Veeape Y06 Multifunctional Electric Pump Instruction Manual

Veeape Y06 Multifunctional Electric Pump

Instruction Manual

Multifunctional Electric Pum
Thank you for purchasing our product. Please read the instruction manual carefully before using the pump, and save it for future reference.

Power Supply/Power Bank Module

High Pressure Air Pum Module

Air Duster Blower/Air Inflation or Deflation Pump Module

Packing List

Attention

1. Do not leave away from the product.
2. Keep away from combustible and explosives.
3. Avoid moisture, sand and prevent from falling.
4.  Do not store the product in a place that is too cold or hot.
5. Do not make the inflator near the fire or discard it casually since it equipped with lithium battery.
6. Keep it away from children.

Specification

Inflation/deflation/

dust-blowing module weight

| ****

180g

Pressure range| 2~160PSI / 0.1-11.0BAR
Inflation speed| 200~300L/MIN
Working temperature| – 10-45 °
Battery capacity| 27.72Wh
Charging input| 5V = 2A / 9V = 1.5A
USB output| 5V = 1.5A

Packing list

1 x Power Supply /Power Bank Module

1 x High Pressure Air Pump Module
1 x Air Dust Blower/ Air Inflation or Deflation Pump Module
1 x Type – C cable
1 x Inflatio n hose
1 x Dust Blowing Tube
1 x Air inflation nozzle (small, medium, large )
1 x Presta valve adapter
1 x Ball Pin

Instruction of Power Supply/Power Bank Module

1. USB Output
   Short press the ON/OFF button to turn on the USB output, which can be used to power devices such as mobile phones.

2. Battery indicator

   • 4 bars of battery and are constant on: 1 00%
   • 3 bars of battery and are constant on: 60%
   • 2 bars of battery and are constant on: 30%
   • 1 bar of battery left and flashes continuously: 5% (Battery is low and need to be charged.)

3. Charging

   • Use a power adapter with an output greater than 5V/2A for Type-C charging. Use a Type-C cable to connect the power supply with the charger adapter(not included) to charge.
   • When the indicator bar is flashing: charging When the indicator bar is fully on: fully charged Tips:
   • The pump or air dust blower cannot be used during charging.ng pump cannot be used during charging.

Instruction of Hih Pressure Air Pump Module

Installation Steps

1. Step 1: Connect the air pump module with the power supply module, slide up the External lock power button to lock the connector to turn on the air pump.
   

2. Step 2: Align the hose with the notch, turn clockwise to lock the hose.

3. Step 3: Select modes and units, preset the pressure and connect it to the tire to start working.

4. Step 4: Power off, and disassemble power supply.

0n and OFF

• Power on Power off Power on: Connect the peripheral connector, slide up to lock the connector, and automatically turn on when the power is turned on.
• Power off: Slide the lock button down to automatically power off.
• In the power-on state, if there is no operation within 3 minutes, it will automatically shut down.

Connect Hose to Valve
Schrader valve
Mountain cycliing, electrical bike, motorbike, and car, are equipped with schrader valve. Inflation: Connect tire valve with the connector of the hose(Schrader valve) to start inlation.
Road cycling and few mountain cycling may use presta valve adapter.
Inflation:
Presta valve

1. Connect presta valve adapter to the hose (Schrader valve).
2. Unscrew the tire valve screw, and connect them to start inflation.

Ball pin

Inflation: Connect the ball pin to the hose (Schrader valve) tightly, then insert it into the hole of the ball to inflate.

Power Button
Short press the start button to turn it on to inflate.
Short press the start button to turn it off.

Measure air pressure
After turning on the pump, connect the high-pressure air hose with the measured subject, the display shows the current air pressure value.

Ch eck the Inflation Pressure Value
In order to ensure safety, before charging, please check the required inflation pressure of the items by reading the instruction manual or other means, to avoid personal injury caused by overcharging.
Tires
The air pressure range of motorcycle and bicycle tires is marked on the side of the tire.
The inflation pressure is related to the load weight. For more detailed air pressure recommendations, please refer to the manual of the relevant vehicle.
Balls
The air pressure range of balls such as football, basketballs, and volleyballs is marked around the ball inflation holes. For more detailed air pressure recommendations, please refer to the manual of the relevant balls.

Mode Selection
When you short press you can choose different charging scene modes, namely:

Modes

| Suggested Pressure Range| Adjustable Pressure Range
---|---|---
Car| 2.4BAR| 0.1- 4.4BAR
Moto r| 2.7BAR| 0.1-3.7PSI
Bike| 38PSI| 2-150PSI
Cus tom| 100PSI| 2-160PSI
Ball| 8PSI| 2-15PSI

Unit switching
Press and hold to switch the air pressure display unit Unit conversion formula: 1 BAR = 14.5PSI

Preset air pressure value

• Short press0 Adjust the preset air pressure value +/-O.5PSI. Long press 0 0 : You can quickly adjust the preset air pressure value.

Note:

• The pump can automatically preset the air pressure value according to the scene you choose.
• The pump has a memory function — when you turn it on, the scene will be same as that you chose last time.

LED Light
Long press to turn on the LED light, long press to turn off the LED light.

Pressure Calibration
After turning on the pump, if the measured pressure value is not zero, press the button for 3 seconds (without connecting the charging object) at the same time, the air pressure value will be automatically calibrated to zero and the light will on.

Note:
This product has been reset at the factory. Due to altitude or sensor differences, when the current pressure value is not zero, manual calibration can improve the accuracy of measured air pressure. Calibration is not recommended at high temperature.

Hih Tern erature Safet Precautions

After the inflation is completed, there would be heat caused by a long-running at the joint of the air hose and the interface of pump. Do not touch it directly with your hands.

Instruction of inflation/Deflation/Dust-blowin Part

Top Part

Installation: Connect the dust blowing to the mobile power supply, slide the lock connector upward, and it will automatically turn on when the power is turned on.
Power off: Slide the lock button down to automatically power off. In the power-on state, if there is no operation within 3 minutes, it will automatically shut down.

inflation/Deflation/Dust-blowing

• Blowing dust:Connect the air hose to the air pump connector to blow dust.
• lnflation:Connect the nozzle to the air pump connector to inflate.
• Deflation:Connect the air nozzle to the air pump connector to release the air.

Dust-blowing Hose Installation

Dust blowing: Install the dust blowing hose on the top of product, which can blow dust and clean the personal desktop, computer case, keyboard and other items.

lnflation Valve Installation

Valve installation

• Choose a suitable valve when inflating,
• connect to the side outlet (a).
• Choose a suitable valve when deflating,
• connect to top inlet (b).

Small Valve

• When inflating, choose a small valve and install it to the outlet on the side.
• When deflating, choose a small valve and install it to the top inlet.
• Suitable for recharging or pumping products sue as swimming rings, yoga balls, etc.
• Note: When the swimming ring is filled with a small valve, to quickly inflate, the valve of the ring needs to be opened by the tip of small valve.

Medium Valve

• When inflating, choose a medium nozzle and install it to the outlet on the side.
• When deflating, choose a medium nozzle and install it to the top inlet.
• Suitable for inflatable pads, inflatable sofas, inflatable beds, storage bags, etc.

Large Valve

When inflating, choose a small valve and install it to the outlet on the side.
When deflating, choose a small valve and install it to the top inlet.

Deflation Valve Installation

Deflation :
Install the deflation valve and the medium valve at the rear of the product, which can be used for vacuum storage bags.

Power Button

After long pressing the power button, the motor starts up, and the battery indicator lights up.
Release the power button to shut down.

Air Pressure Value of Common Products

Troubleshooting Guide

1. Check whether the battery is fully charged.
2. Check the air pipe for leaks.
3. Check whether the connection parts at both ends of the air pipe are tightened.
4. Check whether the inflated items are leaking.

Can’t inflate on boot|

1. Check whether the battery is fully charged.
2. Check whether the current tire pressure is higher than the preset value.

The preset pressure cannot be adjusted.| Check if you choose the incorrect mode, select the Custom Mode to adjust the preset value in the range of 2-160PSI.
Can inf late but the air pressure display does not change|

1. Low-pressure products such as balloons are not within the measurable range of the device.
2.  In the case of an empty tire, the tire pressure value can be displayed after a short period of inflation.

The inflator automatically shut down after connecting hose| The pump will shut down automatically after 3 minutes with no operation, long press the start button to restart.
There is leakage when connecting the hose| Tighten the hose
The color of the power indicators in charging state is different from that in standby state.| The power lithium battery has a significant voltage drop during the discharge process, which causes the color of the indicator light in the charging state and the standby state to be inconsistent. This phenomenon is not a malfunction.
The power indicator does not light up after charging| **** Replace with a safe and compliant charging cable and adapter to recharge.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>