HDX 31424PS 3 Shelf Storage Unit User Manual
- May 15, 2024
- HDX
Table of Contents
HDX 31424PS 3 Shelf Storage Unit
Note
Please dispose of loose, round plastic pieces. These are used to separate the shelves for shipping purposes.
Caution Warnings
- Two adults are recommended for ease of assembly. Use care when handling.
- Do not allow children to climb or play in or around the shelves.
- Assembly recommended on a soft surface, such as carpet, to avoid scratching flooring finish.
- Each shelf holds up to 250 lbs. evenly distributed.
Specifications
Product weight
|
10.63 lbs.
---|---
Product width
|
23.2 in.
Product depth
|
13.3 in.
Product height
|
30.3 in.
Helpful Hints
- Carefully read all instructions, note and caution warnings before beginning assembly.
- Determine shelving heights prior to assembly to avoid dismantling for adjustment.
- When placing the plastic tapered sleeves onto the posts (step 2-ii), slide tapered sleeves up or down on the post until you feel it “snap” into the lines or grooves of the post.
Accessory Parts List & Quick Guide
A. (24) plastic tapered sleeves (2) replacements
B. (8) posts (with 4 threaded post jointers pre-installed in posts, 4
foot levelers pre- installed in bottom of posts)
C. (3) shelves
Assembly
Step 1: Post Assembly
i. The top post section has a plastic endcap on one end and the bottom post
has a foot leveler attached. Threaded post jointers are pre-installed for your
convenience. Screw the posts (1 long & short) tightly together. **(See Diagram
1)**
Step 2: Bottom Shelf Assembly
i. Locate the desired position of the bottom shelf.
ii. Insert four plastic tapered sleeves into the appropriate post groove,
one in each post. Ensure tapered end is up. See arrow on lock. **(See Diagram
2)**
iii. Place shelf on its side and slide each post with tapered sleeves
through the bottom of the shelf until snug. (See Diagram #3)
iv. After all posts are in place, position the unit in the upright
position.
v. Push down on each corner of the shelf, ensuring that the shelf is in
the fully locked position.
Step 3: Additional Shelves Assembly (See Diagram #4)
i. Locate the desired position of the next lowest shelf and insert the
tapered sleeves into the posts.
ii. Slide the shelf down from the top of the posts and onto the tapered
sleeves. Push down on each shelf corner, ensuring that the shelf is in the
fully locked position.
iii. Repeat for the remaining shelves.
Step 4: Adjust the foot levelers in or out at the bottom of the posts to
attain proper leveling. (See Diagram #5)
NOTE: The tapered sleeves must be at the same height for each pole to
ensure the shelf sits on the sleeves levelly.
NOTE: The post has a groove with a double line marking. It can help to
identity the height of the tapered sleeve in each post.
HARDWARE CONTENTS
-
Washer Qty. 2
-
Plastic Anchor Qty. 2
-
Screw Qty. 2
To prevent the unit from tipping over, secure it to a wall in the following
manner: Drill a hole in the wall using a 1/4 in. drill bit (not included).
Insert the plastic anchor (BB) into the hole. Insert the screw (CC) through
the washer (AA) then through the back of the top shelf wire and into the
plastic anchor (BB) as shown. Be sure unit is secure and doesn’t wobble or tip
over.
- Unit must be placed on a level surface or leveled with included hardware (when applicable).
- Do not sit or stand on or allow children to climb, sit or stand on the assembled product.
- For safety reasons, it is imperative that this unit be mounted on the wall or floor.
- Unit can tip over causing severe injury or death.
- Do not exceed the recommended weight limits.
- Evenly distribute the weight on each level and always keep the heavier loads on the bottom.
- Before cutting, drilling or hammering into any wall or floor surface, verify the location of electrical, plumbing and gas lines. Cutting may cause serious injury.
CUSTOMER SUPPORT
Questions, problems, missing parts?
Before returning to the store call Customer Service
8 a.m. – 6 p.m., EST, Monday-Thursday 8 a.m. – 5 p.m., EST, Friday
888-449-5520
WWW.HOMEDEPOT.COM
Retain this manual for future use.
