Esistyle srl N01US-4speeds Remote Control Instruction Manual
- June 1, 2024
- Esistyle srl
Table of Contents
Esistyle srl N01US-4speeds Remote Control
Specifications
- Remote Control Model: N01US-4speeds
- Range: Approximately 10-15 feet
- Features: Magnetic base, plastic top material, sleep mode after 4 seconds of inactivity
Product Usage Instructions
Synchronization
- Ensure the range hood is off.
- Press and hold the second speed button on the range hood for 5 seconds to enter learning mode.
- Simultaneously press the P1 and PT buttons on the remote control for 3 seconds.
- If successful, the light symbol on the hood control will stop flashing and the range hood is synchronized.
- If issues persist, repeat the procedure.
General Information
- The remote control has a range of 10-15 feet.
- The remote control features a magnetic base for easy attachment to ferrous surfaces.
- Handle the remote with care as the top is prone to scratches; use a soft cloth for cleaning.
- The remote enters sleep mode after 4 seconds of inactivity to conserve battery life; press any button to wake it up.
Functions
- P0: Power button – displays ‘0’ when pressed with the motor off.
- P1: Decrease motor speed; switches off when the hood is in 1st speed.
- P2: Increase motor speed; different presses for different speeds (1-4).
- PL: Lights On/Off and intensity adjustment; press and hold to adjust light intensity.
- PT: Timer function; press shortly to enable a 15-minute countdown that stops the blower at the end.
RF Exposure Statement
This equipment complies with FCC radiation exposure limits for an uncontrolled environment. Avoid co-location with other transmitters.
FCC Warning
FCC ID: 2BDWI-N01US. This device complies with FCC Rules and should not cause harmful interference. Follow guidelines for proper operation.
FAQ:
Q: How can I adjust the light intensity using the remote control?
- A: Press and hold the PL button to start adjusting the light intensity. Release the button once the desired level is reached. Repeat to readjust if needed.
Q: What should I do if my remote control does not synchronize with the range hood?
- A: Repeat the synchronization process, ensuring both devices are in the correct mode and within range of each other. If issues persist, contact customer support for assistance.
SYNCHRONIZATION
To synchronize the remote control with the range hood for the first time, proceed as follows:
- With the range hood off, press and hold for 5 seconds the second speed button, the range hood should enter learning mode, and the light symbol on the hood control button will flash for 60 seconds.
- Press the “P1” and “PT” buttons simultaneously on the remote control for 3 seconds, and “L” will appear on the display “PD”.
- If synchronization is successful, the light symbol on the hood control will stop flashing turn on for 3 seconds, and then turn off.
The range hood is now synchronized with the remote control. If you experience any problems, repeat the procedure.
GENERAL INFORMATION
- The remote control has a range of approximately 10-15 feet.
- The remote control is equipped with a magnetic base and may be attached to a ferrous surface for easy storage.
- The remote top is made of a plastic material and is prone to scratches. Use care when handling and cleaning the remote; we suggest using a soft cloth to clean it.
- The remote control will enter sleep mode after 4 seconds of inactivity to preserve battery life. Press any button to wake the remote.
FUNCTIONS
- P0:Power button -when pressed with the motor off, the display shows “0” (zero) for about 1 second.
- P1:Motor speed decrease button; when the hood is in 1st speed, P1 switches the motor off.
- P2:Motor speed increase button; when the hood is off, touch once for first speed, twice for 2nd speed, three times for 3rd speed, and four times for 4th speed. The display shows the selected speeds(“1”, “2”, “3”, “4”).
PL: LIGHTS ON/OFF and LIGHTS functions selection
- Light intensity – light level intensity can be adjusted. With lights on, press and hold the “PL” button: the light intensity starts decreasing or increasing until it reaches the minimum or maximum value (depending on the last intensity saved). Once the desired light intensity is reached, release the button to stop the process; pressing and holding the “PL” key again will restart the adjustment procedure.
- Light Color – light color can be adjusted. With lights off, press and hold the “PL” button until the light symbol on the hood control starts blinking. Start touching the “PL” button briefly to set up the light’s color. There are 10 (ten) different light colors from a minimum of 2700K to a maximum of 6000K.
Once the desired color has been selected, to memorize it, wait 10 seconds until the light symbol on the hood control stops blinking, and the dynamic selection mode ends.
PC: CLEAN AIR function (disabled by default)
- To enable the Clean Air function, with the hood off, press the “PC” button to enter the Clean Air function menu. Press and hold the “PC” button for 4 to 5 seconds, The Clean Air function is now active (a “C” will appear on the display), and the blower will turn on at the first speed and work for 10 minutes. After 10 minutes the fan will turn off, and the 50-minute timer will start, with the hood control light symbol flashing every 5 seconds. After 50 minutes the fan will start again for 10 minutes. After 24 hours of cycling, the Clean Air function will be disabled automatically. To disable the function while it is enabled, press either PC or P0 button.
PC: QUICK AIR REFRESH function:
- To enable the Quick Air Refresh function, with the hood on or off, press the “PC” button to enter the Quick Air Refresh function menu. Press the “PC” button again, the Quick Air Refresh function will now be active (a “C” will appear on the display), and the blower will turn on at the maximum speed and work for 6 minutes, allowing a rapid air renewal. At the end of the 6 minutes, the blower will switch off automatically.
- While the function is active, the hood control light symbol flashes everysecond. To disable this function, press either “PC” or “P0” button.
Note: this function has priority over all the other active motor functions.
PT: TIMER function(disabled by default)
- To enabletimer press shortly “PT”. The Timer performs a 15-minute countdown and can only be activated with the fan is on, “T” appears on the display.
- The duration of 15 minutes does not change even if the speeds are changed during the countdown.
- At the end of the 15 minutes the blower stops.
- PD: Display
RF exposure statement
This equipment complies with the FCC radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Warning
FCC ID: 2BDWI-N01US
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference
- This device must accept any interference received, including interference that may cause undesired operation
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used under the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE : Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.