DPS MY-PS-2 Digital Phase Converter Instruction Manual

DPS MY-PS-2 Digital Phase Converter

Specifications

• Model Name: MY-PS-2
• Features:

1. DPS can run a 3-phase motor with a single-phase
2. Very easy to connect DPS and motor
3. Small size & lightweight
4. Digital Type Phase Converter
5. Keeps out dust, moisture, and heat due to the sealed type
6. Excellent start-up torque
7. Efficiency is excellent versus other phase converters
8. Low failure rate
9. Designed to be non-flammable
10. Does not generate any high-frequency
11. Lower power consumption

• Country of Origin: Made in Korea

Product Usage Instructions

DPS Installation Diagram

• Applied Motor: AC 220V 1HP (0.75kW) 3A
• Voltage: AC 200V-240V
• Input Phase: Single-Phase
• Frequency: 50Hz/60Hz
• Output Phase: Three-Phase
• Output Current: 3A
• Output Frequency: 50Hz/60Hz
• Efficiency: 90-95%

Product Usage Guidelines

A. Proper Selection and Usage

• DPS must be selected based on the motor specifications including rated current, horsepower, and voltage. Use the MY-PS-2 model for 200V-240V 1HP 3-phase motors.

B. Single Motor Usage

• Each DPS unit should be used for only one motor to ensure proper operation and avoid issues.

Frequently Asked Questions (FAQ)

Q: Can DPS be used with motors of different power ratings?

• A: It is recommended to match the DPS model with the specific motor’s horsepower and voltage ratings to ensure optimal performance and prevent potential issues.

Features

1. DPS can run a 3-phase motor with a single-phase
2. Very easy to connect DPS and motor
3. Small size & lightweight
4. Digital Type Phase Converter
5. Keeps out dust, moisture, and heat due to the sealed type
6. Excellent start-up torque
7. Efficiency is excellent versus other phase converters
8. Low failure rate
9. Designed to be non-flammable
10. Does not generate any high-frequency
11. Lower power consumption

Country of origin: Made in Korea

DPS install diagram

Technical data

Dimension and weight

DPS model selection table

CAUTION

1. DPS must be appropriately selected and used according to the motor specifications.
   • Check the motor’s rated current (A), horsepower (HP), and voltage (V) and select the DPS model.
2. MY-PS-2 model should be used on a 200V-240V 1HP 3-phase motor.
   • If used on a motor with a horsepower lower than 1HP(for example 0.5HP, 0.25HP motor), the motor may generate heat, make noise, and cause problems with motor operation.
3. DPS must be used for only one motor. One DPS should never be used on multiple motors.
4. DPS can make 200V-240V 3-phase from 200V-240V single-phase.
5. The voltage of the motor must be set to 200V-240V(delta wiring).
6. The efficiency is around 90% when using a DPS model that matches the electric motor specifications.
7. The thickness of wires should be suitable for motor-rated current.
8. DPS does not operate on a 3-phase motor installed with a 3-phase brake.
9. DPS creates induced three phases by running a motor. Therefore, three phases can be measured at the DPS output when the motor is running. If the motor is not running, you cannot measure any three phases at the DPS output.
10. If a magnet contactor is connected to the motor and DPS, you must connect two control wires which are from the magnetic contactor to ‘U’ and ‘W’ of the DPS output. If the motor does not work even though the power is turned on after connecting the DPS and the motor, please switch the wires positions of “U”, “V” and “W” for DPS’s output at least 3 times If the motor operates in reverse rotation and the positions of the ‘U’ and ‘W’ wires of the DPS output are swapped, the motor operates in forward rotation.
11. If your machine has a magnetic contactor, it must be 220V only. DPS cannot work for a 380V or 440V magnetic contactor.
12. When the motor initially starts and there is not much load on the motor, the current on the ‘U’ and ‘W’ phases of the DPS output may become imbalanced.
    • However, when more than 50% load is applied to the motor, the ‘U’ and ‘W’ current values are balanced. The ‘V’ phase is approximately equal to the motor’s rated current value.
13. If the current is imbalanced even when the load on the motor is more than 50%, check whether the DPS model settings are correct. DPS has a set of available models depending on the specifications of each motor.
    • If you use a DPS higher than the motor specifications, the motor may generate heat or noise. Also, please check whether the motor is overloaded. DPS efficiency is around 90%. In general, the three phases supplied by power companies and the three phases produced by DPS are different. This is because DPS converts from single-phase to three-phase. Therefore, please use the motor with an efficiency of 90% or less.
14. In general, the ‘V’ phase of DPS ‘U-V-W’ has a current value lower than the motor’s rated current. And, U and W change depending on the load of the motor.
    • For example, when the motor rated current is 15A and the ‘V’ phase of the ‘U-V-W’ of the DPS output exceeds 15A, there is a high possibility that the motor is overloaded or used incorrect DPS model or problem in the environment around the motor.
    • If the current in the ‘V’ phase is higher than the motor-rated current, heat may be generated in the motor.

• MYUNG YOUN ELECTRONICS CO., LTD.
• Address: 59, Pyongcheon-ro, Bupyeong-gu, Incheon, Republic of Korea
• E-mail:sales01@myungyoun.com
• Website:www.myungyoun.com
• Tel: +82 32 330 1510 Fax: +82 32 330 1514

Documents / Resources

| DPS MY-PS-2 Digital Phase Converter [pdf] Instruction Manual
MY-PS-2 Digital Phase Converter, MY-PS-2, Digital Phase Converter, Phase Converter, Converter
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>