COSTWAY NP10795 Gas Fire Table User Manual
- June 2, 2024
- COSTWAY
Table of Contents
COSTWAY NP10795 Gas Fire Table
USER MANUAL
Gas Fire Table
NP10795
THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
Before You Start
- Please read all instructions carefully.
- Retain instructions for future reference.
- Separate and count all parts and hardware.
- Read through each step carefully and follow the proper order.
- We recommend that, where possible, all items are assembled near to the area in which they will be placed in use, to avoid moving the product unnecessarily once assembled.
- Always place the product on a flat, steady and stable surface.
- Keep all small parts and packaging materials for this product away from babies and children as they potentially pose a serious choking hazard.
WARNING
-
The installation of this unit must adhere to local codes or Propane Storage and Handling Code, CSA B149.2.
-
THIS UNIT IS INTENDED FOR OUTDOOR USE ONLY! This product shall be used outdoors, in a ventilated space and shall not be used in any enclosed area.
-
This unit is to be used with propane gas only! (sold separately)
-
Do not attach a remote gas supply to this unit.
-
Only use propane gas for this unit.
-
Solid fuels shall not be burned in this appliance.
-
When igniting this unit, stay away from the burner as the flame will light up and may cause injury.
-
LP GAS WARNING: Do not use any more than 1/4in depth lava rocks/pumice stones/LavaGlass® above the burner holes. Doing so will suffocate the flame.
-
If the propane gas tank is leaking gas, you may hear, see, or smell a hiss. Do the following:
1. Disconnect the propane gas tank.
2. Do not attempt to fix the problem yourself.
3. Contact professional or fire department for help. -
Applying too much propane may result in gas pooling and will not burn. Allow fresh air into the unit so that the remaining gas may escape.
-
Do not use a flame to check for gas leaks.
-
Manifold pressure: 11 inches w.c. (2.74kPa).
-
Use LP propane tanks with the following dimensions: diameter 12 in, height 18 in – capacity 20 lbs.
-
You must use a propane tank that has a collar to protect the gas valve.
-
DO NOT fill tank over 80 percent full.
-
The tank system must be set up for vapor withdrawal.
-
Discontinue use if any part of the propane tank is damaged. Rust and dents may be hazardous and should be inspected by a gas supplier.
-
Do not burn anything other than the provided materials for this fire table.
-
Keep away from the unit for the first 20 minutes after igniting your unit for the first time, as lava rocks/pumice stones/L avaGlass® could pop out and cause injury. Should any rocks pop out, discard them.
-
Always ensure that lava rocks/pumice stones/LavaGlass® are completely dry before use. Failure to do so will cause them to crack or pop.
-
Do not operate unit until all parts are fully assembled.
-
Do not paint or color any part of this heating unit.
-
Unit may be hot while in use, do not attempt to move it while in use.
-
Never leave this heating unit unattended while in use.
-
This unit is not intended for cooking.
-
Keep any flammable items away and do not use any other fireplace cover for this unit.
-
Keep a safe distance to avoid burning skin or clothing.
-
Do not sit or rest hands or feet on this heating unit.
-
Never place hands or fingers on upper portion of this unit while in use.
-
Keep all electrical cords and fuel supply hose away from heated surfaces.
-
Combustible material should not be within 60 inches of the top of the unit, or within 48 inches around the entire unit.
-
Keep the appliance area clear and free from combustible material, gasoline and other flammable vapors and liquids.
-
If the flame goes out while burning, turn the gas valve off. Wait 5 minutes before repeating the initial lighting procedure. Once you have a flame started, hold down the control knob for 1 minute.
-
Do not add water into the unit.
-
Do not operate unit if any part has been under water. Immediately call a qualified service technician to inspect the appliance and replace any part of the control system and any gas control that has been under water.
-
Do not disconnect any part while unit is in use.
-
Do not store a spare propane tank on or near this unit.
-
If the heating unit is indoors, detach the propane tank and leave outdoors.
-
Do not operate on a boat or vehicle. This unit must be used on a flat surface and outdoors ONLY.
-
Always remove protective cover before operating (if applicable).
-
Do not set the protective cover over the unit until it is turned off and completely cooled down.
-
Check for leaks after not using the unit for long periods of time.
-
Children should never operate this unit. Children must be supervised while near this unit.
-
Keep gas tank at least 5 feet away from unit when lit. (if external tank)
-
Maximum gas supply: 250 psi; Min. gas supply: 10 psi.
-
All installation and repair should be done by a qualified professional. This unit should be inspected annually and cleaned regularly.
-
Inspect all elements of this heating unit before each use. If there is damage, the burner must be replaced.
-
Keep the hose out from any pathways to eliminate any accidental damage. (if external tank)
-
Be aware of the hazards of high temperatures and stay away from the unit to avoid any burns or injury.
-
The gas supply tank should be constructed and marked with the specifications for the LP gas tanks of the U.S. Department of Transportation or the National Standard of Canada CAN/CSA- B339, LP gas tanks, spheres and tubes for Transportation of Dangerous Goods.
-
The LP gas tank must have a listed overfilling prevention device and a QCCI or Type I, (CGA791) LP gas tank connection.
-
This heating appliance should not be used on plastic or artificial wood decks.
-
Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition.
-
Young children should be carefully supervised when they are in the area of the appliance.
-
Clothing or other flammable materials should not be hung from the appliance or placed on or near the appliance.
-
Any guard or other protective device removed for servicing the appliance shall be replaced prior to operating the appliance.
-
Installation and repair should be done by a qualified service person. The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required as necessary. It is imperative that the control compartment, burners and circulating airways of the appliance are kept clean.
IF APPLICABLE:
- Allow heating item to cool completely before placing on lid.
- DO NOT use heating item while lid is installed. Always remove the lid while heating item is in use.
Only use the regulator and hose assembly provided with this unit. Replacement
parts must be supplied directly by the manufacturer.
Inspect the burner before use of this unit. If the burner shows any kind of
damage, do not operate the appliance. For assistance with repair or
replacement of the burner or any other parts, please contact COSTWAY.
NOTE: You must follow all steps to properly assemble this heating item. Make sure the gas valve is turned “OFF” before assembling. Do NOT attempt to assemble without proper tools.
Don’t lock the screws until the assembly is complete.
Attach the door (A) and legs (B,C) to the table top using 4 pcs M6*12mm screws.
Note: Please don’t lock the screws first.
Attach the panels (D,E,F) to the legs (A,B,C) using 12 pcs M6*25mm screws.
Note: Please don’t lock the screws first.
Attach the metal stand between the panels (D,E) using 4 pcs M6*25mm screws.
Note: Please lock all screws.
Attach 4 pcs foot pads (N) on the legs (A,B,C) by rotating clockwise the foot pads.
Place the table lid (I) on the table top (H).
Put a propane gas tank (not included) into the metal stand (G). Make sure the gas tank sits on the metal stand (G) completely. Turn the outer pre-assembled wing screw of metal stand (G) clockwise to secure the propane gas tank tightly.
Turn the cylinder valve on the tank clockwise to close the propane tank. Turn the regulator coupling nut clockwise to attach the pre-assembled regulator from the table top (H) to the cylinder valve. Make sure it is fastened securely and tighten connections by hands only. Finally fix the gas hose to the bracket that is inside the front panel.
Open the igniter cover and put AAA battery (P) into it, then tighten the igniter cover completely.
Pour the cashew lava rocks (K) around the burner. Ensure cashew lava rocks (K) is not placed on the ignition portion of the burner.
CAUTION
To ensure proper function , the guard on this burner should be free of lava
rocks at all times.
When the gas furnace is not used outside, it should be covered with a protective cover (J) to prevent the product from oxidization caused by exposure to sun and rain.
Before performing a leak test, be sure that no sparks can occur and you are in a spacious outdoor area. Connect the propane gas tank to the regulator and turn the valve on the unit to the “off” position. Brush a soap and water mixture on all connections. Turn the gas supply on; if bubbles occur on any connection there may be a leak. If you smell gas or a leak is discovered turn the gas valve off, disconnect propane gas tank and do not use the appliance until the leak is repaired.
Don’t use the heating unit without inspecting the gas hose. If there are signs of wear or abrasion you must replace the hose (if applicable). Pumice stones/lava rocks/LavaGlass® could pop up and strike somebody’s face during the process of lighting this unit; stand away from the unit for the first 20 minutes after igniting. Flame height should be a yellow/blue color between 2 – 10 inches in height.
Wait 50 minutes after extinguishing flame prior to placing a lid (if applicable) or protective cover on heating item.
To Light
1. Make sure the control knob is in the “OFF” position.
2. Open the door and slowly open the valve on the propane gas tank by turning
the knob counterclockwise.
3. Close the door on the body.
4. Push the ignition control knob in fully and rotate about 1/4 turn
counterclockwise until a click is heard, it may take several attempts to light
the burner. Once lit, keep holding down the control knob for 15 seconds.
5. If ignition doesn’t occur within a few seconds, release the control knob
and rotate to the “OFF” position. Wait for 5 minutes for gas to clear and then
repeat the above lighting instructions.
6. To adjust the flame, turn the control knob either clockwise or
counterclockwise depending on whether you want to lower or raise the flame.
To Extinguish
1. Turn control knob clockwise to the “HIGH” position; push and continue
turning the control knob to the “OFF” position.
2. Close the cylinder valve on the propane gas tank if you don’t intend to
use it for a long time.
- Before performing any maintenance always disconnect propane gas tank.
- Store your product indoors during winter months. Avoiding extreme cold temperatures will prevent exposure damage.
- Keep the heating item free and clear from combustible materials.
- Visually inspect burner for obstructions and keep tank enclosure free and clear from debris.
- Use a soft brush to get rid of the mild stains, loose dirt and soil after the burner and pumice stones/ lava rocks/LavaGlass® are completely cooled down. Wipe down with a soft cloth.
- Harsh weather conditions may cause stubborn stains, discoloration and possibly rust pitting.
- Permanent damage may occur if powder or solvent comes in contact with painted or plastic components on this heating unit.
- Keep the heating unit stored away from direct sunlight.
- If storing this unit inside, disconnect the propane gas tank from the gas valve.
- Not using manufacturer approved or supplied parts/accessories may result in a defective condition and void the warranty of this heating unit.
- Always place lid (if applicable) or protective cover on heating item when not in use.
Problem | Cause | Solution |
---|---|---|
Heating unit won’t light | Igniter pin and burner are wet | Dry off with a soft |
cloth
Igniter battery is incorrectly inserted| Check which direction the battery is
inserted
Igniter pin is broken| Contact COSTWAY for a replacement part
Electrode wire is loose or disconnected| Reconnect wire to the igniter box
located inside the fire pit behind the igniter box
Electrode wire is shorting between valve and igniter pin| Contact COSTWAY for
a replacement part.
Burner won’t light while using a match| No gas flow| Check that the gas tank
isn’t empty
Regulator isn’t connected securely to the tank| Tighten regulator connection
to the gas tank
Gas flow is obstructed| Check all hoses for kinks and bends
Burner ports are clogged| Turn all gas flow connections off. Insert an opened
paperclip (or similar item) into each of the burner ports to clear them out.
Heating unit emits a lot of black smoke| Flame is obstructed at burner ports|
Check that all burner ports are free of any small lava rocks/pumice
stones/LavaGlass® pieces
---|---|---
Sudden drop in gas flow| No gas flow| Check that the gas tank isn’t empty
---|---|---
Excess flow safety valve has been activated| Tum the control knob to the ‘off’
position. Close the tank valve and disconnect propane gas tank. Turn the
control knob to ‘high’; wait 1 minute. Turn the control knob back to the ‘off’
position. Reconnect propane gas tank. Light the fire unit as indicated in the
‘To Light’ section of this manual.
Flame blows out easily| High or gusting winds| Increase flame to ‘high’
No gas flow| Check that the gas tank isn’t empty
Excess flow safety valve has been activated| See ‘sudden drop in gas flow’
above
Return / Damage Claim Instructions
- DO NOT discard the box / original packaging.
- In case a return is required, the item must be returned in original box. Without this your return will not be accepted.
- Take a photo of the box markings.
- A photo of the markings (text) on the side of the box is required in case a part is needed for replacement. This helps our staff identify your product number to ensure you receive the correct parts.
- Take a photo of the damaged part (if applicable).
- A photo of the damage is always required to file a claim and get your replacement or refund processed quickly. Please make sure you have the box even if it is damaged.
- Send us an email with the images requested.
- Email us directly from marketplace where your item was purchased with the attached images and a description of your claim.
USA office:
Fontana AUS office: Truganina GBR office: Ipswich FRA office: Saint Vigor d’Ymonville
If you’re having difficulty, our friendly customer team is always here to help.
USA:cs.us@costway.com
AUS:cs.au@costway.com
GBR:cs.uk@costway.com
FRA:cs.fr @costway.com