FoxAlien HFS-800 Vacuum Cleaner Hepa Filter System User Manual

FoxAlien HFS-800 Vacuum Cleaner Hepa Filter System

Product Specifications

Air Hose Diameter

|

Inner diameter: 27.8mm (1.0”); Outside diameter: 32mm (1.26”)

Air Outlet Diameter| Inner diameter: 32.3mm (1.27”); Outside diameter: 36mm (1.42”)
Machine Size| 430 x 235 x 298mm (17” x 9.25” x 11.73”)

Product Introduction

Adjustable Airflow: 0 ~ 800W (max.)
NOTE: Continuous long-hour working in maximum power may affect the product service life.

How To Use

1. Connect the air hose to one of the ports.
2. Connect power, and power on the machine.
3. Turn the knob to increase the airflow volume.
   NOTE: Do not connect the air hose to the air outlet and air intake at the same time!

Maintenance

To maintain the machine in good condition and improve the service life, regular maintenance is highly recommended. Disconnect power before maintenance.

Cleaning the dust collector
Disconnect the power before cleaning. Use a soft cloth to clean the machine’s surface. Do not clean with chemical solvents such as alcohol, gasoline, and benzene.

Check and replace the filters regularly

• Always empty the dust bags regularly. Emptying the dust bag allows the machine to operate at a much higher level of efficiency.
• Replacement of the filters regularly. It depends on how much dust it collects.
• You can visibly see if the filter needs to be changed, it goes from white to dingy grey.
• Please contact FoxAlien Official for filter filaments purchasing.
  NOTE: Always wear a respirator when emptying the dust bag. Sawdust may cause allergic reactions or respiratory problems.

How to replace the filters

• As Image A, open the bin, and take out the filters and dust bag.
• As in Image B, remove the PE bags of the new filters.
• As in Image C, install the new filters and dust bags into the bin, and close the door.

NOTE
PE bags must be removed before installation; otherwise, the machine cannot work correctly.

DOs & DON’Ts

• Make sure the power source matches wire voltage configurations.
• Always place the machine on a stable surface to avoid falling caused by the vibration during operation.
• Use to machine in a good ventilation environment.
• Keep both the interior and exterior of the machine free from dirt, water, oil and grease.
• If an extension cord is necessary, a cord with adequate-size conductors that are capable of carrying the current necessary for your tool must be used.
• When the dust collector is not in use, unplug the power cord from the power source. Place the cord away from potential damage sources such as sharp objects, heat sources, harsh chemicals, water, damp areas, etc.
• Place the cord away from potential damage sources such as sharp objects, heat sources, harsh chemicals, water, damp areas, etc.
• Power OFF the machine and unplug the power cord before moving, checking, and maintenance to avoid electric shot and damage.
• Do not put any hard objects in the machine to avoid any damage to the machine.
• Do not use the machine if the power cord or power socket is damaged or loose. Contact us for prompt assistance.
• Do not use the machine with wet/moisture material.

WARNING

• Do not disassemble the machine without authorization in case of any electric shock.
• And this will void the warranty.
• Disconnect the power and unplug the power cord before changing the filters.
• Review the following troubleshooting tips first when a problem occurs.
• If the problems are not covered, please contact us: at aftersale@foxalien.com.

Troubleshooting Tips

OFF or is at fault.

2.     Wall fuse/circuit breaker is blown/tripped.

3.     Wiring is open/has high resistance.

4. The motor is faulty.

| 1.     Ensure the power supply is switched on; ensure the power supply has the correct voltage.

2.     Ensure circuit size is suitable for this machine; replace the fuse/breaker.

3.     Check for broken wires or disconnected/corroded connections, and repair/replace them as necessary.

4.     Contact us to test/repair/replace.

The machine has a vibration or noisy operation.| 1. The motor, motor mount or other mounting component is loose or broken.

2. The machine is incorrectly mounted or sits unevenly.

3. The impeller is loose or damaged and unbalanced.

4.     Motor bearings are at fault.

| Disconnect the dust collector from the power, and contact us for prompt assistance to test/repair/replace it.
Repetitious noise or dull sound coming from the dust collector.| 1. Plastic bags of the filters are not removed.

2.     Dust ports are blocked.

| 1.     Ensure the plastic bags of the filter are removed, especially for the new filters.

2.     Check and clean the dust ports.

Dust collector does not adequately collect dust or chips; poor performance.| 1. The dust collection bag is full.

2.     Filter is dirty.

3.     Restriction in duct line.

4. The dust collector is too far away, or there are too many sharp bends in the ducting.

5.     Lumber is wet and dust not flowing through ducting smoothly.

6.     Leaks in ducting or too many open ports.

7.     Ducting or machine dust ports are incorrectly sized.

| 1.     Empty collection bag.

2.     Clean or replace filters.

3.     Remove restriction in the duct line.

4.     Relocate the dust collector closer to the point of suction, and rework ducting without sharp bends.

5.     Do not process with wet material.

6.     Rework the ducting to eliminate all leaks.

7.     Re-install correctly sized ducts and fittings

NOTE
Since the machine is fresh from the factory, a slight odour is normal during initial use.

Warranty & Returns

FoxAlien Official warrants this dust collector machine it sells for 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs alterations or lack of maintenance. To take advantage of this warranty, contact us by E-mail and give us all the details. The manufacturers reserve the right to change specifications at any time because they constantly strive to achieve better quality equipment. We make every effort to ensure that our products meet high quality and durability standards and we hope you never need to use this warranty.

Please feel free to contact us if you have any questions about the machine or the manual.
E-mail address: aftersale@foxalien.com / support@foxalien.com The message will be replied to within 2 business days.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>