FEIT ELECTRIC UCL24 24 Inch Smart Wi-Fi Under Cabinet Light Instruction Manual

FEIT ELECTRIC UCL24 24 Inch Smart Wi-Fi Under Cabinet Light Instruction Manual

Safety Information

IMPORTANT: ALWAYS FOLLOW BASIC SAFETY PRECAUTIONS WHEN USING ELECTRICAL PRODUCTS, ESPECIALLY WHEN CHILDREN ARE PRESENT.

CAUTION: Do not attempt to install while plugged in. This fixture is for indoor use only. Not for use with plastic cabinets. Do not install this fixture inside a totally enclosed cabinet. Do not mount over stoves.
WARNING: To avoid risk of electrical shock, always make sure the product is unplugged from the electrical outlet before assembling, disassembling, relocating, servicing or cleaning it.
CAUTION: Do not install this product in a wet location.
CAUTION: Do not install this product in an outdoor location.
CAUTION: Do not use chemical solvents or harsh abrasives to clean the fixture.

Responsible Party: Feit Electric Company 4901 Gregg Road, Pico Rivera, CA 90660, USA 562-463-2852 Unique Identifier: UCL24/CCICA/AG

FCC STATEMENT

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment www.feit.com. CAN ICES-005(B).

Limited Warranty

This product is warranted to be free from defects in workmanship and materials for up to 1 year from date of purchase. If the product fails within the warranty period, please contact Feit Electric at info@feit.com, visit feit.com /contact-us or call 1-866 326-BULB (2852) for instructions on replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY.LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

Pre-Assembly

TOOLS REQUIRED

HARDWARE INCLUDED

NOTE: Hardware not shown to actual size.

Plug-in Installation

Positioning the Fixture

Find the desired place for the LED fixture and mark clearly using the fixture mounting template (FF).

Installing the Mounting Brackets

Drill holes at the marked locations. Secure the mounting brackets (EE) by screwing the mounting screws (DD) into the drilled holes.

Installing the LED Fixture

Align and snap the LED fixture (AA) onto mounting brackets (EE). r—

NOTE: You can slide the LED fixture (AA) left or right to adjust position.

Connecting the Electrical Plug

Plug in the electrical plug (BB) into the LED fixture (AA).

WARNING: Do not plug the electrical plug (BB) into a wall power source until after connecting to the LED fixture (AA).

Connecting to a Power Outlet

Connect the electrical plug (BB) to the power outlet on the wall.

Linking LED Fixtures

Connect the LED fixtures (AA) using the provided linking cable (BB). single fixture installation instructions with two or

NOTE: To install two or more LED fixtures, repeat the more units.

Hardwire Installation

Turning Off the Power

Turn the power OFF at the switch, fusebox or the circuit breaker.

Removing the Back Panel

Use a screwdriver to pry open the back panel of the LED fixture (AA).

Removing the Knockout

Carefully remove a knock-out with a flathead screwdriver.

Installing the Clamp Connector to the Knockout Hole

Install the cable clamp connector (Il) to the knockout hole by inserting it through the hole and securing it with the nut. The cable clamp connector (HH) should be on the outer side  of the bracket.

Cutting and Stripping Wires

Unfasten the black and white 18 AWG wires from the back of the fixture. Cut and strip the wires to the correct length.

Wiring Power Supply to the Fixture

Feed the supply wires through the cable clamp connector (HH) and knockout hole and make all connections using the wire nuts (LL). Select a pair of black and white wires that are conventiently located. Connect the 120V live (black) wire to a black wire. Connect the neutral (white) wire to a white wire. Remove the protective sheath before connecting the wires.

Securing the Supply Wires with the Cable Clamp Connector

Secure the supply wire by firmly screwing the cable clamp connector (HH) down on the wire.

Replacing the Back Panel

Snap the the back panel of the LED fixture (AA) into place.

Positioning the Fixture

Find the desired place for the LED light fixture and mark clearly using the provided fixture mounting template (FF).

Installing the Mounting Brackets

Drill holes at the marked locations. Secure the mounting brackets (EE) by screwing the mounting screws (DD) into the drilled holes.

Installing the LED Fixture

Align and snap the LED fixture (AA) onto mounting brackets (EE).

NOTE: You can slide the LED fixture (AA) left or right to adjust position.

Linking LED Fixtures

Connect the LED fixtures (AA) using the provided  linking cable (BB).

NOTE: To install two or more LED fixtures, repeat the single fixture installation instructions with two or more units.

Operating Instructions

Changing the Brightness Levels

To select the desired brightness level, cycle through brightness levels (High, Medium, Low, Dim, Off) by pressing the dim button. This setting will be fixed each time the ON/OFF switch is turned ON.

Changing the Color Temperature Setting

To select the desired color temperature, cycle through 2700K – 3000K – 3500K – 4000K – 5000K – 6500K by pressing the CCT button.  This setting will be fixed each time the ON/OFF switch is turned ON.

Entering Pairing Mode

To enter pairing mode, press both CCT button and On/Off Button on the fixture until the unit flashes

Remote Control Operation

NOTE: To set favorite settings: Set the light to the  desired brightness level and color temperature. Press and hold the preset number you want to save to. The unit will flash once saved.

App Setup

Download the Feit Electric app on your smart device

NOTE: Be sure to connect to a 2.4 GHz Wi-Fi network that covers your installation location.

Pairing instructions

To go into pairing mode, press both dim button and CCT button on the fixture. The unit will start blinking.

Connect Using Bluetooth

Turn on Bluetooth and open the Feit Electric app to complete the set up

Tap Add Device or the + sign. The device name(s) will pop up on the Feit app. Tap on Go to add, then select the device to add. You will be prompted to enter your Wi-Fi network name and password.

Only one device may be added at a time using Bluetooth set up. Repeat Step 3 to add additional devices. Alternative set up options and help instructions are available in the Feit Electric app.

WARNING: These products may represent a possible shock or fire hazard if _ improperly installed or attached in any way. Products should be installed in accordance with this install guide, current electrical codes and/or the current National Electric Code (NEC).

NOTE: Indicator light must _ be rapidly blinking to connect. If not already blinking, press and hold the power button for five seconds.

Connect Using WiFi

Launch and use the Feit Electric app to complete the set up

Tap Add Device or the + sign, then select a Smart Wi-Fi product and confirm. You will be prompted to enter your Wi-Fi network and password.

Troubleshooting Tips Wi-Fi

If you are having difficulty connecting: pcs ,

• Make Sure the Wifi network la # 2.4 GHz network. ©
• The Wi-Fi connection may not have good coverage during set up.
  • Try moving the Smart product closer to your Wi-Fi router.
•  Your Wi-Fi network password is case sensitive, make sure youare entering correctly.
• Smart product will not connect to a 5 GHz network.
• Test your Wi-Fi network with other devices such as your phone to make sure it is operating properly.

Check the App User Guide for more information.

Need Help?

Thank you for your purchase. Questions, comments or feedback? We’d love to hear from you. Visit feit.com/help for support or connect with us:

@FeitElectric |
@FeitElectricInc
@ feitelectriclighting

QR code

Documents / Resources

| FEIT ELECTRIC UCL24 24 Inch Smart Wi-Fi Under Cabinet Light [pdf] Instruction Manual
UCL24, CCTCA, UCL24 24 Inch Smart Wi-Fi Under Cabinet Light, UCL24, 24 Inch Smart Wi-Fi Under Cabinet Light, Smart Wi-Fi Under Cabinet Light, Under Cabinet Light, Cabinet Light, Light
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>