structure.
- When transporting, there should be outer packaging and it should be handled with care. When reinstalling, appropriate adjustments should be made to the furniture after placement to maintain its normal use.
- When not in use for a long time, it should be covered with dustproof and strong light resistant packaging materials and stored indoors in a dry and ventilated environment.
Assembly parts list
(1) x1
| (2) x1
| (3) x1
---|---|---
Chair backrest| Chair cushion| Pedal crossbeam
(4) x1
| (5) x1
| (6) x2
Front chair legs left and right| Rear seat legs| Backrest support tube
(7) x2
| (8) x2
| (9) x1
Note: When using this accessory, it is necessary to remove the screws pre- installed in the accessory before installation.
Tee connector
| Back handrail| Pedal
(10) x13
| (11) x5
| (12) x5
Note: This screw has been installed on the three-sided connector.
M6*16 screw
| M4*8 screws| Spring pad
(13) x1
Cross screwdriver
Installation steps
1. Use four M4 * 8mm screws to pass through the spring washer and lock the foot pedal onto the foot pedal iron frame.
2. Loosen the fixing knob and insert the front seat legs into the footrest bracket, with the adjustment holes on the front seat legs facing outward.
Note: The adjustment hole is facing outward
3. As shown in the figure, insert the chair cushion into the front seat legs.
4. Insert two three sided connectors into the front seat legs and lock the three-sided connectors using M6 * 16 screws. facing outward.
- Back support tub
- Rear tripod
- Front foot tube
5. After inserting the legs of the rear seat into the three-sided connector, use M6 * 16 screws to lock the three-sided connector.
6. After inserting the seat back support tube into the three-sided connector, use M6 * 16 countersunk head screws to lock the three-sided connector. The graduated side of the seat back support tube needs to be facing outward. facing outward.
7. After inserting the seat back support tube into the three-sided connector, use M6 * 16 countersunk head screws to lock the three-sided connector. The graduated side of the seat back support tube needs to be facing outward.
8. Insert the two backrest armrests into the backrest support tube to complete the assembly of all chairs. outward.
Function Introduction
A: The seat back is made of high rebound molded cotton material, which
has the characteristics of fast rebound and
B: All supporting metal parts are made of cold-rolled steel, which has
good durability, wear resistance, and support characteristics.
C: The three-sided connectors, sliding brackets, foot pedals, and other
plastic components are all made of PA material, which has the characteristics
of high mechanical strength, high
D: Seat height adjustment: Loosen the left and right knobs by about one
turn and pull the unlocking knob to adjust the seat cushion height. The seat
height range is 12.2-20.86 inches.
E: Foot adjustment: Loosen the left and right knobs by about one turn and
pull the unlocking knob to adjust the seat cushion height, with a sitting
height range of 2.75 to 11.81 inches.
F: The rear casters are made of environmentally friendly PA+PCVL
material, which does not damage the floor and is wear-resistant and anti-skid.
G: Cushion adjustment: Turn on the front and rear switches of the
adjustable cushion to adjust the cushion depth from 0-3.46IN.
H: Back cushion adjustment knob: After the left and right knobs are
simultaneously loosened, the height of the back cushion
I: Full wrap back frame: Made of PP elastic material to wrap the back
cushion, providing you with more comfortable elastic support.
J: The cushion and backrest are made of environmentally friendly PP
material, which has good durability and impact
K: Zipper seat cover: Pull open the zipper for easy disassembly and
cleaning of the seat cover.
(1) Back cushion adjustment knob| (2) Cushion adjustment| (3)
Seat height adjustment
---|---|---
| |
Tighten clockwise and loosen counterclockwise| Press up to adjust seat depth
release and lock| Tighten clockwise and loosen counterclockwise Pull out to
adjust height
Use and maintenance
- Furniture should be kept in a well ventilated environment before use, in order to eliminate residual odors in the surface coating materials of the furniture.
- Educate children not to play close to furniture glass, mirrors, sharp corners, etc. to avoid accidentally damaging their bodies.
- Try to avoid exposure to sunlight on the furniture as a whole or for extended periods of time.
- In summer, if there is indoor dampness, it is advisable to use a thin rubber pad to separate the furniture from the ground, and maintain a distance of 0.5 to 1 cm between the furniture and the wall.
- Do not place items that are too hot or too cold directly on the surface of furniture (such as adding a cushion if used), and do not hit hard objects. Do not hit glass and hardware decorative surfaces.
- In winter, it is best to place furniture about 1 meter away from the heating source to avoid prolonged high temperatures.
- Do not use cleaning agents containing chemicals to clean furniture, and also avoid contact with corrosive liquids such as acids and alkali.
- Heavy items should not be placed on the edge of the countertop, otherwise it will cause the center of gravity of the furniture to be unstable or tilted, leading to damage to the structure and function of the furniture and harm to human health.
- Do not use furniture as a ladder to stand on furniture.
Specification
This manual does not express any position or other implication, it is only used for product service guidance. Therefore, our factory reserves the right to modify the manual, and the content may be updated at any time without prior notice. If you need our latest product information, you can directly log in to the official flagship store of DIOSHOME Amazon to view it.
Remarks
- This warranty card is only applicable to the products and warranty services listed by the company.
- Please refer to Sinbo warranty service for warranty scope.
- Please take good care of this card. This card and related original invoice shall be presented during product warranty
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>