User ManuAC Pro edge AC-EX70-UHD-KIT Ultra Slim 70 Meter HDMIal

AC Pro edge AC-EX70-UHD-KIT Ultra Slim 70 Meter HDMI

Introduction

The AVPro Edge primary extender is the most cost effective, state of the art, and reliable single CAT 70 meter extender on the market today. It solves problems for both commercial and residential markets for distributing high value 4K UHD content from rack to display. With the additional ability to cascade extenders, affordable and reliable HDMI extension is now possible. Additionally AC-EX70-UHD-KIT offers solutions for UHD/HD uncompressed distribution in residential digital entertainment centers, retail stores, AV events that require reliable and long distance distribution, suitable for Data Center, Control Rooms, Conference Rooms, Schools and Corporate Training environment.

Features

• HDMI 2.0
• EDID Management
• 4K60 4:2:0, 4K30 4:4:4
• HDR Support up to 4:2:2 12 Bit
• Ultra Slim (.47 inch/12mm)
• Supports 3D
• HDCP 2.3 & Earlier
• CEC Pass Through
• 70M (230ft) on 1080P (Cat6a)
• Up to 40m (131ft) on 4K (Cat6a)
• 48v PoH (Power Over HDBaseT at either end-, only one Power Supply Needed)
• I-Pass Feature for control system “pass-through”
• 3-20v protection circuit built in for safe IR transport
• Bi Directional RS232 Transport
• LED Status, Link, Power indication lights
• Use single UTP/STP LAN cable (CAT-5E/6A) with substitute HDMI cable to achieve long distance transmission.
• Supports uncompressed PCM 2- Ch., LPCM 5.1 & 7.1, Dolby Digital, DTS, Dolby TrueHD, DTS HD-Master Audio, Atmos on HDMI
• ESD protection circuitry (Inputs & Outputs) to 7KV
• Can Cascade

In The Box

• AC-EX70-UHD-T2 (Transmitter)
• AC-EX70-UHD-R2 (Receiver)
• 48V Power Supply (One supplied as Rx is powered by Tx or vice versa)
• 1 x IR Tx Unit
• 1 x IR Rx Unit
• 3.5mm stereo plug to male DB9 for RS-232 to serial port
• 3.5mm stereo plug to female DB9 for RS-232 to PC
• Mounting Brackets

Specifications

VIDEO:

VIDEO RESOLUTIONS| UP TO 4K 60HZ 4:2:0 & 4K30 4:4:4
VESA RESOLUTIONS| UP TO 2560X2048 COSXGA)
HOR FORMATS/RESOLUTIONS| 4K24 4:2:2 12 BIT, 4K24 4:2:0 10 BIT
COLOR SPACE| YUV CCOMPONENTJ, RGB
CCSC: REC. 601, REC. 709, BT2020, DCI, P3 D6500)
CHROMA SUBSAMPLING| 4:4:4, 4:2:2, 4:2:0 SUPPORTED
DEEP COLOR| UP TO 16 BIT (1080) UP TO 12 BIT (4K)
AUDIO:
AUDIO FORMATS SUPPORTED HDMI| PCM 2.0 CH, LPCM 5.1 & 7.1, DOLBY DIGITAL, DTS 5.1, DOLBY DIGITAL PLUS, DOLBY TRUEHD, DTS-HD
MASTER AUDIO, DTS-X, DOLBY ATMOS
DISTANCE:
HDBASET DISTANCE C4K & HOR)| 40 METERS <131 FEED CCAT 6A)
HDBASET DISTANCE <FULL HD)| 70 METERS (230 FEED CCAT 6A)
HDMI LEAD IN/OUT| UP TO 50 FEET CUSING BULLET TRAIN HDMD
HDMI LEAD IN/OUT CW/ AOC CABLE)| UP TO 130 FEET CUSING BULLET TRAIN AOC)
OTHER:
BANDWIDTH| 10.2 GBPS
CEC| YES
HDCP| HDCP 2.3 AND EARLIER
PORTS:
HDMI CTX & RX)| TYPE A
HDBASET| RJ45 W/ POH FOR HDBASET RECEIVERS
IR RX| 3.5MM STEREO C3 CONDUCTOR)
IR OUT & I-PASS| 3.5MM MONO (2 CONDUCTOR)
RS232| 3.5MM STEREO C3 CONDUCTOR)
ENVIRONMENTAL:
OPERATING TEMPERATURE| 23 TO 125°F C-5 TO 51°Cl
STORAGE TEMPERATURE| -4 TO 140°F (-20 TO 60°C)
HUMIDITY RANGE| 5-90% RH CNO CONDENSATION)
POWER CONSUMPTION CTOTAU| 7.5 WATTS MAX
---|---
POWER SUPPLY – MATRIX| INPUT: AC 100-240V ~ 50/60HZ OUTPUT: DC 48V .5A
DIMENSIONS:
DIMENSIONS CTX/RX ONLY, HEIGHT/DEPTH/WIDTH)| MM: 12.7 X 80 X 100.3
INCH: 0.5 X 3.15 X 3.95
DIMENSIONS (PACKAGED HEIGHT/DEPTH/WIDTH)| MM: 90 X 135 X 155
INCH: 3.54 X 5.31 X 6.1
WEIGHT (UNIT)| 0.68 LBS C0.31 KG)
WEIGHT <PACKAGED)| 1.74 LBS C0.79 KG)
*SPECIFICATIONS SUBJECT  TO  CHANGE  WITHOUT  NOTICE.  MASS & DIMENSIONS ARE  APPROXIMATE

Transmitter Overview

If the BLUE HDMI SIGNAL LIGHT is flashing, check the following:

•  The source. Plug it directly into the display to be sure it’s functioning properly.
• Try a longer HDMI cable. Some HDMI cables do not sync well at shorter lengths, a 2 meter minimum is recommended per HDMI Specifications.
• Set the EDID to state #1 (See Page[s] 12).
• Contact AVProEdge if these suggestions do not work.

STATUS – On front by HDMI Port: (Blue) This indicator shows that the HDMI source is connected. The states are:

• Light Is On (Solid) = Sync w/ HDMI source is correct and solid.
• Light Is Flashing = The light flashes during the sync process. If it is flashing continuously, a picture may not be present.

If the BLUE HDMI SIGNAL LIGHT is flashing, check the following:

• The source. Plug it directly into the display to be sure it’s functioning properly.
• Try a longer HDMI cable. Some HDMI cables do not sync well at shorter lengths, a 2 meter minimum is recommended per HDMI Specifications.
• Set the EDID to state #1 (See Page[s] 11).
• Contact AVProEdge if these suggestions do not work.

LINK above the RJ45 (HDBaseT) Port : (Green) This indicator shows that the HDBaseT link between the Tx and Rx is intact. This light should ALWAYS be solid. If this light is flashing or not present attempt the following:

• Check the length. The maximum distances are 40m (131ft) on 4K and 70m (230ft) on 1080P.
• Remove any coils of cable and make sure that there is not excess cabling.
• Bypass all patch panels and punch-down blocks.
• Re-terminate connectors. Sometimes, even if a cable tester indicates the run is valid, something may be slightly off.
• Contact AVProEdge if these suggestions do not work.

Status above the RJ45 (HDBaseT) Port : (Amber) This indicator shows that theres power present between the Tx and Rx. This light blink steadily indicating everything is OK. If you do not see this light attempt the following:

• Check the length. The maximum distances are 40m (131ft) on 4K and 70m (230ft) on 1080P.
• Remove any coils of cable and make sure that there is not excess cabling.
• Bypass all patch panels and punch-down blocks.
• Re-terminate connectors. Sometimes, even if a cable tester indicates the run is valid, something may be just slightly off.
• Try powering from the Receiver instead of the Transmitter
• Contact AVProEdge if these steps do not work.

Powering the System Bi-Directional Power: The AC-EX70-UHD-KIT allows you to choose where you power the kit. There are two options:

• Powering at the HDBaseT Tx – The power will be supplied to the Rx through the CAT cable.
• Powering at the HDBaseT Rx – The power will be supplied to the Tx through the CAT Cable (This is known as “Reverse Power)
  

NOTE: There is no button or switch to set the Power Mode. Simply plug the power supply into the Tx or Rx and the kit will electronically know what to do.

Indicator Troubleshooting Lights – Receiver

POWER – On the back by power HDBaseT RJ45 port: (Red) This is an indicator that the power is connected. There are only two states for light:

• Light Is On = Power supply is connected and functioning.
• Light Is Off = Power supply is not connected or there is no power present. In order to have power, check the power supply, USP, Outlet, etc.

STATUS – On front by HDMI Port: (Blue) This indicator shows that the HDMI source is connected. The states are:

• Light Is On (Solid) = Sync w/ HDMI source is correct and solid.
• Light Is Flashing = The light flashes during the sync process. If it is flashing continuously, a picture may not be present.

If the BLUE HDMI SIGNAL LIGHT is flashing, check the following:

• The source. Plug it directly into the display to be sure it’s functioning properly.
• Try a longer HDMI cable. Some HDMI cables do not sync well at shorter lengths, a 2 meter minimum is recommended per HDMI Specifications.
• Set the EDID to state #1 (See Page[s] 12).
• Contact AVProEdge if these suggestions do not work.

IR Configuration

There are three different 3.5mm IR ports located on the Transmitter and Receiver.

In the example below an IR receiving eye is plugged into the “IR IN” port of the HDBaseT Transmitter, and a IR Emitter is plugged into the “IR OUT” port of the HDBaseT Receiver. This allows you to use an IR Remote control to send and IR signal from the source side (TX) down the category cable to the sync (RX) and control the display.

IPASS – This port is designed to be directly connected to a control system via a 3.5mm Mono cable

NOTE : IPASS is only an INPUT. So you can go IPASS in from a control system to IR OUT.

Control System > IPASS (TX) ——IR OUT (RX)
Control System > IPASS (RX) ——IR OUT (TX)

In the example below a control system is plugged into the “IPASS” port of the HDBaseT Transmitter with a 3.5mm mono cable, and a IR Emitter is plugged into the “IR OUT” port of the HDBaseT Receiver. This allows you to send an IR signal from a control system down the category cable to the sink (RX) and control the display.

Default out of the box all the dip switches are down (off) “BYPASS (HDBT)”mode. This will pass the EDID of the connected display to the source un-altered.
NOTE: This is a 10.2Gbps extender, when in “BYPASS (HDBT)”make sure the source is not sending a signal that exceeds this HDBaseT Extender set. See bandwidth chart located on page[s] 14 for more information.

EDID Copy Instructions

Set the 4 DIP switches to 1 1 1 1 (all Up/On) with the connected sink (display) powered on. This will copy and store the downstream EDID from the sink (display) onto the Transmitter. This will stay until the above procedure is repeated. All 4 DIP switches do not need to be moved at the same time, mov- ing them individualy or in any combination will copy the EDID from the connected sink device.

RS-232 Configuration

For extending RS-232 communication over the Category cable. For these to pass a signal, both the Transmitter and Receiver need to have the Dip Switch set to Normal Mode, not RS-232 Program.
Default out of the box is MODE NORM (Normal Mode).
RS232 PROG (Program mode for Firmware updating).

Troubleshooting

• Verify Power – Check that the power supply is properly connected and on an active circuit.

• Verify Connections – Check that all cables are properly connected.

• TX/RX Indicator Troubleshooting Lights – Pg. 5-6

• IR Issues – Verify correct connections – P. 8-9
  Note: Visibly flashing Emitters may not function properly, if you are experiencing issue try the IR Cables that come in the box.

• Lights indicate everything is good but still not getting a picture, this may be a bandwidth limitation. See Bandwidth Chart below to verify the signal is not exceeding the bandwidth of the Extender kit (limited to 10.2Gbps).

Bandwidth Chart

Maintenance

To ensure reliable operation of this product as well as protecting the safety of any person using or handling this device while powered, please observe the following instructions.

• Use the power supplies provided. If an alternate supply is required, check voltage, polarity and that it has sufficient power to supply the device it is connected to.
• Do not operate these products outside the specified temperature and humidity range given in the above specifications.
• Ensure there is adequate ventilation to allow this product to operate efficiently.
• Repair of the equipment should only be carried out by qualified professionals as these products contain sensitive components that may be damaged by any mistreatment.
• Only use this product in a dry environment. Do not allow any liquids or harmful chemicals to come into contact with these products.
• Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner or benzene to clean this unit.

Damage Requiring Service

The unit should be serviced by qualified service personnel if:

• The DC power supply cord or AC adapter has been damaged
• Objects or liquids have gotten into the unit
• The unit has been exposed to rain
• The unit does not operate normally or exhibits a marked change in performance
• The unit has been dropped or the housing damaged

Support

Should you experience any problems while using this product, first, refer to the Troubleshooting section of this manual before contacting Technical Support. When calling, the following information should be provided:

• Product name and model number
• Product serial number
• Details of the issue and any conditions under which the issue is occurring
• Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner or benzene to clean this unit.

Warranty

If your product does not work properly because of a defect in materials or workmanship, AVProEdge (referred to as “the warrantor”) will, for the length of the period indicated as below, (Parts/Labor (10) Years), which starts with the date of original purchase (“Limited Warranty period”), at its option either (a) repair your product with new or refurbished parts, or (b) replace it with a new or a refurbished product. The decision to repair or replace will be made by the warrantor. During the “Labor” Limited Warranty period there will be no charge for labor. During the “Parts” warranty period, there will be no charge for parts. You must mail-in your product during the warranty period. This Limited Warranty is extended only to the original purchaser and only covers product purchased as new. A purchase receipt or other proof of original purchase date is required for Limited Warranty service.

This warranty extends to products purchased directly from AVPro or an authorized dealer. AVPro is not liable to honor this warranty if the product has been used in any application other than that for which it was intended, has been subjected to misuse, accidental damage, modification or improper installation procedures, unauthorized repairs or is outside of the warranty period. Please direct any questions or issues you may have to your local dealer before contacting AVPro.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>