GoldenEar T66 Built In High Powered Super Subwoofer User Guide
- May 15, 2024
- GoldenEar
Table of Contents
- T66 Built In High Powered Super Subwoofer
- Technical Specifi cations
- Unpacking – Please Follow These Steps to Safely Unpack Your Speakers
- Positioning – Check the User Manual for Detailed Instructions
- Connections – Check the User Manual for Detailed Instructions
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
T66
Loudspeaker System With Built-In
High-Powered SuperSubwoofer
Quick Start Guide
T66 Built In High Powered Super Subwoofer
The crossed-out wheeled bin is the European Union symbol for indicating separate collection for electrical and electronic equipment. This product contains electrical and electronic equipment which should be reused, recycled or recovered and should not be disposed of with unsorted regular waste. Please return the unit or contact the authorised dealer from whom you purchased this product for more information.
| Read All Instructions
---|---
| Avoid Direct Sunlight
| Avoid Extreme Temperatures
| Avoid Solvents
| Avoid Moisture
| Secure Cables
Technical Specifi cations
T66
Driver Compliment| One High-Gauss Reference High-Velocity Folded Ribbon AMT
Tweeter Two 4.5” High-Definition Cast-Basket Mid/Bass Drivers
Two 5” x 9” Long-Throw Quadratic Subwoofers
Two 8” x 12” Quadratic Planar Back-Wave-Driven Radiators
Passive Radiator Surface Area| 53.36in2 (344.3cm2)
Efficiency| 91dB 1W/1M @ 4Ω (2.83V/1M)
Frequency Response:| 29Hz–25kHz typical (-6dB on axis @ 29Hz, anechoic bass
response)
Nominal Impedance| 4Ω
Recommended Amplification| 20 – 500 watt/channel
Built-In Subwoofer Power Amplification| 1000W peak/500W RMS, DSP-Controlled
Speaker Dimensions| 7 1⁄2″ (19.1 cm) W x 14 3⁄4″ (37.6 cm) D x 48 7⁄8″ (124.1
cm) H (height is with base and feet installed, no spikes)
Base| 11 13⁄16″ (30 cm) W x 17″ (43.2 cm) D
Weight| 60 lbs (27.2 kg)
Power Requirements/ Consumption:| Low Voltage Version — 120 V at 50 or 60 Hz /
1200 Watts High Voltage Version — 240 V at 50 or 60 Hz / 1200 Watts (Approved
for NA (TUV) and the CE market.)
Specifi cations Subject to Change Without Notice
Unpacking – Please Follow These Steps to Safely Unpack Your Speakers
T66 speakers are heavy, we recommend 2 people to unpack them
- Remove any wrapping and lay box fl at as shown
- Carefully cut tape
- Stand box up as shown with top piece on top
- Slide the packing out of the box, and remove the top piece to reveal the base of the speaker
- Carefully turn the speaker over and place base on floor
- Carefully remove the packing shell and the protective bag
Positioning – Check the User Manual for Detailed Instructions
Positioning T66 as left/right fronts
Positioning T66 as surrounds
Connections – Check the User Manual for Detailed Instructions
Connecting Speaker Cables
- Using full-range speaker cables
- Using bi-wire speaker cables, jumpers must be removed
A Connect AC power cable Set Subwoofer Level to 12 o’clock (straight up) to start, see user manual for more information
Connecting the LFE Input
Using the LFE Input is always in addition to connecting speaker cables, it is
never a replacement for connecting speaker cables
For receivers or processors with only one LFE output, use a “Y” Connector
****This product complies with the essential
requirements of the EMC directive 89/336/EEC
For Additional Help With Installation Visit:
www.goldenear.com
T66 Quick Start Draft 06_06_23.indd 4
6/6/23 3:38 PM