Yuxinwei YXW-WX39 Wireless Charger User Manual
- May 15, 2024
- Yuxinwei
Table of Contents
User Manual
wireless charger
Product Appearance
Product Introduction
Thanks for purchasing the multi-functional wireless charger. The wireless charger adopts high-end fast charge IC, with its luxury and portable design. It can provide 3 compact charging stations, powered from only one outlet. Also, it can support mobile phones/earbuds/Apple Watch. The charger will start automatically when devices are placed on it. It can support any cell phones with QI standard. This charger is space-saving designed, which will make your space clean and tidy. All these can help you integrate your electronic equipment and life very well.
Operation Steps
- Connect the charger to a 9V/3A 12V/2.5A QC3.0 adapter through a Type-C quick charge cable to power on
- Put the phone on the charger
- Put the apple watch on and suck it up to charge (Better loosening of the strap)
- Put the charging case of your earbuds on the charger
Product Specification
Input: 9V/3A 12V/2.5A
Phone Output: 15W/10W/7.5W/SW
Watch Output: 2.5W
Earbuds Output: SW
Input Interface: Type-C port
Size: 16.5cm15.4cm12.5.0cm (Open)
Weight: 240g
Accessories List: Wireless Charger1, Type-C quick charge cable1, User
manual”1
LED Indicator Status
| Power On | Blue light keeps on |
|---|---|
| On Charging | Blue breathing light |
| Full Charge | Blue light keeps on |
| Error | Blue lights flashed |
Attention
- Do not squeeze or collide.
- Please keep the charger away from fire, water and other liquid.
- Do not use near magnetic bank card or IC card to avoid malfunctioning .
- Do not use wireless charger in extremely hot, humid or corrosive Environment .
- If you need to clean the charger, please make sure it is not connected with the power source.
Notice: To ensure charging 3 devices safely and efficiently, you must use 9V/3A or 12V2.5A adapter and quick charge cable! (If you don’t use the appropriate adapter and cable, the charger may not charge phone, or may not charge 3 devices simultaneously, or may even damage the charger).
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Radiation Exposure Statement
This device complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment.
The FCC certification of this device refers to RF exposure testing performed
in typical operating conditions, where a person is no closer than 20
centimeters from the device surface at all times, except for non-repetitive
patterns with transient time intervals in the order of a second. Only in the
stated conditions, the device is shown to fully comply with the FCC RF
Exposure requirements of KDB 447498.