Ergomaker SM205-120 Electric Height Adjustable Standing Desk User Guide

Ergomaker SM205-120 Electric Height Adjustable Standing Desk

USER MANUAL

If you have any questions, please contact us:
service@ergomaker.com

CAUTION

FAILURE TO COMPLY WITH OR OBSERVE ALL ASSEMBLY, SAFETY AND OPERATION INSTRUCTIONS AND WARNINGS REGARDING THE USE OFTHIS PRODUCT MAY RESULT IN SERIOUS PROPERTY DAMAGE OR BODILY INJURY.

IMPORTANT:

Any user or installer of desk must study this manual carefully.
If this desk is sold, please provide the manual to the buyer.

SAFETY AND WARNINGS

• Inappropriate use of this product may cause property or bodily injury.
• Check surroundings on all sides before using the desk. Body parts and property can be crushed if trapped between an immobile obstacle and the desk’s range of motion.
• Ensure the length of power cords are accounted for when operating the desk. Monitors, computers, speakers, anything with a cord that is not long enough for the desk’s range of motion could be pulled down or have its wires broken. Items pulled off the desk may cause other items to fall.
• Please provide this operation to any users, installers, or support personnel operating the product.
• Do not open any of the components: lifting columns, power adaptor, or handset. There is a danger of electric shock.

USAGE

• This height adjustable desk has an electric motor and is designed for use in dry work areas only.
• The desk height is adjustable so that it can be positioned at the most ergonomically suitable height.
• These desks are designed only for the purposes included in this manual. They should not be used in environments with high humidity or dampness. Any other use is at user’s risk.
• Do not move around, crawl or lie under the desk frame. Do not sit or stand on the desk frame.
• Children should never use the desk unless they are supervised by adults.

Liability: Under no circumstances does the manufacturer accept warranty claims or liability claims for damages caused from improper use or handling of the desk frame other than that which is des-cribed in this operation manual.

SETUP AND INSTALLATION

• Choose a placement for the desk that’s a safe distance from window frames, radiators, furniture etc. so that people do not get stuck or trapped by the desk.
• Do not place any objects that are taller than 50cm (20’’) underneath the desk.
• After it has been assembled, when moving the desk, DO NOT lift the desk by the desktop. Lifting this way can stress the fasteners connecting the desk base to the desktop. Lower the desk completely and lift the desk by grabbing the top of the desk base or by removing the desktop first.

PART LIST

Step 1:

Lay out all components and hardware to ensure that you have all the parts listed on the components list. Use a padded or carpeted area for assembly to avoid damage. For ease and safety, we recom-mend two people for assembly.

Step 2:
Place Leg (Part 1) and Motor Leg (Part 2) as shown. Line up the holes on Crossbar (Part 6) with the holes on Leg and Motor Leg. (PAY ATTENTION TO THE ORIENTATION OF THE CROSSBAR). Insert qty 4 screws (Hardware A). Using the Allen Wrench (Hardware G M5) to tighten 4 screws.

Step 3:

Place the frame upside down as shown. Attach each Foot (Part 3) with qty 4 machine screws (Hardware C) and tighten them in a cross pattern.

Step 4:

Line up the holes on Side Brackets (Part 4) with the Leg/Motor Leg. Insert qty 4 flat head screws (Hardware B). Use the Allen Wrench (Hardware G M5) to tighten screws.

Step 5:

Use the Wrench (Hardware H) to loosen the 2 Hex nuts on Drive Rod (Part 5) UNTIL THE HEX NUTS ARE SEPARATED.

Step 6:

Insert the left Drive Rod (Part 5) into the Leg (Part 1) UNTIL THE PROTRUSION IS STUCK.

Make sure the protrusion is stuck. Otherwise, the left side of the desk will not go Up/Down when you adjust the height.

Step 7:

Put the right Hex nut on Motor Leg (Part 2) UNTIL THE HEX NUT IS STUCK BY THE CLIP.
Then slide the sleeve of Drive Rod (Part 5) to connect the Motor Leg (Part 2) UNTIL THE SLEEVE IS STUCK BY THE RIGHT HEX NUT.

Make sure the Hex nut and Sleeve are stuck by the Clip. Otherwise, the left side of the desk will not go Up/Down when you adjust the height.

Step 8:

Use the Wrench (Hardware H) to tighten the 2 Hex nuts on the Drive Rod.

Tighten the 2 Hex nuts on the Drive Rod. Otherwise, the left side of the desk will not go Up/Down when you adjust the height.

Step 9:

Place Desktop (Part 7) upside down on a debris-free carpeted area or a blanket.
The Desktop has pre-drilled holes and threaded inserts, they should be visible and facing up.
Connect Desktop with qty 4 wood dowels (hardware F).

Line up the holes on the Connecting Plates (Part 9) with the holes on the desktop, insert qty 6 screws (Hardware E). Use the Allen Wrench (Hardware G M4) to tighten screws.

Step 10:

When placing the frame on Desktop (Part 7 ), lift it up. DO NOT SLIDE IT. This will help protect Desktop.
Line up the holes on the Side Bracket (Part 4) with the threaded inserts on Desktop. Insert qty 8 screws (Hardware D). Using the Allen Wrench (Hard-ware G M5), rotate screws but DO NOT TIGHTEN THEM. After all 8 screws are started, go back and tighten them all the way. Be careful to not over-tighten, to avoid stripping.

If you are having troubles getting all the screws started, it is because other screws are too tight. You will need to back out some screws in order to loosen the tolerance of the screw holes.

Step 11:

Line up Handset (Part 10) with the holes near the Motor Leg (Part 2) and attach it to De sktop with qty 2 screws (Hardware D). Be careful to not over- tighten, to avoid stripping.

Step 12

Plug the motor cable into the 6-pin port on Handset (Part 10). Connect the Handset cable and Power Cord (Part 11).

Step 13

Use the adhesive-backed Cable Clips (Hardware I) to organize your wires, keep a clean presentation, and prevent any wires from snagging on anything when adjusting height.

Step 14:

Turn the desk right side up. Be careful of the wires and Handset. Attach Hooks (Part 8) to Side Brackets (Part 4) as shown.

Step 15:

Adjust the leveling studs on Foot (Part 3) as needed to make the desk level. Plug the Power Adaptor (Part 11) into a 110V-220V outlet.

Step 16:

IMPORTANT! You must Reset the desk prior to use:

Press and hold the “ ” button on the Handset until the desk reaches its lowest height. Release the ” ” button.
Press and hold the ” ” button again for more than 3 seconds until ” ” is disp ayed. Release the “ ” button.

Press and hold the “ ” button until the desk lowers a little bit more, slightly rises and stops. Release the ” ” button.
The handset will then display the current height.
Your desk is now ready to use.

IF THE LEFT SIDE DOESN’T GO UP/DOWN WHEN USING THE DESK, GO BACK TO STEP 5, 6, 7 and 8. MAKE SURE THE DRIVE ROD IS INSTALLED CORRECTLY.

TECHNICAL SPECIFICATIONS

Soft Start/Stop
Adjustable leveling studs

PROGRAMMING INSTRUCTIONS

MEMORY SETTINGS

Save up to two commonly used desk heights and recall them quickly.

1. Use the “ ” or “ ” button to move the desk to the desired height.
2. Press and hold the ” or  ” button for more than 3 seconds until the LED reads ” S-1 ” or ” S-2″. Then the current height is assigned to a number on the handset.
3. To bring the desk back to any of these assigned heights, short press the numbered button.

HANDSET LOCK

The Handset can be locked to prevent accidental activation or movement of the desk and toprevent desk settings from being accidentally changed by children or coworkers.

TO LOCK: Press and hold the “ ” and “ “buttons simultaneously for 5 seconds until the LED reads “Loc”.
TO UNLOCK: Press and hold the “ ” and “ “buttons simultaneously for 5 seconds until the LED switches from “Loc” to the height display.

TROUBLESHOOTING

If your desk does not respond when you try to raise it or lower it, or if the handset displays error messages, perform the reset procedure below.

RESET PROCEDURE

1. Unplug the power cord. Reconnect all the cables and make sure all the cables are secure (Motor Leg to Handset, Handset to Power Adaptor).

2. Plug the power cord back in.

3. Press and hold the ” ” button until the desk reaches its lowset height. Release the ”   ” button.

4. Press and hold the ” ” button again for more than 3 seconds until ” rst ” is displayed. Release the ” ” button.

5. Press and hold the ” ” until the desk lowers a little bit more, slightly rises and stops.

6. The handset will then display the current height, and you should be able to op erate the desk.

7. You may also need to do this if the desk is ever unplugged or l oses power.

ERROR CODE TABLE

button until the desk lowers a little bit more, slightly rises and stops.
| Er1| Motor Disconnection| Perform reset procedur

Contact us: service@ergomaker.com

If you have any questions, please contact us via e-mail:

service@ergomaker.com

www.ergomaker.com

Product Specifications:

Model: SM205-120

Components Included:

• Qty 2 Foot
• Qty 1 Leg
• Qty 1 Motor Leg
• Qty 1 Crossbar
• Qty 3 Connecting Plate
• Qty 1 Handset
• Qty 2 Side Bracket
• Qty 2 Desktop
• Qty 1 Power Adaptor
• Qty 1 Drive Rod
• Qty 2 Hook

Hardware Included:

• Hardware A: Allen Wrench (M5)
• Hardware B: Flat Head Screws
• Hardware C: Machine Screws (M5)
• Hardware E: Screws (M4)
• Hardware F: Wood Dowels
• Hardware G: Allen Wrench (M4, M5)
• Hardware H: Wrench

Frequently Asked Questions (FAQ):

Q: Do I need any additional tools for assembly?

A: No, all necessary tools are included in the package.

Q: How many people are recommended for assembly?

A: We recommend two people for ease and safety during assembly.

References

• Ergomaker - Premier Manufacturer of Ergonomic Furniture

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>