LONGCONN ELECTRONICS W326 3 in 1 Charging Station for Apple Devices User Manual

LONGCONN ELECTRONICS W326 3 in 1 Charging Station for Apple Devices

Product Overview

• what’s in the Box:
• Samba Pad Pro Wirless Charger *1
• Power Adapter *1
• User manual *1
  

Specifications

Technical Parameters

Compatibility

Connecting

1. Put the power adapter plug into the groove.
   

2. Insert the power adapter plug into the DC jack.
   

3. Rotate the cable into the groove.
   

4. Use the AC adapter to power the wireless charger.
   

5. Charge your devices.
   
   

iPhone Charging Mode Setting

Pad Mode Lay the device flat on the charging pad. This mode is compatible with some devices without Mag Safe (device must be centered on the charging pad).
|

1. Pry from the groove on the side of the charging Pad to lift it up.
2. Pull the charging pad up, you can use the Hover mode.
   

| Hover Mode.
In this mode, you can adjust the angle of the iPhone at will, and even rotate it at will. In this mode, you can adjust the angle of the iPhone at will, and even rotate it at will.
Tips: It is highly recommended to charge your device in this mode. Charging is faster in hover mode as it is more conducive to cooling. And easier to place and remove your device.

---|---|---

Apple Watch Charging Mode Setting

Watch Flat Mode Lay your Apple Watch flat on the magnetic charging module, Easy to use.
| Jack up the watch charging assembly from the back till it is upright. The Apple Watch is ready to use nightstand mode.
| Nightstand Mode.
Turn on the nightstand mode of Apple Watch.

---|---|---

LED Indicator

Important Safety Instructions

• Avoid dropping.
• Do not disassemble.
• Do not expose to liquids.
• Only use the original power adapter.
• This product is suitable for moderate climates only.
• The maximum ambient temperature during use of this product must not exceed 40°C.
• Open flame sources, such as candles, must not be placed on this product.
• Only use a dry cloth or brush to clean this product.

Attention

• Do not put anything else between your smartphone and the wireless charger such as credit cards, door keys, coins, metal, NFC cards, etc.
• Make sure to place the device in the center of the charging pad. Improper placement may result in heat generation or non-charging.
• Compatible only with iPhones with MagSafe.
• Please use a MagSafe compatible case, or no case. Cases that are not MagSafe compatible will not provide enough magnetism for positioning.
  

Tips: The charging speed is related to the ambient temperature.
for fast charging, please place the wireless charger in a cool and ventilated place. for example, a cool room, or near a fan or air conditioner. Do not expose it to direct sunlight; or place it near hot objects. Such as electrical appliances, heating, fireplaces, etc.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC warning:

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Model :W326
Manufacturer: LONGCONN ELECTRONICS (SHENZHEN) CO LTD

Made in China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>