Haier HWM80-316S6 Top Load Fully Automatic Washing Machine Owner’s Manual

Haier HWM80-316S6 Top Load Fully Automatic Washing Machine

OWNER’S MANUAL

HWM80-316S6; HWM90-316S6; HWM100-316S6; HWM120-316S6

Please read this manual carefully before operating your washing machine and retain it for future reference.

Product overview

Please understand the shapes of the washing machine and accessories may be different from the sketch figures in this manual due to product improvement.

Safety precautions

Description of symbols

Warning sign

Contents marked with this symbol are related to the safe use of  the product and the personal safety of the user.
Please operate in accordance to the contents of this manual, to avoid harm to the user or damage to the machine itself.

Forbidden sign

Contents marked with this symbol indicate operations or actions that should not be undertaken by the user.
Performing of such actions may result in an injury to the user damage to machine itself.

Safety warning

Please check power socket condition to ensure it has been earthed correctly prior to installation to ensure your safety.

Warning

Safety precautions

Safety precautions

Installation and adjustment

Please install and adjust the machine according to the directions contained in this manual.It is very important to follow these directions for the safe operation of the machine,and to ensure your machine operates correctly.

Install the bottom plate

Balance washing machine

Installation and adjustment

Usage of the drain hose

Inlet hose connection

The new hose-sets supplied with the appliance are to be used and that old hose-sets should not be reused.

Confirm the water faucet

Installation and adjustment

Connection between the water inlet hose jointer and the water faucet

1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the water inlet hose component. See to Figure 1.
2.Take off the nameplate. Make sure the threading is 4mm above the upper surface of the nut. See to Figure 6. If the threading is less than 4mm above the upper surface of the nut. please loosen the screws.

3.Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet. See to Figure 2.(If the faucet is too large and the jointer can not be set on the water faucet,please loosen the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth, otherwise it may leak water. See to Figure 3.)
4.Fasten the four screws evenly. See to Figure 4.
5.Twist the fastening nut, See to Figure 5. After installation, the threading is less than 2mm above the upper surface of the nut. See to Figure 6.

Connection between the water inlet hose and the washer

1. Do not take off the water absorption cushion.
Please check if the cushion is dropped or damaged before each usage.If it happens please contact our after-sale department immediately.
2. Put the nut of the water inlet hose on the valve jointer.
3. Fasten the nut. Swing it gently to confirm if it’s suitable.

Installation and adjustment

Connection between the jointer

Check the connection

1.Swing the hose gently to confirm if it is fastened stable.
2.After installation, open the faucet to check if it leaks.
3.Do not bend the hose with overstrain.
4.Before each usage please check if the connection between the jointer of the water inlet hose and the water faucet, and the installation of the water inlet hose are firm, so as to prevent dropping off.

Dismantle the water inlet hose

1.Close the water faucet.
2.Press the locking lever. Push down the slider.Then pull off the water inlet hose.
\If the machine is used frequently, the jointer of the water inlet hose.

Before washing

Check the following before washing

a. Check if the laundry has any special washing instructions.
b. Divide the laundry into colour fast.
c. Separate items that do not absorb water easily and wash by hand.
d. For heavily soiled items,please first remove loose dirt,then apply detergent directly (as per instructions on pack) to the stain before washing.
e. For those items that may attract lint or are furry or fluffy, please turn inside out before washing.
f. Do not put laundry soiled with chemicals or solvents into the washing machine.

Operation

Loading your laundry

• The rated washing capacity refers to the largest dry weight of a load that can be washed.

• The thickness, size and type of clothes will influence the actual capacity.
  Do not select more than water level “4” for clothes less than 1.0kg, to avoid splashing of water.

• It is recommended that low suds/high efficiency washing powder should be used.

Usage of the detergent

How to use liquid detergent

Before washing put the liquid detergent into the liquid detergent box directly by following the volume indication on the liquid detergent package.

How to use softener

• The usage and dose of the softener as per the specifications of softener.
• Before washing put the softener into the detergent box directly. See the above figure. The softener will put into the washer when the last rinsing.
• After the softener is put in, please don’t place for a long time otherwise softener may solidify .
• When water pressure is too low, it is possible that softener cannot be washed away effectively, and softener would be agglomerated after a period of time. Please clean the softener box in time. It is recommended to pour the softener into the basket directly after water is filled at the last rinse.

How to use washing powder

• When washing powder is added, remove part 1 as shown in figure 1 (HWM100-316S6、HWM120-316S6)

• It is suggested to dissolve powder before adding to the tub,see as below: It is suggested:
  1.Prepare warm water (<35°C) in a container.
  2.Add washing powder,stirring to dissolve it completely.

• Adding washing powder Normal Wash

• It is recommended that washing powder/liquid is dissolved with water and then directly emptied into the washing machine:
  1.Add some water (select the”1″ water level)
  2.Add washing powder/liquid. Run for about 30 seconds to fully dissolve the detergent. Then press the”Start/Pause” button to pause the wash cycle.
  3.Load laundry. Select suitable water level. Press the “Start/Pause” button again to recommence washing cycle.

• If you select “Quick” program, it is recommended to use liquid detergent instead of washing powder to ensure the most effective wash results.

• Old or poor quality washing powder may causing caking in tub or detergent dispenser.

• Clean the detergent box periodically to ensure washing power is evenly distributed and remove any detergent build up.

• When water pressure is too low, it is possible that washing powder or washing liquid cannot be washed away effectively, and washing powder or washing liquid would be agglomerated after a period of time. Please clean the detergent box in time. It is recommended to pour the washing powder or liquid into the basket directly.

Explanation of buttons

Indicator display

Child Lock function

• The function is intended for children safety and preventing children from accidental changes to washing programs.
• Press Power button,set the desired washing program,after setting, press Start/Pause button, then press Process button and hold for 3 seconds, The digitron displays “CL”, the child lock will activate. All of the buttons are locked and have no function.
• Release the child lock function:press Process b utton and hold for more than 3 seconds After three beep sound, the child lock function is release.The child lock light goes out.

Digital display

“Power” botton

“Start/Pause” button

“Program” select

“Process” button

[ PROCESS ]

The user can press “Process” button to select “Water level” , “Soak time”, “Wash time” , “Rinse time” , “Spin time” , and the after selection,they can push “Set” button to freeze the setting.

“Set” button

[ SET ]

Press the “Set” button,User can adjust “Water level” , “Sock time”, “Wash time” , “Rinse times” , “Spin time” , “Delay time”.

Tub clean

• Hold “Set button” 3 s econds to select the tub clean procedure.
• You can use this function to clean the inner tub and outer tub of washing machine.
• Spin alternately, and the total soak time is 10 hours to make sure better clean effect.
• Do not put clothes during tub clean process.

Delay

• Delay refers to the total time required for the program to run after the user has set the delay.
• Hold “Program” button 3 seconds, the digital displays “00” and the reservation indicator light. When pressing other buttons to set parameters and select programs, exit the delay setting mode. If no operation is done in 3 seconds in the reservation setting mode, exit the delay setting mode.
• Tub clean can not select Delay.

Button Operation and Descriptions

Cycle completed

When the machine has completed the selected/current wash cycle an audible alarm will be heard and the machine will automatically switch off.

Cleaning and Maintenance

Maintenance

• Remove the power plug before carrying out any cleaning or maintenance.
• Clean the lint filter(s) and detergent box afte r each wash,otherwise it may influence you using the machine.

Clean the deterge nt box
1.Pull it out gently.
2.Use a brush clean it, then flush it with water.
3.Install it qently and push it in.

The filter at the water inlet valve may become blocked by impurities in the water supply.Clean it with a plastic bristled brush every two months or if no water inlet.

• The lint filter must be used during washing.
• It must be cleaned in time after each using.

The mehods of dismantle and install lint filter as follows:

1. Push down spring piece of the top lint filter to make the claws out of the filter cover,and then pull out the lint filter to get it down.(figure1)
2. Push the back of the lint filter,and then you can get down it off the front cover of the lint filter.(figure2)
3. Sweep the lint in the lint filter.
4. Put the back of the lint filter into the front cover.
5. Put the lint filter into filter cover,and make it tight.
6. Make sure the lint filter well installed,or it can influence your use.

If the cabinet is dirty,wipe it with a damp cloth

• Do not wash directly with water.
• Wipe with a neutral detergent(please check directions on detergent bottle first).
• Do not wipe machine with thinners, petrol, alcohol or other hash solvents.

1. After washing cycle has finished,turn off the water faucet.(If needed,you can remove the water inlet hose).
2. Do not store water in the washing machine for a long period without completing a wash cycle.Drain the water completely after each wash.
3. Hang up the power cord and drain hose.
4. Wipe up any drops of water on the surface of the machine and inside the tub.Leave the lid open for about 1 hour after each wash to evaporate any residual water.

Trouble-shooting

If there is a fault or the machine does not operate correctly,remove the power plug before checking the machine.Using diagnostic list below,please check if the machine requires repair.If a repair is required, please contact our customer care team,do not try to fix it by yourself.

Packing list

Specification

Specifications

• Model Numbers: HWM80-316S6, HWM90-316S6, HWM100-316S6, HWM120-316S6
• Product Overview: Top Load Fully Automatic Washing Machine
• Components: Detergent box, Outer tub cover, Control panel seat, Top lid component, Inner tub, Lint filter, Pulsator, Cabinet, Adjustable feet (2 pieces), Water inlet valve, Back cover, Handle, Power cord, Fixed feet (2 pieces), Drain hose, Base frame
• Power Supply: Earthed power socket required
• Intended Use: Household and similar applications

FAQ

Q: Can I use hot water with this washing machine?

A: Do not connect the machine to hot water higher than [specify temperature limit in manual].

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>