THE HOME DEPOT 23213-000 3 ft. Brushed Nickel Integrated LED Fixed Track Lighting Kit with Dimmable Dual Bar Instruction Manual
- June 4, 2024
- THE HOME DEPOT
Table of Contents
THE HOME DEPOT 23213-000 3 ft. Brushed Nickel Integrated LED Fixed Track
Lighting Kit with Dimmable Dual Bar
IMPORTANT SAFETY INSTRUCTIONS
Read and Save:
-
To reduce the chance of fire or electrical shock: Do not install non-factory wiring or any other electrical components. Altering or modifying the lamp in any way will render the lamp unsafe.
-
Keep curtains, shades, wall hangings and all other fabrics and objects away from the lamp canopy, lamp shade and light bulb. Unit is not designed to support additional weight. Do not hang objects from the lamp or any lamp part.
-
Before starting the installation, disconnect the power by turning off the circuit breaker or removing the appropriate fuse at the fuse box. Turning off the power at the light switch is not sufficient to prevent electrical shock.
-
This unit is suitable for damp locations.
-
Electrical Connections: All electrical connections must be in accordance with local codes, ordinances and the National Electric Code. If you are unfamiliar with methods of installing electrical wiring, secure the services of a qualified, licensed, electrician.
-
This unit is to be mounted to a metal electrical junction box (outlet box) directly supported by the building structure.
-
Tools and Materials Required: (Not Included) Flathead screwdriver, wire cutters, ladder, pliers, U.L./CSA listed electrical tape.
-
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment on and off, the user isencouraged to try to correct the interference by one or more of the following:
- Reorient or relocate the receiving antenna.
- ncrease the separation between the lighting unit and receiver.
- Connect the lighting unit into an outlet on a circuit other than the outlet which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for assistance.
NOTE: Please note that changes and modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. The party responsible name: Is lucidity Lights, Inc.
Address: Boston, MA 02129.
Internet contact information: http://www.luciditylights.com
-
Dimmable to 10% with recommended dimmers: Lutron Diva (DVCL-153PRWH), Lutron Skylark (CTCL-153PDH-WH), Lutron Toggler (TGCL-153PHWH), Lutron Maestro (MACL-153MH-WH), Lutron Caseta (P-PKG1WWH-R), Leviton Sure Slide (R62-06674-P0W), Leviton Decora (R12-06672-1LW), Leviton Illume Tech (R50-IPL06-10M), Eaton AL Series (AAL06-C1), Eaton Sky AL(SAL06P-LA-K).
LIGHT BULB REPLACEMENT
Integrated LED bulb replacement not required.
CLEANING AND MAINTENANCE
- Clean using a mild cleaning solution and a soft cloth.
- Never use a rough cloth or chemical cleaners containing acids, abrasives or solvents.
ASSEMBLY INSTRUCTIONS
-
Preparing the unit for installation
Carefully unpack and lay all parts on a clean, level surface. Unscrew the canopy nuts (C) from fixture assembly (B) and detach the mounting bracket (A). Attach the mounting bracket (A) to the junction box (not included) with junction box screws (AA). -
Make electrical connections to a 120V AC/60Hz circuit.
Lift up the fixture assembly (B) toward the ceiling. Connect the white wires from the fixture to the white wire of the supply circuit. Connect the black wires from the fixture to the black wire of the supply circuit. Wrap the bare copper grounding wire from the fixture around the green screw on the mounting bracket (A), then connect it to the grounding conductor of the supply circuit. Use U.L./C.S.A. listed wire connectors (BB) suitable for the size, type and number of conductors. Secure the wire connectors (BB) with U.L./C.S.A. listed electrical tape. Tuck all wires back into the Outlet Box. -
Installing the fixture
Place the fixture assembly (B) against the mounting surface, allowing the preassembled screws on the mounting bracket (A) to pass through the fixture assembly (B). Secure with previously removed canopy nuts (C). -
Position Adjustment
Adjust the head to your desired position. Restore electrical power when complete. Turn on lamp using the wall switch.
For Customer Assistance:
www.luciditylights.com
Made In China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>