GIGABYTE BRIX Ultra Compact PC Kit User Guide
- June 2, 2024
- Gigabyte
Table of Contents
- GIGABYTE BRIX Ultra Compact PC Kit
- Safety and Regulatory Information
- Package Contents
- Package Contents
- PRODUCT OVERVIEW
- A) M.2 SSD: How to Install the M.2 2280 SSD
- B) Memorv Installation: SO-DIMM DDR4
- C) Wireless Module: How to Safely Remove the Module
- VESA Bracket
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
GIGABYTE BRIX Ultra Compact PC Kit
Safety and Regulatory Information
- This product must be grounded with the plug on the adepter’s power cord connected toe power socket withe grounding connection
- Risk of explosion if the battery is replaced with an incorrect type. Batteries should be recycled where possible. Disposal of used Batteries must be in accordance with local environmental regulations.
- Before you open chassis to exchange an internal component, you need to power off the device and let the device cool down at least 10 minutes.
- CAUTION! Hot Surface. Do not touch.
Package Contents
Lieferumfang / Contenu du colis / C
Package Contents
- x GB-BN Bare-bone
NOT Include any of the following: M.2 (2280), SO-DIMM memory
PRODUCT OVERVIEW
- Power Button (#*F/281)
- USB 3.2 Gen2 Type A (10Gbps)
- USB 3.2 Gen2 Type C (10Gbps)(5V/3A)
- Headphone/Microphone (E1/35/a)
- DC-in (#intA)
- HDMI 2.0 (Support CEC)
- RJ-45 (10/100/1000/2500Mbps)
- USB 2.0 Type A x 3 (480Mbps)
- USB 3.2 Gen2 Type A x 1 (10Gbps)
- DP (support DP1.4/3840×2160@60Hz)
- Vent Hole (30 m. 7L)
- Kensington Lock Slot (B7*69**)
- VESA Screw Hole (#87L)
A) M.2 SSD: How to Install the M.2 2280 SSD
- Remove the small screw secured to the M.2 SSD slot B screw hole.
- Carefully insert the M.2 SSD into slot B.
- Insert the tab on the thermal plate into the slit near the connector, then secure the thermal plate and M.2 SSD in place with the previously removed screw.
NOTE!
The illustrations of the M.2 SSD/Heatsink installation shown are for
reference only. Please follow the installation steps of actual purchased.
B) Memorv Installation: SO-DIMM DDR4
- Carefully insert SO-DIMM memory modules.
- Push down until the modules click into place.
- Carefully insert SO-DIMM memory modules.
- Push down until the modules click into place.
C) Wireless Module: How to Safely Remove the Module
- Disconnect the two antennas by manually lifting off the clips that hold them in place.
- Remove the screw in the middle.
- Carefully pull the wireless module from the slot.
VESA Bracket
- Attach the screws provided on the underside of the svstem.
- Attach the VESA mounting plate to the rear of a compatible display using the screws provided.
- The system can now be mounted by sliding the device into place.
NOTE! The illustrations of the VESA bracket installation shown are for reference only. Please follow the installation steps of actual purchased bracket.
Restricted substances and its chemical symbols
- Note 1 : “Exceeding 0.1 wt%” and “exceeding 0.01 wt%” indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition.
- Note 2 : “ ” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence.
- Note 3 : The “-” indicates that the restricted substance corresponds to the exemption.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>