legrand LERAK136-FRENIT EV Charging Station Mounting Kit Instruction Manual

June 2, 2024
Legrand

legrand LERAK136-FRENIT EV Charging Station Mounting
Kit Green’up One
0 570 18
Installation Manual

Introduction

  • The mounting kit is designed for the EV charging stations 0 570 10, . … .., 0 570 17.
  • The pedestal is double-sided, so you can install one or two charging stations to it.

Safety instructions

Electrically skilled person

  • The installation must only be done by a qualified professional.
  • Read this Installation Manual carefully before you start the installation work.
  • Obey the instructions in this Installation Manual, and make sure that the installation complies with national safety regulations, installation methods and restrictions.
  • The information provided in this Installation Manual in no way exempts the installer or user from responsibility to obey all applicable safety regulations.
  • This Installation Manual is a part of the product and must be stored in a safe location so that it is available for future installation and service.

WARNING

Danger of electric shock! Risk of fire!

  • Improper installation can cause personal injury and property damage.
  • Do not switch on the power supply before the installation work is completed.

Description of symbols

**| WARNING – Indicates a hazard with a medium level of risk which, if not avoided, could result in death or serious injury or considerable damage to the equipment.
---|---
**
| Electrically skilled person
****| Environmental instructions

Delivery content

  • Pedestal
  • Mounting accessories
  • Installation Manual

4.1. Pedestal

  • The pedestal is applicable for mounting on ground or floor.
  • Inside the pedestal is a metal conduit Ø 60mm for electrical cable routing and a compartment for possible electrical connections.

legrand LERAK136-FRENIT EV Charging Station Mounting Kit -
PedestalAttach the bottom plate to the pedestal:

  • Remove the pre-installed fastening screws 4 pcs from the pedestal.
  • Attach the bottom plate to the pedestal with the screws you removed.

4.2. Mounting accessories

Item Description and use Quantity
Screw M5x20
•Attach the charging station to the pedestal 2
Screw M5x10
•Fasten the pedestal to a pole (e.g. car heating pole) 4
Branching connector max. 4 connections
•Branch LI, L2., L3 and N 4
Branching connector max. 6 connections
•Branch PE 1
Cover plug for M32 opening
•Close the cable entry at the bottom of the charging station I
Membrane entry grommet for 16mm hole
•For ethernet cable when installing two charging sta- Lions 1
Grommet M16 for cable 0 5-9mm
•For ethernet cable 2

legrand LERAK136-FRENIT EV Charging Station Mounting Kit - Item
8| Grommet M32 for cable 0 15-20mm
•For supply cable| 2
| Cover cap for MS screw head
•Cover fastening screws inside the charging station| 4

Mounting instructions

5.1. Before installation
Remove the pedestal from its package. Do not scratch the surface of the item after removal from the package.
When selecting installation site, take into account the following:

  • You need accessories applicable for the mounting site and method.
  • The charging station is applicable for indoor and outdoor use.
  • To make sure the optimal charging performance, the charging station should not be exposed to direct sunlight.
  • The minimum space necessary for operating and maintenance.

legrand LERAK136-FRENIT EV Charging Station Mounting Kit - Mounting
instructionsObey always national regulations and site requirements
5.2. Cable entries
Open cable entries on the rear of the charging station to route electrical cables to the charging station.
Disassemble the chargerlegrand LERAK136-FRENIT EV Charging Station
Mounting Kit - Disassemble the charger Prepare the charger for mountinglegrand
LERAK136-FRENIT EV Charging Station Mounting Kit - Prepare the charger for
mounting 5.3. Disassemble the pedestal
Installation steps
Keep the removed parts.
All the removed parts are necessary when you assemble the pedestal.legrand
LERAK136-FRENIT EV Charging Station Mounting Kit - Disassemble the
pedestal 5.4. Attach the charging station to the pedestal
Installation stepslegrand LERAK136-FRENIT EV Charging Station Mounting
Kit - Disassemble the pedestal 1

Installation instructions

  • A separate connection cable is necessary for the installation. Make sure that the connection cable complies with the system dimensioning.
  • Use the included connectors for installation.
  • Alternatively you can route the supply cable directly to the charging station.
  • If the charging station will be connected to the internet, first connect the Ethernet cable to the RJ45 connector and then the supply conductors to the power terminals.

6.1. Connection cable

legrand LERAK136-FRENIT EV Charging Station Mounting Kit - Connection
cable * The length is for the longest conductor. Cut the other conductors to applicable lengths.
Leave the ground conductor long enough so that if a fault occurs it is the last one that comes loose.
For more detailed wiring instructions please see the charging station’s Installation Manual.
6.2. Wiring example
The installation of two 1-phase charging stations to the pedestal
Tightening torque: 10 Nmlegrand LERAK136-FRENIT EV Charging Station Mounting
Kit - Wiring example
The installation of two 3-phase charging stations to the pedestal**
Tightening torque: 10 Nmlegrand LERAK136-FRENIT EV Charging Station Mounting
Kit - Wiring example 1

Mounting on concrete casting

Items needed:
Pedestal…………………..1 pcs
Anchor bolts M12 (not included) ………………4 pcs
Washers (not included)
Nuts (not included)
Make sure that the materials used for the concrete casting and the installation procedures obey local building regulations and safety standards.

  • Dig a trench for cable conduits and an excavation pit for the concrete foundation. The pit floor should be compacted and level.
  • Put cable and possible drain pipes in place.
  • Fill the pit with concrete.
  • Let the concrete cure. Make sure that the surface stays level during the process.

Installation steps

  1. Make sure that the concrete surface is compacted and level.
  2. Drill a hole in the concrete for the anchor bolts. For more in- formation, please see the anchor bolt instructions.
  3. Put the anchor bolts in place.legrand LERAK136-FRENIT EV Charging Station Mounting Kit - assembly 1
  4. Pull the electrical cables approx. 1600 mm measured from the concrete surface.
  5. Attach the pedestal on the anchor bolts with washers and nuts.
  6. Pull the electrical cables through the metal conduit in the pole.
  7. Attach the charging station to the pedestal. See instruc- tions on page 27.legrand LERAK136-FRENIT EV Charging Station Mounting Kit - assembly 2

Dimension drawings

legrand LERAK136-FRENIT EV Charging Station Mounting Kit - Dimension
drawings

Technical information

Electrical connections Mounting Kit
Nominal supply voltage 1-ph, 230 VAC / 3-ph, 400VAC
Nominal frequency AC 50 Hz
Supply connection to included connectors Cu 2,5 mm² – 16 mm² Tightening

torque: 10Nm
Connection cable| Cu 2,5 mm² – 6 mm² Ø 10 – 20 mm Stranded or solid conductors
Supply connection to charging station| See the charging station’s technical specifications
Design and Mechanics| Pedestal
---|---
Material| Aluminium
Color| Silver
Mounting| Ground / Floor
Weight| approx. 8,8 kg
Ingress protection rating| IP23
Impact resistance rating| IK10

Tested according to IEC 61439-07 medium resistance

Disposal

**** Do not dispose of electrical and electronic devices including their accessories with the household waste.

  • When the charging station is at the end of its life cycle, it must be disposed of properly according to local recycling guidelines.
  • The cardboard packing of the charging station can be recycled.
  • Dispose of the plastic wrap with the household waste or according to local recycling guidelines.

Installation / Commissioning checklist

Introduction
Examine the mechanical and electrical installation in accordance with this checklist to make sure that the charging station is properly installed.
Checking the Installation
Examine the visual, mechanical and electrical installation when the charging station is un-powered.

CATEGORY X ITEM
Overall look You have received the ordered material.
You do not see any scratches or damages.
Mechanical installation The charging station is fixed properly on the

installation site.
Electrical installation| | Charging station’s power supply capacity meets the electrical planning (cable size, protective devices…).
Review the local electrical design plan.
| The PE-cable screw is tight.
| The power supply conductors (L1, L2, L3, N and PE) are properly connected.
| The insulation of the power supply cable and the conductors (L1,1_2, L3, N and PE) is intact.
| TN /TT network:
•The voltage between PE and N is less than 10 V.
IT network:
•The voltage between LI and N is 230 V.
•The voltage between Ll and PE is 130 V.
| The PE conductor resistance is less than 3 O.
| Test the functionality of the protective device.

Legrand reserves at any time the right to modify the contents of this booklet and to communicate, in any form and modality, the changes brought to the same.

LEGRAND
Pro and Consumer Service
BP 30076 – 87002
LIMOGES CEDEX FRANCE
www.legrand.com

Documents / Resources

| legrand LERAK136-FRENIT EV Charging Station Mounting Kit [pdf] Instruction Manual
LERAK136-FRENIT-20230502, LERAK136-FRENIT EV Charging Station Mounting Kit, LERAK136-FRENIT, EV Charging Station Mounting Kit, Charging Station Mounting Kit, Station Mounting Kit, Mounting Kit, Kit
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals