GE current IND502 Lumination LED Luminaire Installation Guide

: June 4, 2024
: GE current

Table of Contents

BEFORE YOU BEGIN
Tools Required
Component List
Installation
FCC STATEMENT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

GE current IND502 Lumination LED Luminaire Installation Guide

BEFORE YOU BEGIN

Read these instructions completely and carefully.

WARNING

RISK OF ELECTRIC SHOCK

Turn power off before inspection, installation or removal.
Install this kit only in the luminaires that has the construction features and dimensions shown in the photographs and/or drawings.
Installation of this retrofit assembly requires a person familiar with the construction and operation of the luminaire’s electrical system and the hazard involved. If not qualified, do not attempt installation. Contact a qualified electrician.
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.

CAUTION

Fixture may fall down if not installed properly, follow installation instructions.
Wear safety glasses and proper aid during installation and maintenance.
Use only UL certified wire, wire connectors, minimum 18AWG, minimum rated 75°C.

Save These Instructions
Use only in the manner intended by the manufacturer.
If you have any questions, contact the manufacturer.

NOTE: LRX products are suitable for indoor covered ceiling wet location applications.

The retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by UL or authorities having jurisdiction.

Wear work gloves to prevent dirt and oil from being transferred to the luminaire.

Prepare Electrical Wiring

Electrical Requirements

The luminaire LRX***MDEL must be supplied with 120-277VAC, 50/60 HZ.
The luminaire LRX***PHEL must be supplied with 120VAC 50/60 HZ.
Connected to an individual properly groundedbranch circuit, protected by a 15 or 20 amperecircuit breaker. Use min. 75°C supply conductor.

Grounding Instructions
The grounding and bonding of the overall system shall be done in accordance with National Electric Code (NEC) Article 600 and local codes.

Fixture Requirements
The LED retrofit luminaire must be connected to the mains supply according to its ratings on the product label.

Tools Required

The components have been properly packed to avoid damage during transit. Inspect the components to confirm there is no physical damage. Do not install damaged components.

Component List

LRX EMBB Fixture
Installation Instructions

Installation

LRX EMBB fixture is one component of LRX EMBB new construction or retrofit system. Before install the fixture, please confirm that the required new frame or EMBB kit has been received already. Verify the junction box and bracket are metal and are constructed similarly to the illustration at below. For more detail on install process, please refer to the installations in LRX EMBB New Construction(IND342) and LRX EMBB Retrofit: LRXEMBBKIT07HE/LRXEMBBKIT07/ LRXEMBBKIT10(IND343).

LRX Round frame shown above.
Ensure that the power to the unit is turned off. Use proper lockout and tagout procedures.

Suitable Frame

| Bracket| Hole| Suitable Fixture
---|---|---|---
Size (in.)| Shape| Dimensions (in.)| Size (in.)|

4| Round| 12.60 x 7.64 x 3.54| 4.20-5.50| LRXR4xxxxxxx
6| Round| 12.60 x 7.64 x 3.54| 5.91-6.50| LRXR6xxxxxxx
8| Round| 15.55 x 11.34 x 3.54| 7.68-8.27| LRXR8xxxxxxx
4| Square| 12.60 x 7.64 x 3.54| 4.20-5.50| LRXS4xxxxxxx
6| Square| 13.35 x 11.34 x 3.54| 5.95-7.50| LRXS6xxxxxxx
8| Square| 13.35 x 11.34 x 3.54| 7.95-9.50| LRXS8xxxxxxx

Lumens Setting Switch

NOTE: For 1000/650lm and 4000/3000lm, default output lumen is 1000lm and 4000lm respectively. Push switch up or left to activate 650lm and 3000lm respectively.

Attach the test switch to the LRXEMBB fixture or junction box. If the fixture is 6” or 8”, first remove the nut from the end of test switch, and put test switch through the hole of fixture, then thread nut to test switch. If the fixture is 4”, mount to the junction box and provided flexible conduit for remote mounting of the test switch.
NOTE: For phase cut dimming product, dimming leads (violet and gray wires) are open.
Connect the quick connectors in same color of LRX EMBB fixture and LRXEMBBKIT07(or LRXEMBBKIT07HE, or LRXEMBBKIT10) and close quick connector box well.
NOTE: For phase cut dimming product, dimming leads (violet and gray wires) are disconnected. Dimming compatibility for both 0-10V and phase cut, please refer to website: Gecurrent.com/dimming.
Load springs into upright position by twisting the springs upward and carefully insert the fixture to the hole of the frame. Ensure fixture is secure.
- All kit and frame will be completely attached to ceiling.

CAUTION
RISK OF PERSONAL INJURY – Operators shall ensure no appendages are in the path of the torsion springs as they are a pinch hazard when released. The springs will release when the arm is flexed downward. Be cautious that no body part is in the path of the spring when released.

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-005 (A) / NMB-005 (A).

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

www.gecurrent.com
© 2021 Current Lighting Solutions, LLC. All rights reserved. GE and the GE monogram are trademarks of the General Electric Company and are used under license. Information provided is subject to change without notice. All values are design or typical values when measured under laboratory conditions. IND502 (Rev 04/02/21) A-1003897

Logo