Einhell TC-PT 2500 Pallet Lifting Truck User Manual

Einhell TC-PT 2500 Pallet Lifting Truck

Danger

When using the equipment, a few safety precautions must be observed to avoid injuries and damage. Please read the complete operating instructions and safety regulations with due care.
Keep this manual in a safe place, so that the information is available at all times. If you give the equipment to any other person, hand over these operating instructions and safety regulations as well. We cannot accept any liability for damage or accidents which arise due to a failure to follow these instructions and the safety instructions.

Safety regulations

Danger!

Read all safety regulations and instructions.

Any errors made in following the safety regulations and instructions may result in an electric shock, fi re and/or serious injury.

Keep all safety regulations and instructions in a safe place for future use.

• Pay attention to the accident prevention regulations.
• Never exceed the specified payload.
• Do not use the pallet lifting truck until you have familiarized yourself with its mode of operation and been trained and instructed on how to use it.
• Check the equipment for damage and make sure that it is in good working order each time before you use it.
• Do not use the pallet lifting truck on uneven ground or slopes.
• The pallet lifting truck has no brake. It is not allowed to be used on upward or downward inclines.
• Wear work gloves and safety shoes.
• It is imperative to stay clear of the area under lifted loads.
• The load you want to transport must be distributed evenly over the lifting forks.
• Never transport loosely piled loads or unstable loads.
• The pallet lifting truck is not allowed to be loaded when the lifting forks are in a raised position.
• Loads on raised lifting forks must never be left unattended.
• Do not reach into moving parts.
• Do not transport people.
• Keep a minimum distance of 60 cm from other persons when transporting loads.
• The work area must be well illuminated.

Layout and items supplied

Layout (Fig. 1)

1. Handle
2. Control lever
3. Drawbar
4. Hydraulic unit
5. Steering rollers
6. Lifting forks
7. Load-bearing rollers (tandem)
   

Items supplied

Please check that the article is complete as specified in the scope of delivery. If parts are missing, please contact our service center or the sales outlet where you made your purchase at the latest within 5 working days after purchasing the product and upon presentation of a valid bill of purchase. Also, refer to the warranty table in the service information at the end of the operating instructions

• Open the packaging and take out the equipment with care.
• Remove the packaging material and any packaging and/or transportation braces (if available).
• Check to see if all items are supplied.
• Inspect the equipment and accessories for transport damage.
• If possible, please keep the packaging until the end of the guarantee period.

Danger!

The equipment and packaging material are not toys. Do not let children play with plastic bags, foils or small parts. There is a danger of swallowing or suffocating!

• Pallet lifting truck
• Drawbar
• Clamp sleeve
• Bolt
• Original operating instructions

Proper use

The equipment is designed for transporting goods on pallets with an open base or with stringer boards extending beyond the load wheels. The equipment must be used on a firm, flat surface. It is prohibited to use the equipment to pick up or transport people

Ambient temperature of -20°C to +40°C.

The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the manufacturer will be liable for any damage or injuries of any kind caused as a result of this.

Technical data

Overall height: ……………………………….. 1210 mm
Overall length: ……………………………….. 1500 mm
Fork length: …………………………………… 1150 mm
Fork height min.: ………………………………… 80 mm
Fork height max.: ……………………………… 190 mm
Fork width single: …………………………….. 153 mm
Fork width total: ……………………………….. 540 mm
Lift max.: ………………………………………… 110 mm
Load: ………………………………………………..2500 kg
Weight approx.: …………………………………….62 kg
Steering wheels Ø: …………………………… 180 mm
Load-bearing rollers Ø: ……………………….. 80 mm

Assembly

Note: The hydraulic system is secured with a bolt (M). Do not remove it until prompted in the following assembly description and keep it in a safe place for future maintenance work.

1. (Fig. 1) Press down the control lever (2) as far as it will go into the lowering position (see 6. Functions).

2. (Fig. 2) Pass the control chain (F) through and out of the recess at the bottom end of the drawbar.
   

3. (Fig. 3) Insert the bolt (B) through the hole in the drawbar mount (C) and the hole in the drawbar. Make sure that the clamping sleeve passage (E) coincides with the clamping sleeve hole in the bolt (B).
   

4. (Fig. 2) Pass the control chain (F) through the hole in the bolt (B) so that the hydraulics system works.

5. (Fig. 3) Hook the setting screw (H) with the pre-mounted hex nut (K) into the hydraulics lever (L).

6. (Fig. 3) Press the drawbar (3) down a little so that the hydraulics lock bolt (M) is slackened and can be removed.

7. (Fig. 4) Check whether the clamping sleeve mount of the bolt (B) coincides with the clamping sleeve passage (E) in the drawbar mount. Use a hammer and the hydraulics lock bolt (M) to hit the sleeves (A) into the bolt (B) on the left and right.

Note: The equipment can be optionally equipped with a foot-activated parking brake. If required, please contact your customer service team.

Operating the foot-activated parking brake: Push the brake to the right as far as the stop – the wheels will be blocked.

Push the brake to the left – the wheels will be released again.

Functions

Important! Note the safety information (section 1.) and Figure 6.
On the drawbar is a sticker showing the positions of the handle switch (Fig. 5).

1 = Lower (lowering position)
2 = Travel (traveling position)
3 = Lift (lifting position)

The pallet lifting truck is allowed to be parked only when the lifting forks are lowered.
The following functions are possible and were already set in the factory.

Lifting the load (Fig. 1)
Press down the control lever (2) (lifting position). Then pump the drawbar (3) up and down several times. The load will be lifted.
Pulling the load (Fig. 1)
Pull up the control lever (2) into the middle position (traveling position). In this position the hydraulics cannot be used for lifting or lowering.
Lowering the load (Fig. 1)
With the pallet lifting truck at a standstill, pull up the control lever (2) to the very top (lowering position). The load will be lowered. When you now release the control lever (2), it will automatically return to the middle position (traveling position).

Setting the hydraulics control system

The functions described in section 6. will not work correctly if the hydraulics control settings are altered. In this case you must re-set the hydraulics control system.

The lifting forks rise when the control lever is in the traveling position

(Fig. 3) Turn the hex nut (K) on the setting screw (H) clockwise to the point where the lifting forks no longer rise and the traveling position works correctly.

The lifting forks descend when the control lever is in the traveling position

(Fig. 3) Turn the hex nut (K) on the setting screw (H) counter-clockwise to the point where the lifting forks no longer descend and the traveling position works correctly.

The lifting forks do not descend when the control lever is in the lowering position

(Fig. 3) Turn the hex nut (K) on the setting screw (H) clockwise to the point where the lifting forks are lowered by pulling up the control lever. Then check the operation of the traveling position in order to guarantee that the setting nut is in the correct position.

The lifting forks do not rise when the control lever is in the lifting position

(Fig. 3) Turn the hex nut (K) on the setting screw (H) counter-clockwise to the point where the lifting forks are raised when the control lever is in the lifting position. Then check the operation of the traveling position and the lowering position in order to guarantee that the setting nut is in the correct position.

Cleaning, maintenance and ordering of spare parts

Cleaning

Use a damp cloth to clean the casing.

Servicing

The pallet lifting truck must be regularly inspected and if necessary serviced in order to keep it in good working order. All the repair and maintenance jobs which are not listed here must be carried out by a customer service center or an authorized specialist. This applies in particular to replacing the steering and load-bearing rollers.
If malfunctions arise, the pallet lifting truck must be taken out of operation immediately and be repaired by an authorized person. Only original spare parts are allowed to be used.
The pallet lifting truck must be inspected by an expert at least once a year or more often if necessary. It is recommended to record the inspections in an inspection book.
After carrying out repair or maintenance work, ensure that all safety parts are installed and in perfect condition.
Store potentially hazardous parts out of the reach of other persons and children.

Important: In accordance with the German Product Liability Act, we are not liable for any damages if they result from improper repairs to the product or if parts are replaced by items other than genuine parts or parts approved by us. Furthermore, we are not liable for any damages if they result from improper repairs to the product. Arrange for your customer service or an authorized workshop to do the work. The same applies to accessory parts.

Filling up with hydraulic oil

Check the oil level every six months. When filling up with hydraulic oil or replacing it, use only hydraulic oil from the viscosity classes HLP 46 (- 20 °C – + 40°C) . A complete filling equals approx. 0.4 liters.

Important! To prevent environmental contamination from escaping oil, use absorbent materials (e.g. wood chips, dry rags) promptly to pick up any oil spills. Take soiled maintenance material and operating materials to an appropriate collection point and dispose of the soiled material correctly

1. Lower the lifting forks as far as possible
2. Remove the oil filler plug and seal from the oil tank.
3. Fill in hydraulic oil up to the brim
4. Reinsert the oil filler plug and seal into the oil tank.
5. Vent the hydraulics system with several pumping movements of the drawbar

Venting the hydraulic unit

If the lifting forks do not rise when the control lever is in the lifting position, move the control lever into the lower position and move the drawbar up and down again several times.

Lubricating the moving parts

Lubricate and grease the moving parts regularly.

Ordering replacement parts:

Please quote the following data when ordering replacement parts:

• Type of machine
• Article number of the machine
• Identification number of the machine
• Replacement part number of the part required For our latest prices and information please go to www.Einhell-Service.com

Disposal and recycling

The equipment is supplied in packaging to prevent it from being damaged in transit. The raw materials in this packaging can be reused or recycled. The equipment and its accessories are made of various types of material, such as metal and plastic. Never place defective equipment in your household refuse. The equipment should be taken to a suitable collection center for proper disposal. If you do not know the whereabouts of such a collection point, you should ask in your local council offices.

Storage

Store the equipment and accessories in a dark and dry place at above freezing temperature. The ideal storage temperature is between 5 and 30 °C. Store the electric tool in its original packaging.

Troubleshooting

If the equipment is operated properly you should experience no problems with malfunctions or faults. In the event of any malfunctions or faults, please check the following before you contact your customer services.

hydraulic oil Change the hydraulic oil Set the setting nut (K) (see section 7.) Vent the hydraulic unit (see section 8.)
The lifting forks cannot be lowered| The piston rod or pump housing has been damaged by overloading or an uneven load distribution The piston is stuck The setting nut (K) is set wrongly| Replace the piston rod or pump housing Replace the piston Set the setting nut (K) (see section 7.)
Leaks| The seals are worn or damaged The hydraulic module is defective| Replace the seals Replace the hydraulic module
The lifting forks descend without the relief valve working| The hydraulic oil is dirty The hydraulic module is defective Air in the hydraulic unit The seals are worn or damaged The setting nut (K) is set wrongly| Change the hydraulic oil Replace the hydraulic module Vent the hydraulic unit (see section 8.) Replace the seals  Set the setting nut (K) (see section 7.)

Important!

This work must be performed by qualified and approved specialists.

The reprinting or reproduction by any other means, in whole or in part, of documentation and papers accompanying products is permitted only with the express consent of the Einhell Germany AG.

Subject to technical changes

Warranty certificate

Dear Customer,

All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that this equipment develops a fault, please contact our service department at the address shown on this guarantee card. You can also contact us by telephone using the service number shown. Please note the following terms under which guarantee claims can be made:

1. These guarantee terms apply solely to consumers, i.e. natural persons, who do not want to use this product in connection with either their commercial or other self-employed activities. These guarantee terms regulate additional guarantee services which the undermentioned manufacturer promises to buyers of its new products in addition to their statutory rights of guarantee. Your statutory rights of guarantee are not affected by this guarantee. Our guarantee is free of charge to you.
2. The guarantee services cover only defects due to material or manufacturing faults on the new product which you have bought in the European Union from the undermentioned manufacturer and are limited to either the rectifi cation of said defects or the replacement of the product, whichever we prefer. Please note that only equipment under the brand name “Professional” has been designed for use in commercial, trade or professional applications. For all other products the guarantee is invalidated if the equipment is used within the guarantee period in commercial, trade or industrial applications or for other equivalent activities.
3. Our guarantee does not cover:
   • Damage to the equipment caused by failure to comply with the installation/assembly instructions or by unprofessional installation; damage caused by failure to comply with the operating instructions (e.g. connection to the wrong mains voltage or current type); damage caused by failure to comply with the maintenance and safety regulations; damage caused by exposing the equipment to abnormal environmental conditions; damage resulting from poor care and maintenance.
   • Damage to the equipment caused by misuse or incorrect applications (e.g. overloading the equipment or using non-approved attachments or accessories); damage caused by foreign bodies (e.g. sand, stones, dust, ….) getting inside the equipment. Damage in transit; damage caused by force or external influences (e.g. by dropping the equipment).
   • Damage to the equipment or parts of the equipment which is owed to use-related, normal or otherwise natural wear. For example, batteries and battery packs are manufactured with a cycle limit for design related reasons. Wear is negatively influenced in particular by load demands and charging speeds as well as exposure to heat, cold, vibration and impact.
4. The guarantee is valid for a period of 2 years starting from the purchase date of the equipment. Guarantee claims must be submitted before the end of the guarantee period and within two weeks of the defect being noticed. No guarantee claims will be accepted after the end of the guarantee period. The original guarantee period remains applicable to the equipment even if repairs are carried out or parts are replaced. In such cases, the work performed or parts fitted will not result in an extension of the guarantee period, and no new guarantee will become active for the work performed or for any replacement parts fitted. This also applies if on-site service is used.
5. To assert your guarantee claim, register the defective equipment at: www.Einhell-Service.com. You will need to provide proof of purchase of the new item of equipment. Equipment returned without such proof or without a rating plate are excluded from the guarantee services because of the lack of traceability. If the defect is covered by our guarantee, then either the item in question will be repaired immediately and returned to you or we will send you a new replacement.
6. If you have taken the equipment with you to a different EU country than where you bought it, we will arrange for a local service partner to provide the guarantee services. If you take the equipment outside the EU, the guarantee will not apply.

Of course, we are also happy to offer a chargeable repair service for any defects which are not covered or no longer covered by the scope of this guarantee. To take advantage of this service, please send the equipment to our service address. We draw attention to the restrictions of this guarantee concerning wear parts, consumables and missing parts as presented in the service information included in this operating manual.

Warrantor/ Service:

Einhell UK Ltd, Unit 10, 1st Floor, Champion‘s Business Park, Arrowe Brook Road, Upton, Wirral, CH49 0AB

 ISC GmbH · Eschenstraße 6 · D-94405 Landau/Isar

Declaration of Conformity

explains the following conformity according to EU directives and norms for the following product

Pallet truck TC-PT 2500 (Einhell)

 2014/29/EU
 2005/32/EC_2009/125/EC
 2014/35/EU
 2006/28/EC
 2014/30/EU
 2014/32/EU
 2014/53/EC
 2014/68/EU
 90/396/EC_2009/142/EC
 89/686/EC_96/58/EC
 2011/65/EU
2006/42/EC
Annex IV
Notifi ed Body:
Notifi ed Body No.:
Reg. No.:
2000/14/EC_2005/88/EC
Annex V
Annex VI
Noise: measured LWA = dB (A); guaranteed LWA = dB (A) P = KW; L/Ø = cm Notifi ed Body:
2012/46/EU
Emission No.

Standard references: EN ISO 3691-5: 2014

Landau/Isar, den 10.03.2015

Brunhölzl/Leiter Produkt-Management

Landauer/Produkt-Management

References

• Einhell Service
• service.com is for sale | www.brandforce.com
• Einhell Service
• Strumenti di alta qualità per gli amanti del Fai da Te e del giardinaggio | Einhell.it

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>