amate audio S6P 6 Inch Two Way Passive Speaker User Manual

May 15, 2024
amate audio

amate-audio-LOGO

amate audio S6P 6 Inch Two Way Passive Speaker

Safety Instructions

  1. All safety instructions must be read before using this device.
  2. Keep and follow these instructions
  3. Heed all warnings
  4. The exclamation mark in the triangle indicates internal components which if replaced can affect safety.
  5. The lightning symbol within the triangle indicates the presence of dangerous uninsulated voltages.
  6. Only clean the device with a dry cloth.
  7. Do not block any ventilation openings. Install by the manufacturer’s instructions.
  8. Do not install the device near heat sources such as radiators, heaters or other heat-emitting elements.
  9. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus
  10. The equipment must be repaired by qualified technical service personnel when:
    • The mains supply cable is damaged, or
    • Any object or liquid has damaged the device; or
    • The equipment does not function normally or correctly; or
    • The equipment has been exposed to rain; or
    • The chassis is damaged
  11. Disconnect the device in the case of electric storms or during long periods of disuse.
  12. WARNING – To reduce the risk of fire or electric shock, do not expose this device to rain or moisture
  13. The equipment shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the device.
  14. For hanging and installation, use manufacturer-recommended accessories only.

INTRODUCTION

General
Amate Audio would like to thank you for your confidence in our NITID Series. We suggest you to carefully read the following instructions in order to obtain the best results in performance.

Features and presentation

S6P

  • Passive acoustic system
  • NL4MP Speakon input & parallel output
  • 200 W program power
  • Sensitivity 1 W / 1 m: 92 dB
  • 1 x 6″ neodymium magnet woofer with 1.5” voice coil and fibre cone
  • 1″ phenolic diaphragm neodymium magnet tweeter
  • 8Ω and 16Ω available

CONNECTIONS

Connection description
A) SPEAKON: The S6P uses two NL4MP Speakon terminals and is duly prepared for a perfect connection in a parallel system. Terminal Pins +1/-1 must be always used, disregarding the +2/-2 which are not internally connected. Respect always the polarity +/-.

Fig. 1. NITID passive connectors

  • It is strongly recommended to use a two-conductor high-quality wire, non-shielded and two-coloured. We recommend using a minimum section of 4 mm2 for each conductor. Avoid long wire distances as they induce to important power and quality losses.
Configurations

Full-range stereo configuration
Connect each output of the amplifier LEFT/RIGHT to each cabinet using two independent wires.

Fig. 2. Full-range stereo configuration

Full-Range parallel stereo configuration
Connect the amplifier’s output to the Speakon’s input of the first cabinet, always respecting the polarity positive +1, negative -1. Then, make a bridge from the first cabinet to the second one.amate-audio-S6P-6-Inch-Two-Way-
Passive-Speaker-FIG-3

Full-range parallel stereo configuration

Passive configuration with subwoofer

There will be times when you will be interested in reinforcing your NITID Systems with subwoofer units, in passive mode. In this case only one amplifier will be used for the whole system. Connect one of the outputs of the amplifier to the subwoofer through a wire. Then, make a bridge from the link Speakon connector of the subwoofer to its respective mid-high top unit, always respecting the correct polarity between both systems. Do the same with the other channel. It is also correct, if the installation requires so, to make the connection in the opposite way, that is, from the amplifier to the top cabinet and then to the subwoofer.amate-audio-S6P-6-Inch-Two-Way-Passive-
Speaker-FIG-4

Bi-amplified configuration with subwoofer
A wire with the maximum available section (4mm2 minimum) should link the low frequencies output channel of the amplifier to one of the subwoofers. Two subwoofers can be also connected by bridge one to another, as long as the polarity is strictly respected. Connect the other output of the amplifier to the Full-Range cabinets. It is also possible to use only one amplifier for the low reinforcement, connecting each one of the subwoofers to the two outputs of the amplifier and consequently, connecting the Full Range cabinets to a second amplifier.amate-audio-S6P-6-Inch-Two-Way-Passive-Speaker-
FIG-5

Fig. 5. Bi-amplified with subwoofer configuration (option 1)

amate-audio-S6P-6-Inch-Two-Way-Passive-Speaker-FIG-6

Fig. 6. Bi-amplified with subwoofer configuration (option 2)
In order to allow a bridge connection between cabinets, each one of them has been provided with two Speakon connectors that allow the Input / Output function indistinctly. Terminal Pins +1/-1 must be always used, disregarding the +2/-2 which are not internally connected.

MOUNTING AND PLACEMENT

For a proper installation of the acoustic cabinet systems, it is strongly recommended to carefully read the following advice.

Placement

When possible, cabinets should be located in a high position, slightly inclined to the audience. If the loudspeakers are located too low, the listeners at the end of the room will not hear a good sound quality.

Fig. 7. Flying placement

Use with subwoofer or tripod

The S6P is equipped with a 35 mm socket for mounting the speaker on a subwoofer or tripod. Be careful not to use this system on non-flat surfaces as it may become unstable.amate-audio-S6P-6-Inch-Two-Way-Passive-Speaker-
FIG-8

Fig. 8. Use with subwoofer and tripod

Rotatable logo
All grille’s logo can be rotated.

Flying
Only experienced people should fly speaker cabinets. Extreme care should be taken to ensure the load-bearing capabilities of the structures where the cabinets will be placed. Hanging hardware (as chains, eyebolts, lock pins…) should be regularly inspected and replaced if in doubt.

Vertical flying with HR bar
For the S6P, use HR-S or HR-S/GT flying bar for vertical flying. Refer to “HR-S instructions manual” and “HR-S/GT instructions manual” for more information.amate-audio-S6P-6-Inch-Two-Way-Passive-Speaker-
FIG-9

Fig. 9. HR-S and HR-S/GT flying bar for S6P

Vertical flying with SP-6N
For the S6P, use the SP-6N bracket. Refer to the “SP-6N instructions manual” for more information.

Fig. 10. SP-6N bracket for S6P

Vertical flying with SP-WHR
The SP-WHR is an optional accessory for mounting on wall (vertical orientation) one unit of S6P. Refer to the “SP-WHR instructions manual” for more information.

NITID GRILLE
To remove the front grille, first remove the screws on both the left and right side. Insert two bent paper clips into the holes in the grille and carefully pull it off.amate-audio-S6P-6-Inch-Two-Way-Passive-Speaker-
FIG-12

Fig. 11. Grille screws

TECHNICAL FEATURES

Note: Specifications are subjected to change without prior notice.

The NITID loudspeaker systems have been designed, engineered, and manufactured in Barcelona – SPAIN by Amate Audio S.L. Perpinyà, 25 · Polígon Industrial Nord · 08226 Terrassa T. +34 93 735 65 65 – F. +34 93 735 60 48 – info@amateaudio.com

R &D and FACTORY
Violinista Vellsolà, 18 · 08222 Terrassa T. +34 93 736 23 90 – F. +34 93 786 47 00

Barcelona – SPAIN

Specifications

  • Product: NITID S6P
  • Program Power : 200 W
  • Sensitivity : 92 dB (1 W / 1 m)
  • Components:
    • 1 x 6″ neodymium magnet woofer with 1.5″ voice coil and fiber cone
    • 1 phenolic diaphragm neodymium magnet tweeter
  • Available Impedance: 8 ohms and 16 ohms

Frequently Asked Questions (FAQ)

  S6P

Impedance
Nominal| 8 Ω or 16 Ω
Power
R.m.s| 100 W
Program| 200 W
Connectors| 1 x Speakon NL4MP input 1 x Speakon NL4MP link
Audio Performance
Frequency response

(-10 dB usable bandwidth)

| 64 Hz – 20k Hz
SPL (1W / 1m)| 92 dB
Nominal directivity (-6dB)| 70º x 70º
Components
LF| 1 x 6” neodymium woofer (1.5” voice coil) with carbon fibre cone
HF| 1 x 1” phenolic diaphragm neodymium tweeter
Cabinet
Type| Bass-reflex
Height| 370 mm
Width| 220 mm
Depth| 226 mm
Weight (net)| 5.4 Kg
Material| Multilayer birch plywood
Finish| Hi-resistance black matt Polyurea coating.

1.5 mm steel front grille with black acoustic mesh

Q: What should I do if the device does not function normally?
A: If the equipment does not function correctly, seek qualified technical service for repairs.

Q: Can I use any type of wire for connections?
A: It is recommended to use a two-conductor high-quality wire with a minimum section of 4 mm2 for each conductor.

EXPORT & CUSTOMER SERVICE

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals