ZINWELL ATSC 3.0 ZAT-6000 Broadband Set Top Box Installation Guide

ZINWELL ATSC 3.0 ZAT-6000 Broadband Set Top Box

FCC STATEMENT

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with min imum distance 20cm between the radiator & your body.

Important Safety Instruction and Precaution

• Read through all the instructions carefully before use.
• Operate this product only in the manner described.
• Only a Water dampened soft cloth is recommended to clean the surface of this product.
• Do not expose this product to excess vibration.
• Keep this product in well-ventilated areas.
• The following substance or condition will cause the damage to this product:
  • any liquid such as water or moisture
  • extreme heat, cold, humidity
  • dusty or sandy environments
• During lightning storms, disconnect this product from electrical mains and antenna.
• Only place this device on stable surfaces and ensure that any attached cables are secure and will not cause the device to fall.
• There are no user-serviceable parts in this product.
• Any unauthorized attempt to disassemble or repair this product will void the product warranty and may cause a dangerous electric shock.
• Retain the manuals for future reference.
• ONLY remove any power or data cords by pulling them from the plug
• Using this product near other electronic devices may cause interference.
• Images shown in this document are for references only and there may be differences between images and actual products.
• Do not mix old and new batteries in the IR remote control.

Knowing Your Set-Top Box

Theory of Operation

Model Specification

HEVC 4Kp60 (ATSC 3)

Output| HDMI 2.1
Audio (optional)| Decode| AC-3 (ATSC 1)

AC-4 (ATSC 3)

Output| HDMI 2.1
Ethernet| 10/100M| RJ-45
Wi- Fi| 2.4G/5G| 802.11a/b/g/n/ac
Antenna| 1T1R
DC Power Adaptor| DC Jack| 12V / 1.5A
Peripheral| USB 3.0| USB Type A
LED indicator| ON: Green, Standby: Red
Remote Control| IR| 32 Keys
Dimension| 211 x 80 x 36.2 (mm)
HDCP (Optional)| HDCP 1.4, HDCP 2.2,

HDCP 2.3

Widevine| Level 1
HDR (Optional)| HDR-10, HLG, SL-HDR

Features

• Emergency alerting system
• ATSC 3.0 broadcast application compliant
• ATSC 3.0 / 1.0 receiving capability
• 4k UHD Video
• Remote learning Application

Package Contents

• 1 x STB ASTC 3.0 Set Top Box
• 1 x IR Remote Control
• 1 x Power Adaptor (12V/1.5A)
• 1 x Installation and Description Guide (This Document)
• 1 x Window Antenna (Optional for the project)
• 1 x HDMI Cable (Optional for the project)
• 1 x RF Cable (Optional for the project)

Panel Specification

1. Antenna port is to connect the cable from your aerial
2. HDMI out port is to connect the cable from your display
3. LAN port is for Ethernet (RJ45) network or internet access
4. USB port is for peripherals such as thumb drive, storage devices and so on
5. RESET button is to reboot the device manually
6. DC IN is to connect the power adapter (12V/1.5A) to provide power to the Set-Top Box

Finding Out the IR Remote Control

Installing Your Set Top Box

Installing Instruction in 3 Steps

• Step 1. Connect your Coaxial Cable to the A n tenna Port
• Step 2. Insert your HDMI cable from HD TV into HDMI OUT Port
• Step 3Plug the power adaptor into DC IN Port while the other end into power socket

Refer to the image below for the designated port in each step

Setting up the Program System First Time Installation
Note: For watching encrypted channels it is necessary to connect to the internet either via Wi-Fi or Ethernet. Please refer to Sections 6 and 7 for connecting to the internet.)

Step 1.
Turn ON the Power of Gateway Quick Setup page will be shown as the image on the left side. Press OK to confirm.

Step 2.
Process of Channel Scanning will be completed once the percentage bar has r each ed 100%

Step 3.
“Service found” stands for available TV channels during scanning.

Step 4
After completion of Channel Scanning, the progr am will start displaying . Refer to the image on the right side,

(WiFi ON) Connecting to Internet via Your Wi Fi/AP Router

*Before Reading the Instructions

• The Wi-Fi and Ethernet functions CANNOT be executed at the same time . Ensure the Set Top Box is NOT CONNECTED to any Ethernet Cable before ENABLING Wi Fi function in the Set Top Box
• Turn ON the Power of Set Top Box (IF it’s the First Time –> P ress the ” SETTING ” button on the remote controller (Refer to th e Image on the right side)

• (IF Any) Ensure the Ethernet Cable is DISCONNECTED to the Set Top Box
• Select Network & Internet –> Press OK on the remote control to confirm

• Use Cursor Keys (▲▼◄ ►) on the remote control to MOVE to Wi-Fi –> Press OK on the remote control to ENABLE Wi-Fi
• A list of Available 2.4G & 5G Networks will be shown.
• Use Cursor Keys (▲▼◄ ►) on the remote control to MOVE to your preferred Wi Fi/AP Router –> Press OK to confirm. (Refer to the image on the right side)

• When the connection is successful, the status CONNECTED ” will appear. (Refer to the image on the right side)

Checking on Internet Connection Status

• Press Settings –> Select Apps –> Press OK to confirm (Refer to the Image on the left side).

• Use Cursor Keys (▲▼◄ ►) on the remote control and MOVE to See all apps Press OK on the remote control to confirm

• Select Aptoide TV Press OK on the remote control to confirm

• Successfully Connected to Internet Access. The list of APKs will BE SHOWN . Refer to the image on the right side.

• Unsuccessfully Connected to Iinternet Access. NIL APK ” will be shown as the images on the left side.

• IF Internet Conection is still unsuccessful, restart your Gateway will be required. Please RE EX E CUTE the steps from

(Wi Fi OFF) Connecting to Internet via Ethernet Network

*Before Reading the Instructions

• The Wi Fi and Ethernet functions CANNOT be executed at the same time . Ensure the Set Top Box is NOT CONNECTED to any Wi Fi before conne cting to the Ethernet Cable

• Refer to the Section 2.5 Panel Specification for the location of each port or button mentioned below.

• Press the SETTING button on the remote control Select Network & Internet –> Press OK on the remote control to confirm

• Connect your Ethernet (RJ45) cable to the LAN port on your Set Top Box –> The system will automatically update the network connection status . Refer to the image on the right side.

• (Wi Fi OFF) Knowing Hot Spot Function

Sharing Internet Access to your PED (Personal Electronic Devices)

• Hot Spot will ONLY be functioning when Network Access is connected via Ethernet and Wi Fi Mode is OFF
• After connecting to Internet via Ethernet, your Set Top Box now is in AP Access Point ) / Router Mode

Nil Setting Action is required

Connecting Your PED to the Internet Access from Set Top Box

• Enable the Fi function of Your PED –> Search for W i Fi Network:
• ZINWELL _xxxx (last 4 digits is the default serial numbers of your Set Top Box ). Default Password “ (refer to Section 8.2 Hot Spot Sharing Password and Name Setting for more details –> Connect it for the Internet Access
• Hot Spot Sharing Password and Name Setting

*Before Reading the Instructions

• Hot Spot will ONLY be functioning when Network Access is connected via Ethernet and Wi Fi Mode is O FF

• Press the ” SETTING ” button on the remote controller (Refer to the Image on the left side).

• Select Network & I n ternet –> Press OK on the remote control to confirm

• Ensure Wi Fi Mode is OFF before entering the Hot Spot Section

• Use Cursor Keys (▲▼◄ ►) on the remote control to MOVE to HotSpot (Refer to the picture on the Right –> Press OK on the remote control to confirm

• Default Hot Spot Name : AndroidAP_xxxx

• Default Hot Spot Password s: A set of numeric combinations. ( Use Cursor Keys (▲▼◄ ►) on the remote control to MOVE to the HotSpot Password section for viewing) (In order to enhance the Security of your Internet Access, it is recommendable to SET UP your Password) If you wish to change your Hotspot

• Password , use Cursor Keys (▲▼◄ ►) on the remote control to MOVE to HotSpot password and enter your password).

• If you wish to change your Hotspot Name use Cursor Keys (▲▼◄ ►) on the remote control to MOVE to HotSpot Name and enter your preferred name.

Function Overview

Guide to the Setting System

Other Functions

Searching for the Available Channels (Auto Scan)

Searching for the Available Channels (Manual Scan)

Selecting Your Preferred Language for Audio

Turning Off the Caption

Selecting the Parental Rating

• MENU –> Parental Rating ( The Admin PIN MUST be ENTERED before entering the Parental Rating screen (The default password is: 0000) –> Select the Rating Restriction –> P ress BACK to confirm

Time Setting

Setting the Display Duration

Changing the Administrator PIN

Obtaining the Program Content Introduction

• Press Guide on the remote control –> Electronic Program Guide –> Use Cursor Keys ▲▼ ◄ ►) to select the different program blocks for getting the program content introduction.

APK Installation and Software Upgrading via USB Storage Device

Step 1.

• Put the APK in an USB storage device
• Insert the USB storage device into the US B port of the Broadband Set Top Box
• Press SETTING button on the remote control –> Select Apps –> Select See All apps
• The following screen will appear –> Select AppInstaller ” to confirm

Step 2.

• Use the remote control to select O p en –> Press OK to co nfirm.

Step 3.

• Select the USB storage device (such as Kingston USB drive) –> press OK to confirm

• App Installer will list all APKs from the USB storage device

Step 4.
The installation screen is as below. Find the ” INSTALL ” button at the bottom right corner of the screen –> Press OK to install.

Step 5.
Select “DONE” to complete the APK installation process.

Software Upgrading via OTA Service

• Before Reading the Instructions
• Ensure your Set Top Box is CONNECTED to the internet successfully.
• Refer to Section 5.1.2 (Checking on Internet Connection Status P.18) for more details

Step 1.

• Press SETTING button on the remote control –> Select Apps –> Select See All apps
• The following screen will appear –> Select Apps Download ” to confirm

Step 2.

• Use the remote control to select O p en –> Press OK to confirm.

Step 3.

Select available NextGenLiveTvLauncher version –> press OK to confirm.

Step 4.

• The installation screen is as below. Find the “INSTALL” button at the bottom right corner of the screen –> Press OK to install.

Step 5.
Select “DONE” to complete the APK installation process.

Trouble Shooting

has been turned on.
No Picture but Sound OK| Nil or incorrect video cable connections| Ensure cables are connected correctly.
“No Signal” Appear on the Screen| Antenna cable is not connected| Connect the antenna cable and check the connection to the rear of Broadcast Gateway
Picture is breaking up| Signal is weak and unstable| Check the antenna connection
Remote Control is not responding| Batteries are flat| Replace the batteries. * Do not mix old and new batteries in the IR remote control
USB device is not detected| Not powered correctly| Check the power source (if fitted) or reconnect

Contact ing Us
Please kindly reach out us via the Contact Us function in our website: https://www.zinwell.com.tw/us/.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>