NICOR HBC5SENSORPIR Motion Sensors and Remote Control Instruction Manual

NICOR HBC5SENSORPIR Motion Sensors and Remote Control

Product Information

Product Specifications:

• Voltage Range: 12-24VDC
• Signal: DIM 0-10V
• Stand-by Power: 7.5-16W
• PIR Sensitivity: Adjustable
• Detection Area: Varies based on installation height
• Installation Height: Recommended mounting height of M meters
• Holdtime: Adjustable
• Daylight Threshold: Adjustable
• Standby Dimming Level: Adjustable
• Standby Period: Adjustable
• Dusk/Dawn Sensing/Photocell: Included for automatic light adjustment
• Daylight Harvesting: Enabled for energy efficiency
• Working Temp: Suitable for a range of temperatures
• IP Rating: Weatherproof for outdoor use

Product Usage Instructions

1. Installation:
   Mount the PIR HBC5SENSORPIR at the recommended height of M meters. Ensure proper wiring according to the voltage range specified.

2. Setting Parameters:
   Adjust the PIR sensitivity, detection area, hold time, daylight threshold, standby dimming level, and standby period as per your requirements.

3. Daylight Harvesting:
   Enable the daylight harvesting feature for energy-efficient lighting based on natural light levels.

4. Testing:
   Utilize the test function to ensure proper detection and settings before finalizing the installation.

Frequently Asked Questions (FAQ):

• Q: What is the purpose of the standby dimming feature?
  A: The standby dimming feature allows the light to dim when no motion is detected, conserving energy while providing low-level illumination.

• Q: Can the detection range be adjusted?
  A: Yes, you can adjust the detection range by setting the parameters such as PIR sensitivity and detection area.

• Q: Is the PIR HBC5SENSORPIR suitable for outdoor use?
  A: Yes, the product has an IP rating making it suitable for outdoor environments.

Dimension

INTRODUCTION

• Rotator & Remote control.
• 12VDC Input, 0-10V Dimming, with Daylight Harvesting and Photocell Function.
• Attention: Please set the parameters in the state that the light is always on, the light brightness will blink when the sensor receives the signal, and it will not receive the signal of “MH”, “CCT”, or”o” on the remote control.
• Set the fixture on the highest wattage.

PARAMETERS

switch：5s/1min/5min/10min
Daylight Threshold| Remote Control：2Lux/10Lux/30Lux/50Lux/80Lux/120Lux/200Lux/250Lux/ 300Lux/350Lux/400Lux/Disable
Standby Dimming Level| Remote Control：10%/20%/30%/50% Rotating switch：0%/10%/20%/30%
Standby Period| Remote Control：0s/10s/30s/1min/5min/10min/30min/60min/+∞
Dusk/Dawn Sensing/ Photocell| Daylight threshold as 30lux/50lux/80lux/120lux/200Lux/ 250Lux/300Lux/350Lux/400Lux

Standby period as +∞;

Standby dimming level as 10%/20%/30%

Daylight Harvesting

| 1. Choose the “Daylight sensor” button then adjust to any value higher than 50LUX

2. Choose “Standby Period” then adjust to 0S

3. Press the “DH” daylight harvesting button, till the LCD screen show DH-ON

4. Remark: this function cannot be turned off by DH-OFF. but it can be turned off by changing any parameters

Environmental Requirements| In accordance with CE ROHS
Working Temp| -30°C~+70°C
IP Rating| IP65

WARNING

• NOTE: Warm-up time is 45 seconds. After the sensor connects input power the first time, the light will keep on for 45 seconds, then go to dimming to work normally.
• NOTE: Factory Default Setting: 100% sensitivity, Hold on time: 1 min, Daylight threshold is disabled, Standby period is I min, standby dimming Level is 20%.

DAYLIGHT HARVESTING

1. Choose the “Daylight sensor” button then adjust to any value higher than 50LUX
2. Choose “Standby Period” then adjust to 0S
3. Press the “DH” daylight harvesting button, till the LCD screen show DH-ON
4. Remark: this function cannot be turned off by DH-OFF, but it can be turned off by changing any parameters

• When ambient brightness is lower than the preset lux level, the sensor will turn on the light automatically and keep dimming according to the change of the ambient brightness; when the outside is getting darker, the inside will be brighter, and brighter.
• Light OFF when ambient brightness becomes higher than the preset lux level.

DUSK/DAWN FUNCTION

HBC5SENSORPIR can differentiate artificial light brightness from natural light after being installed inside the fixture, and automatically turn off the light when ambient brightness exceeds the preset lux level.

Precondition of Dusk/Dawn function:

1. Standby period is +∞;
2. Standby dimming level is at 10%,20%, or 30%;
3. Daylight threshold is on 30lux/50lux/80lux/120lux/200Lux/250Lux/300Lux/350Lux/400Lux

DETECTION COVERAGE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>