AC Pro RG10L2 Air Conditioner Owner’s Manual

AC Pro RG10L2 Air Conditioner

Product Information

This remote controller is designed for use with our air conditioning units. It provides convenient control over various functions to ensure optimal comfort and energy efficiency.

Specifications

• Model: RG10L2(D2HS)/BGEFU1

Handling the Remote Controller
To insert or replace batteries:

1. Slide the back cover downward to access the battery compartment.
2. Insert the batteries, ensuring the correct polarity.
3. Slide the battery cover back into place.

Battery Notes:

• If not using the device for more than 2 months, remove the batteries.
• Dispose of used batteries according to local laws.

Buttons and Functions

• ON/OFF: Turns the unit on or off.
• SET: Scrolls through operation functions.
• TEMP: Adjusts temperature.
• FAN SPEED: Selects fan speed levels.
• SWING: Controls louver movement.
• MODE: Selects operation mode (AUTO, COOL, DRY, HEAT, FAN).
• SLEEP: Energy-saving mode for sleeping hours.
• OK: Confirms selected functions.
• TIMER: Sets timer for unit operation.
• ECO/GEAR: Adjusts energy-saving settings.
• HUMIDITY: Controls room humidity during Dry operation.

FAQ

• Q: How do I change the fan speed?
  To change the fan speed, press the FAN SPEED button on the remote control and use the TEMP buttons to adjust the speed level in increments. The available speed levels are AU 20%, 40%, 60%, 80%, and 100%.

• Q: What is the purpose of the SLEEP mode?
  The SLEEP mode helps save energy during sleeping hours by adjusting the temperature settings for comfort while reducing energy consumption.

Remote Controller Specifications

Quick Start Guide

NOT SURE WHAT A FUNCTION DOES?
Refer to the How to Use Basic Functions and How to Use Advanced Functions sections of this manual for a detailed description of how to use your air conditioner.

SPECIAL NOTE

• Button designs on your unit may differ slightly from the example shown.
• If the indoor unit does not have a particular function, pressing that function’s button on the remote control will have no effect.
• When there are wide differences between “Remote controller Manual” and “USER’S MANUAL” on function description, the description of “USER’S MANUAL” shall prevail.

Handling the Remote Controller

Inserting and Replacing Batteries
Your air conditioning unit may come with two batteries(some units). Put the batteries in the remote control before use.

1. Slide the back cover from the remote control downward, exposing the battery compartment.
2. Insert the batteries, paying attention to match up the (+) and (-) ends of the batteries with the symbols inside the battery compartment.
3. Slide the battery cover back into place.

BATTERY NOTES
For optimum product performance:

• Do not mix old and new batteries, or batteries of different types.
• Do not leave batteries in the remote control if you don’t plan on using the device for more than 2 months.

BATTERY DISPOSAL
Do not dispose of batteries as unsorted municipal waste. Refer to local laws for proper disposal of batteries.

TIPS FOR USING REMOTE CONTROL

• The remote control must be used within 8 meters of the unit.
• The unit will beep when remote signal is received.
• Curtains, other materials and direct sunlight can interfere with the infrared signal receiver.
• Remove batteries if the remote will not be used more than 2 months.

NOTES FOR USING REMOTE CONTROL
The device could comply with the local national regulations.

• In Canada, it should comply with CAN ICES-3(B)/NMB-3(B).
• In USA, this device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
  1. This device may not cause harmful interference, and
  2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• Changes or modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.

Buttons and Functions

Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control. The following is a brief introduction to the remote control itself. For instructions on how to operate your air conditioner, refer to the How to Use Basic Functions section of this manual.

Remote Screen Indicators
Information are displayed when the remote controller is power up.

Note:
All indicators shown in the figure are for the purpose of clear presentation. But during the actual operation, only the relative function signs are shown on the display window.

How to Use Basic Functions

ATTENTION Before operation, please ensure the unit is plugged in and power is available.

AUTO Mode

NOTE:

1. In AUTO mode, the unit will automatically select the COOL, FAN, or HEAT function based on the set temperature.
2. In AUTO mode, fan speed can not be set.

COOL or HEAT Mode

DRY Mode
NOTE: In DRY mode, fan speed can not be set since it has already been automatically controlled.

FAN Mode

NOTE: In FAN mode, you can’t set the temperature. As a result , no temperature displays in remote screen.

Setting the TIMER
TIMER ON/OFF – Set the amount of time after which the unit will automatically turn on/off.

TIMER ON setting

TIMER OFF setting

NOTE:

1. When setting the TIMER ON or TIMER OFF, the time will increase by 30 minutes increments with each press, up to 10 hours. After 10 hours and up to 24, it will increase in 1 hour increments. (For example, press 5 times to get 2.5h, and press 10 times to get 5h,) The timer will revert to 0.0 after 24.
2. Cancel either function by setting its timer to 0.0h.

TIMER ON & OFF setting(example)
Keep in mind that the time periods you set for both functions refer to hours after the current time.

Example: If current timer is 1:00PM, to set the timer as above steps, the unit will turn on 2.5h later (3:30PM) and turn off at 6:00PM.1

How to Use Advanced Functions

Swing function

Airflow direction

LED DISPLAY

Silence function

ECO/GEAR function

• ECO operation:
  Under cooling mode, press this button, the remote controller will adjust the temperature automatically to 24 C/75 F, fan speed of Auto to save energy (only when the set temperature is less than 24 C/75 F). If the set temperature is above 24 C/75 F, press the ECO button, the fan speed will change to Auto, the set temperature will remain unchanged.
  NOTE:
  Pressing the ECO button, or modifying the mode or adjusting the set temperature to less than 24 C/75 F will stop ECO operation. Under ECO operation, the set tmeperature should be 24 C/75 F or above, it may result in insufficient cooling. If you feel uncomfortable, just press the ECO button again to stop it.

• GEAR operation:
  Press the ECO/GEAR button to enter the GEAR operation as following:

  • 75%(up to 75% electrial energy consumption)
  • 50%(up to 50% electrial energy consumption)
  • Previous setting mode.

Under GEAR operation, the display on the remote controller will alternate between electical energy consumption and set temperature.

Turbo Function

Sleep Function

FP function
Press this button 2 times during one second under HEAT Mode and setting temperature of 16 C to activate FP function. Press On/Off, Sleep, Mode, Fan and Temp. button while operating will cancel this function.

Note: This function is for heat pump air conditioner only.

LOCK function

Lifting panel function

SET function

• Press the SET button to enter the function setting, then press SET button or TEMP or TEMP button to select the desired function. The selected symbol will flash on the display area, press the OK button to confirm.

• To cancel the selected function, just perform the same procedures as above.
  Press the SET button to scroll through operation functions as follows: Breeze away ( ) Active clean/Self clean ( ) Fresh ( ) Follow Me( ) AP mode ( ) Breeze away….
  *[]:** Model dependent

• Breeze Away function( ) (some units):

  • This feature avoids direct air flow blowing on the body and makes you feel indulging in silky coolness.
    NOTE: This feature is available under cool, Fan and Dry mode only.
    

  • Active clean function( ) (some units):
    The Active Clean Technology washes away dust, mold, and grease that may cause odors when it adheres to the heat exchanger by automatically freezing and then rapidly thawing the frost. When this function is turned on, the indoor unit display window appears “CL”, after 20 to 45 minutes, the unit will turn off automatically and cancel CLEAN function.

  • FRESH function( ) (some units) :
    When the FRESH function is initiated, the Ionizer/Plasma Dust Collector(depending on models) is energized and will help to remove pollen and impurities from the air

  • Follow me function( ) :
    The FOLLOW ME function enables the remote control to measure the temperature at its current location and send this signal to the air conditioner every 3 minutes interval. When using AUTO, COOL or HEAT modes, measuring ambient temperature from the remote control(instead of from the indoor unit itself) will enable the air conditioner to optimize the temperature around you and ensure maximum comfort.
    NOTE: Press and hold Turbo button for seven seconds to start/stop memory feature of Follow Me function.

  • If the memory feature is activated, ,,On displays for 3 seconds on the screen. If the memory feature is stopped, ,,OF displays for 3 seconds on the screen.

  • While the memory feature is activated, press the ON/OFF button, shift the mode or power failure will not cancel the Follow me function.

  • AP function( ) (some units):
    Choose AP mode to do wireless network configuration. For some units, it doesn’t work by pressing the SET button. To enter the AP mode, continuously press the LED button seven times in 10 seconds.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>