JANNATEC Technologies CC1020 Module User Guide
- June 3, 2024
- JANNATEC Technologies
Table of Contents
JANNATEC Technologies CC1020 Module
Revision History
| REV | DESCRIPTION | ORIGINATOR | DATE |
|---|---|---|---|
| 1.0 | Initial Release | J. Buie | October 6, 2022 |
Release Approval
| NAME| SIGNATURE
---|---|---
Prepared by
| ****
Jason Buie
|
Approved by
| |
Approved by
| |
Background
This guide has been developed to aid in the integration of the CC1020 module
from mechanical, RF and electrical perspectives.
Interface Diagram
Connectivity
Power, Programming, Host UART and GPIO
Connections for power, programming, host UART and GPIOs are made through 4 low
profile connectors populated on the bottom of the CC1020 module. The mating
connectors required are Molex DF40B-12DS-0.4V(58).
Pinout – J2
| PIN | SIGNAL |
|---|---|
| 1 | VIN |
| 2 | MCLR_IN |
| 3 | VCC |
| 4 | RA0 |
| 5 | VCC |
| 6 | RA1 |
| 7 | GND |
| 8 | PGD |
| 9 | GND |
| 10 | PGC |
| 11 | GND |
| 12 | 3.0V_Micro |
Pinout – J3
| PIN | SIGNAL |
|---|---|
| 1 | RB3 |
| 2 | UART_RX |
| 3 | RA2 |
| 4 | UART_CTS |
| --- | --- |
| 5 | RA3 |
| 6 | UART_TX |
| 7 | RA4 |
| 8 | UART_RTS |
| 9 | RB5 |
| 10 | RB2 |
| 11 | N/C |
| 12 | N/C |
Pinout – J4
| PIN | **SIGNAL *** |
|---|---|
| 1 | J4 COMMON |
| 2 | J4 COMMON |
| 3 | J4 COMMON |
| 4 | J4 COMMON |
| 5 | J4 COMMON |
| 6 | J4 COMMON |
| 7 | J4 COMMON |
| 8 | J4 COMMON |
| 9 | J4 COMMON |
| 10 | J4 COMMON |
| 11 | J4 COMMON |
| 12 | J4 COMMON |
No signals on J4 pins. Connect together for mechanical support.
Pinout – J5
| PIN | **SIGNAL *** |
|---|---|
| 1 | J5 COMMON |
| 2 | J5 COMMON |
| 3 | J5 COMMON |
| 4 | J5 COMMON |
| 5 | J5 COMMON |
| 6 | J5 COMMON |
| 7 | J5 COMMON |
| 8 | J5 COMMON |
| 9 | J5 COMMON |
| 10 | J5 COMMON |
| 11 | J5 COMMON |
| 12 | J5 COMMON |
No signals on J5 pins. Connect together for mechanical support
RF Connection
RF connection to the CC1020 module is done through an onboard U.FL connector.
This module must only be used with a 1” U.FL coaxial jumper to the host board
and an approved antenna.
Antenna Requirements
The CC1020 module has been given modular IC and FCC certifications with two antenna configurations. Use of antenna configurations other than is described below must not be used.
Ceramic Antenna on Host Board
A 1” U.FL coaxial jumper is used to make the RF connection between the CC1020
module and the host board. The host board is populated with a Pulse W3014
(-0.5dBi) ceramic antenna or equivalent.
Low Profile Mobile Antenna
A 1” U.FL coaxial jumper is used to make the RF connection between the CC1020
module and the host board. A minimum of 17’ of RG58 makes the connection
between the host board and an NMO magnetic mount with a PCTEL MLPV800 (3dBi)
or equivalent.
Specifications
- Input Voltage: 3.5-16Vdc
- Input Current: 25mA max
- Max EIRP with certified antenna configurations: -1.5dBm
- Length: 30mm (1.18”)
- Width: 21.6mm (0.85”)
- Height: 4.95mm (0.185”)
RF Certification
Host Product Labelling:
The host product must be labeled with the following:
- “Contains FCC ID: 2AZ9PCC1020”
- “Contains IC: 7085A-CC1020”
Host Product Manual Statements:
The host product user’s manual must contain the following statements when the
JAWS transceiver Module is installed.
FCC –
“Changes or modifications not expressly approved by Jannatec Technologies
could void the user’s authority to operate the device.” “This device complies
with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.” “To comply with RF exposure compliance
requirements, the antenna used for this transmitter must be installed to
provide a separation distance of at least 20cm from all persons and must not
be co-located or operated in conjunction with any other antenna or
transmitter.
Caution: Exposure to Radio Frequency Radiation.
To comply with RSS 102 RF exposure compliance requirements, for mobile
configurations, a separation distance of at least 20 cm must be maintained
between the antenna of this device and all persons. This device must not be
co-located or operating in conjunction with any other antenna or transmitter.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>