weatherables 4-Rail Horse Fence Installation Guide

weatherables 4-Rail Horse Fence

Product Specifications

This 4-rail Horse Fence from Weatherables can be trimmed down in width to accommodate custom applications. All dimensions are in inches (“).

• Height: 96.00″
• Rail Thickness: 0.150″
• Post Thickness: 0.090″
• Ground Concrete Footing Required

Installation

Before starting the installation process, ensure you have checked local codes and guidelines.

Step 1: Preparing the Post Holes

1. String your fence line and dig your first post hole: 10-12″ wide x 32-36″ deep.
2. Dig subsequent holes at 96″ intervals, ensuring proper spacing and alignment.
3. For Fast2K installation, adjust hole dimensions as recommended.

Step 2: Setting the Posts

1. Insert posts into holes and secure with concrete or Fast2K alternative.
2. Mix and pour concrete ensuring posts are straight and aligned properly.
3. Verify correct spacing between the ground and bottom rail (up to 11″).

Step 3: Attaching the Rails

1. Insert rails into the posts following the recommended sequence.

Step 4: Finalizing Installation

1. Straighten and level posts as necessary.
2. Pour additional concrete if needed and insert post-hole covers.
3. Repeat the steps for the entire fence line.

If you require additional materials or assistance during installation, please contact us at 1-888-743-3673.

FAQ

Q: Can this fence be customized for different widths?

• A: Yes, this fence can be trimmed down in width to accommodate custom applications.

Q: What is Fast2K and how can it simplify the installation process?

• A: Fast2K is a concrete alternative that is easier to use and set compared to traditional concrete.
• It can be used wherever concrete is required in the installation process.

Welcome

• A beautiful finish that always looks new.
• Thank you for choosing the 4-Rail Horse Fence from Weatherables. Rest assured that your new fence will provide years of durable performance and maintenance-free satisfaction.
• This guide will help make your installation easy. For questions, please call 1-888-743-3673 and welcome to Weatherables.

Product Specifications

This fence can be trimmed down in width to accommodate custom applications

Check the local code before installing.

Installation

Important Reminders:

• We recommend installing 1 post and section at a time but other methods work too. Alter this method to suit your installation needs.
• Before construction, check with your regulatory agency for special code requirements in your area.
• Contact your utility supplier to locate and mark underground lines before excavation.
• Sketch out the layout of your fence and calculate the number of panels, gates, and posts required (for a fence run, one extra post kit is needed).
• Careful planning and measuring of your fence is essential. Keep in mind that moving posts after the concrete sets is extremely difficult.
• Fast2k Tip! Wherever concrete is used in installation, use Fast2K instead to simplify the process.
• Fast2K is a concrete alternative that is much easier to use and set.

1. String your fence line and begin by digging your first post hole: 10”-12” wide x 32”-36” deep.
   • Fast2K Tip! For Fast2k install, dig a hole 6” wide x 32” deep.
2. Dig your second hole 96” on center to your first hole, your third hole 96” on center to your second hole, and so on. Be sure to dig only 3-4 holes at a time to ensure proper spacing.
3. Insert post A into the hole and set concrete. Post B may be loosely laying in the hole until the panel is fully installed. Repeat the process down the line.

  *  **Fast2K Tip!** Add one 12.4 oz. bag to the hole. Hold the post in place to prevent movement and follow mixing instructions on the bag. Pour around the post and plumb during expansion.
2. To set posts in concrete, hold a post in place and prevent movement to ensure the post stays straight. Be prepared to use a minimum of (1) 60lb. bag of concrete for each post hole.
3. Mix concrete and pour wet.
4. Pour concrete into the hole and plumb. Fill any remaining space with soil. Lastly, verify the spacing between the ground and the bottom rail is correct (up to 11”).
  1. Insert rails into post A and then into post B.
  2. Straighten and level post B.
  3. Pour in mixed concrete.
  4. Insert post-hole covers into unused holes of a post. Repeat steps down the line.
  5. If more material is needed, please call 1-[888-743-3673](https://phone.gd/phone/888-743-3673).![weatherables-4-Rail-Horse-Fence-fig-6](https://manuals.plus/wp-content/uploads/2024/03/weatherables-4-Rail-Horse-Fence-fig-6.jpg)

We’re happy to help. Call 1-888-743-3673.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>