GE current RUL-Series Lumination RUL Indoor Lighting Installation Guide
- June 4, 2024
- GE current
Table of Contents
Installation Guide
IND408
Lumination® LED Luminaire
Refit Universal Linear Kit
(RUL-Series)
BEFORE YOU BEGIN
Read these instructions completely and carefully.
**WARNING**
RISK OF ELECTRIC SHOCK
- Turn the power off before inspection, installation, or removal.
- Properly ground electrical enclosure.
- Luminaire wiring and electrical parts may be damaged when drilling for the installation of an LED retrofit kit. Check for enclosed wiring and components.
- LED retrofit kit installation requires knowledge of luminaries’ electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
- Install this kit only in luminaires that have the construction features and dimensions shown in the photographs and/or drawings and where the input rating of the retrofit kit does not exceed the input rating of the luminaire.
- To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or other sharp objects.
- This retrofit kit is accepted as a component of a luminaire where the suitability of the combination shall be determined by authorities having jurisdiction.
RISK OF ELECTRIC SHOCK
- Follow all NEC and local codes.
- Use only Ul-approved wire for input/output connections. Minimum size 18 AWG or 14 AWG for continuous runs.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAN ICES-005 (A) / NMB-005 (A)
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Save These Instructions
Use only in the manner intended by the manufacturer. lf you have any
questions, contact the manufacturer.
Prepare Electrical Wiring
Electrical Requirements
The LED luminaire must be connected to the mains supply according to its
ratings on the product label.
Grounding Instructions
The grounding and bonding of the overall system shall be done in accordance to
the local electric code of the country where the luminaire is installed.
Components Supplied
Prior to installation verify that the kit contains all components below.
Electrical Connections
Luminaire Requirements
The unit covered by this report is intended to retrofit: Listed surface-
mounted fluorescent luminaires, or Type Non-IC or type IC recessed mounted
fluorescent luminaires; with or without diffusers that use, straight 2 or 4-ft
tubular lamp(s).
| Model | Length (mm) | Width (mm) | Height (mm) | Spacing between tubes (mm) |
|---|---|---|---|---|
| RUL248A0wwxxLB | 559 | 140 x N | 50 | 140 |
| RUL4880wwxxLB | 1118 | 140 x N | 50 | 140 |
Installation
- Prepare Existing Fixture For Installation
Prior to installation, disconnect all incoming power to the fixture, and remove all electrical parts and ballast compartment cover leaving only the supply and grounding leads.
Remove existing hardware (reflectors/ballast covers, brackets, lamps). Save ballast cover for reuse.
-
Attach Mounting Clips
• Snap two mounting clips onto each LED lightbar.
• Bring the LED lightbar into the housing and reposition the mounting clips as needed. (For temporary placement of the lightbar, the mounting clips have magnets located on the bottom of each clip).
-
Fasten Lightbars to Housing
Once lightbars are in the desired position permanently secure them to housing by inserting supplied self-tapping screws into the endcaps on each end of the light bar.
-
Attach Driver To Housing
• Place new driver into housing and secure. Ensure the driver is properly grounded using a serrated grounding screw (not supplied).
• Connect the power supply lead connectors to the LED lightbar connectors.
• Replace the ballast cover and affix a field-applied label onto the housing.
-
Close the Lens/Door and Secure the Latches
-
IMPORTANT: Only those open holes indicated in the photographs and/or drawings may be made or altered as a result of kit installation. Do not leave any other open holes in an enclosure of wiring or electrical components.
www.gecurrent.com
© 2021 Current Lighting Solutions, LLC. All rights reserved. GE and the GE
monogram are trademarks of the General Electric Company and are used under
license. Information provided is subject to change without notice. All values
are designed or typical values when measured under laboratory conditions.
IND408 (Rev 04/02/21)
Documents / Resources
| GE
current RUL-Series Lumination RUL Indoor
Lighting
[pdf] Installation Guide
RUL-Series, Lumination RUL Indoor Lighting, RUL Indoor Lighting, Lumination
Indoor Lighting, Indoor Lighting, Lighting
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>