Pyle PDIWCS56 Ceiling Wall Mount Enclosed Speaker User Guide
- June 4, 2024
- Pyle
Table of Contents
Pyle PDIWCS56 Ceiling Wall Mount Enclosed Speaker
Introduction
Thank you for purchasing this PYLE in-wall/in-ceiling speaker system. It is a state-of-the-art product carefully designed and manufactured for your installation needs, and has been thoroughly tested to ensure consistent and reliable performance.
If you have any question about the installation or operation of your PYLE in- wall/in-ceiling speaker system which are not answered by this manual, contact your dealer immediately.
INCLUDED
IN-CEILING SPEAKERS
SPEAKER PLACEMENT
FRONT SPEAKERS
INSTALLATION
The in-wall/in-ceiling speakers were designed to be easily installed. However, if you are unsure of your ability to properly install these loudspeakers please contact your dealer or a qualified installer. please contact your dealer or a qualified installer.
TOOLS NEEDED
TROUBLESHOOTING
IF THERE IS NO SOUND FROM ANY OF THE SPEAKERS:
- Check that receiver/amplifier is on and a source is playing.
- Check all wires and connections between receiver amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured or touching each other.
- Review proper operation of your receiver/amplifier.
IF THERE IS NO SOUND COMING FROM ONE SPEAKER:
- Check the “Balance” control on your receiver/amplifier.
- Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed, cut, punctured or touching each other.
IF THERE IS LOW (OR NO) BASS OUTPUT:
- Make sure the connections to the left and right “Speaker Inputs· have the correct polarity{+ and-).
- Consider adding a powered subwoofer to your system.
- In Dolby Digital Of DTS modes. make sure your receiver/processor is correctly configured. When using a subwoofer, make sure the subwoofer output of the receiver/ processor has been enabled. If no subwoofer is being used, make sure the left and nght front and rear speakers have been configured as “LARGE.” See your receiver/processor’s owner”s manual for futner information on correct speaker configuration in Dolby Digital, DTS and other surround sound modes.
IF THE SYSTEM PLAYS AT LOW VOLUMES BUT SHUTS OFF AS VOLUME IS INCREASED:
- Check all wires and connections between receiver/amplifier and speakers. Make sure all wires are connected. Make sure none of the speaker wires are frayed. cut, punctured or touching each other.
- If more than one pair of main speakers is being used, check the minimum impedance requirements of your receiver/amplifier.’
WIRING DIAGRAM
REAR SPEAKERS
IN-CEILING
Proper placement of the speakers is an important step in obtaining the most realistic soundstage possible. These recommendations are for the optimum placement of the loudspeakers. Use these placement recommendations as a guide. Slight variations will not diminish your listening pleasure. The front speakers should be placed the same distance from each’ other as they are from the listening position. They should be placed at about the same height from the floor as the listener’s ears will be, with the tweeters aimed toward the listener at ear-level height. In a home theater configuration, the two surround speakers should be placed slightly behind the listening position and ideally should face each other and be at a level higher than the listener’s ears. If that is not possible, they may be placed in a wall (or in the ceiling) behind the listening position, facing forward. The surround speakers should not call attention to themselves. They should provide a diffuse, ambient sound accompanying the main program material heard in the front speakers. In Dolby Digital and DTS systems, aim the tweeters toward the listening position at ear-level height.
SPEAKER CONNECTIONNS
CONNECTION TIPS
The wires for both speakers should be the same length. If one speaker is placed closer to the amplifier than the other, hide the excess wire behind the wall. Speakers and electronics terminals have corresponding (+) and (-) terminals. We use red to denote the (+) terminal and black for the (-) terminal. It is important to connect both speakers identically: (+) on the speaker to (+) on the amplifier and -) on the speaker to (-) on the amplifier. Wiring “out of phase” results in thin sound, weak bass and a poor stereo image. With the advent of multi-channel surround sound systems, connecting all of the speakers in your system with the correct polarity remains equally important in order to preserve the proper ambience and directionality of the program material.
EXISTING CONSTRUCTION
IN-CEILING SPEAKERS
-
Cut the drywall.
Note : Always allow at least one-half inch between a wall stud and the speaker cutout the locking tabs will not be able to swivel into place. -
Connect the speaker wires to the speaker.
-
Place the frame assembly in the wall
-
Screw down each of the four Phillips head screws. The locking tabs will swivel into place and secure the unit to the rear surface of the drywall. Put in the strips of adhesive to secure the grille. The in-celling speakers feature unique swivel mounts for the tweeters that enable you to aim the very directional high frequencies toward the listening position, at ear-level height. Before installing the speaker grile, gently press on the outer edge of the tweeter mount to adjust the position of the tweeter. The tweeter will not swivel more than 15 degrees in any direction; do not attempt to force it to move further.
-
Replace the metal grille
After installing the speaker grille, gently press on the mesh of the tweeter to adjust the position of the tweeter.
- MODEL NO. PDIWCS56
- Cut-out Dimensions: 14″(w) x 6.4″(H) x3″(D)
- Dimensions (each speaker) 6″(w)x7.6″(H)x3.6″(D)
Frequently Asked Questions
How can I connect an amplifier to Pyle PDIWCS56 ceiling speakers?****
Drill a hole for the wires. After ensuring sure the amplifier is unplugged, turn the breaker off. Install the wiring. Start connecting the wires to the ceiling speaker terminals. The terminals of the amplifier should receive the other end of the cables. By enabling your breaker, you may test it out.
Are there any power requirements for the Pyle PDIWCS56 ceiling speakers?****
No, ceiling speakers normally function as passive speakers, meaning that they are driven by speaker wires connected to an external amplifier because they lack built-in amplifiers. The amplifier is connected to each ceiling speaker using binding posts.
Can I connect my TV to my Pyle PDIWCS56 ceiling speakers?****
There will be an audio output on every TV. For the time being, it will most likely be a digital optical output. By connecting an analogue wire from your TV to the amplifier and turning on line output on your TV, you may listen to TV sound through your ceiling speaker system.
The Pyle PDIWCS56 ceiling speakers produce good sound, right?****
In actuality, it’s a great idea to play music over ceiling speakers. By immersing you in surround sound, they can simulate being at a symphony hall or live event.
When using the Pyle PDIWCS56 ceiling speakers, can surround sound be used?****
Ceiling speakers are a great option if you want a home theatre experience with a more immersive audio experience. They must be specifically designed for ceilings, but they are still a great addition to a surround sound system.
Is power provided to Pyle PDIWCS56 ceiling speakers?****
Passive speakers are frequently mounted on walls and ceilings. As a result, they are not needed to be connected to a power source. They merely need to be connected to a receiver or amplifier with a power source in order to function.
Dolby Atmos and Pyle PDIWCS56 in-ceiling speakers work together?****
Most ceiling speakers are compatible with Atmos. The majority of speaker options, including those for the ceiling, are compatible with Dolby Atmos if you’re building your own home theatre; however, some of the older models might not be able to support this surround sound application.
Can ceiling speakers like the Pyle PDIWCS56 be installed in a wall?****
In-ceiling speakers can be used in place of in-wall speakers, and their audio output is fairly similar. The biggest difference will be in size. In-wall speakers are typically larger than in-ceiling speakers.
The Pyle PDIWCS56 ceiling speakers are suitable for rear surround, correct?****
The answer is no if your amplifier can handle surround sound doubt yes
How can I connect a pair of Pyle PDIWCS56 ceiling speakers to a receiver?****
Turn off all of the lights. Put your cords in order. Trim the ends of the wires. Look at the speaker wiring diagram. As soon as your wires arrive, plug them into the proper sockets. Cable locks are used to secure the sockets.
Can you watch TV with Pyle PDIWCS56 ceiling speakers?****
There will be an audio output on every TV. For the time being, it will most likely be a digital optical output. By connecting an analogue wire from your TV to the amplifier and turning on line output on your TV, you may listen to TV sound through your ceiling speaker system.
Does the sound coming from the Pyle PDIWCS56 ceiling speakers sound good?****
In reality, playing music over ceiling speakers is a terrific idea. They can make you feel like you’re at a concert hall or live performance by completely enveloping you in surround sound.
What in-ceiling speakers are superior to the Pyle PDIWCS56?****
As a result, in-wall speakers usually have superior quality and power than in- ceiling speakers. When in-wall speakers are installed in multiple walls of a room or another area, they can add more sound dimensions than just a downward- firing one.
Is Pyle PDIWCS56 ceiling speakers subwoofer-required?****
Even if ceiling speakers can handle all of the frequencies, a subwoofer will be helpful in handling the bass and low-end ones. Additionally, it significantly improves the overall sound quality of your sound system.
How do in Pyle PDIWCS56 ceiling speakers get power?****
No, ceiling speakers typically operate as passive speakers, which means that, because they lack built-in amplifiers, they are powered by speaker wires connected to an external amplifier. Each ceiling speaker is connected to the amplifier using the binding posts.
Can you put ceiling speakers in a wall, like the Pyle PDIWCS56?****
In-wall speakers can be replaced with in-ceiling speakers, and the sound they produce is very comparable. The size difference will be the most obvious. Typically, in-wall speakers are bigger than in-ceiling speakers.
What are the workings of the Pyle PDIWCS56 Bluetooth ceiling speakers?****
Wirelessly controlling Bluetooth ceiling speakers is usually done with a smartphone or other internet-enabled device. The Bluetooth chip in the speaker will pick up the content from the smartphone and play it through the speaker.
Does the Pyle PDIWCS56 ceiling speaker system have bass?****
There is never a bass response point and a background sound field with in- ceiling speakers. For the environment, they were created.
How are the Pyle PDIWCS56 ceiling speakers measured?****
Take your measurements in inches for the speaker using a ruler or a tape measure. The biggest portion of the cone should face upward while your speaker is standing upright. Measure the distance between the mounting frame’s two edges at the speaker’s widest point. So that you won’t forget the measurement later, write it down.
Can I utilize ceiling speakers for surround sound, such as the Pyle PDIWCS56?****
If your amplifier can handle surround sound, then the answer is without a doubt yes.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>