GREE LE60-13 Zone Controller Owner’s Manual

May 15, 2024
Gree

LE60-13 Zone Controller

“`html

Product Specifications

  • Model: Zone Controller System LE60-13/GH
  • Manufacturer: Gree
  • Country of Origin: Australia
  • Warranty: Register at here

Product Usage Instructions

Introduction and Safety

Congratulations on purchasing the Gree Zone Controller. It is
essential to keep the Manual, Warranty Booklet, original purchase
documents, and installation certificates in a safe place. Register
the warranty promptly following the steps outlined in the Warranty
Booklet.

The installer must thoroughly read the Installation Manual
before installing the zone controller. The homeowner/user should
also read the Owner’s Manual before operating the appliance.

To maintain the warranty validity, the appliance must be checked
and serviced regularly by the homeowner/user as per the Maintenance
& Service section and Schedule. This practice will help extend
the lifespan of your appliance.

Important Notices

The Australian Greenhouse Office has issued regulations
regarding the use and disposal of refrigerants in the appliance.
Failure to comply with these regulations may result in
environmental harm and substantial fines.

Only qualified and licensed technicians should perform work on
this appliance where specified; otherwise, the warranty will be
void.

Ensure children or individuals with reduced capabilities are
supervised when using the appliance to prevent accidents. If the
supply cable is damaged, it must be replaced by authorized
personnel to avoid hazards.

Operation

The Zone Controller features various functionalities as
indicated in Fig 1:

No. Name Instructions
1 Name of the current zone – Shows the name of the current zone. The set

temperature
displayed on the home page is the temperature of the current
zone.
– Press to switch to another zone.
2| Decrease| Press to decrease the set temperature of the current zone

Frequently Asked Questions (FAQ)

Q: How often should the appliance be serviced?

A: The appliance should be checked and serviced regularly as per
the Maintenance Schedule provided in the manual. Typically,
servicing every six months is recommended to ensure optimal
performance.

Q: Can I install the appliance myself?

A: It is recommended that only qualified and licensed
technicians perform installation work on this appliance to avoid
voiding the warranty and ensure safe operation.

“`

OWNER’S MANUAL
ZONE CONTROLLER
Zone Controller System LE60-13/GH

CHECKING RECEIVED PRODUCT Upon receiving the appliance, please inspect for damage. Claims for damage should be reported immediately with the transportation company. Check the model number of the appliance and ensure it matches the order. In the event an incorrect appliance or a damaged appliance is delivered, it must be returned to the supplier and must NOT be installed. The manufacturer assumes no responsibility for installation of incorrectly delivered and/or damaged appliances.
REGISTER YOUR PRODUCT FOR WARRANTY https://greeac.co.nz/warranty-claim

CONTENTS
INTRODUCTION AND SAFETY………………………………………………………………………………………………………………………2
OPERATION………………………………………………………………………………………………………………………………………………… 3 ON/OFF……………………………………………………………………………………………………………………………………………….. 4 MODE SETTING…………………………………………………………………………………………………………………………………….4 TEMPERATURE SETTING……………………………………………………………………………………………………………………..5 FAN SETTING………………………………………………………………………………………………………………………………………. 5 MENU STRUCTURE……………………………………………………………………………………………………………………………… 6
FUNCTION …………………………………………………………………………………………………………………………………………………7 FRESH AIR…………………………………………………………………………………………………………………………………………….7 HEALTHY………………………………………………………………………………………………………………………………………………7 QUIET……………………………………………………………………………………………………………………………………………………7 SAVE…………………………………………………………………………………………………………………………………………………….8 I-DEMAND……………………………………………………………………………………………………………………………………………..8 HOLIDAY……………………………………………………………………………………………………………………………………………….8
LOW TEMPERATURE DRY……………………………………………………………………………………………………………………..8 X-FAN……………………………………………………………………………………………………………………………………………………9 FILTER CLEAN REMIND…………………………………………………………………………………………………………………………9 MEMORY………………………………………………………………………………………………………………………………………………9 TEMPERATURE UNIT…………………………………………………………………………………………………………………………….9 RESET WIFI…………………………………………………………………………………………………………………………………………..10 ZONE CONTROL…………………………………………………………………………………………………………………………………………11 DAILY TIMER…………………………………………………………………………………………………………………………………………11 WEEK TIMER……………………………………………………………………………………………………………………………………….. 12
TWO WEEK TIMER………………………………………………………………………………………………………………………………..13 ZONE CONTROL………………………………………………………………………………………………………………………………….. 14 MAIN ZONE SETTING…………………………………………………………………………………………………………………………….15 ALWAYS OPEN ZONE…………………………………………………………………………………………………………………………….15 ZONE PARAMETER SETTINGS………………………………………………………………………………………………………………15 CONNECT RF REMOTE CONTROL…………………………………………………………………………………………………………16 SYSTEM……………………………………………………………………………………………………………………………………………………..17 DATE AND TIME…………………………………………………………………………………………………………………………………….17 HOUR FORMAT SETTING………………………………………………………………………………………………………………………17 LANGUAGE SETTING…………………………………………………………………………………………………………………………….18 LIGHTNESS SETTING…………………………………………………………………………………………………………………………….18 BACKLIGHT SETTING…………………………………………………………………………………………………………………………….19
SOUND SETTING…………………………………………………………………………………………………………………………………..19 MAIN OR SUBSIDIARY CONTROLLER…………………………………………………………………………………………………….20 DEBUG………………………………………………………………………………………………………………………………………………….20 VIEW …………………………………………………………………………………………………………………………………………………………21 PARAMETER VIEW………………………………………………………………………………………………………………………………..21 AMBIENT TEMPERATURE OF ZONE……………………………………………………………………………………………………….21
VIEW MALFUNCTION……………………………………………………………………………………………………………………………..21 WIFI MODULE INSTALLATION………………………………………………………………………………………………………………………..22 ERROR CODES……………………………………………………………………………………………………………………………………………..25 NORMAL OPERATION CODES……………………………………………………………………………………………………………………….26 MAINTENANCE AND SERVICE……………………………………………………………………………………………………………………… 26 MAINTENANCE SCHEDULE…………………………………………………………………………………………………………………………… 27 OPERATION TIPS…………………………………………………………………………………………………………………………………………. 28 TROUBLESHOOTING……………………………………………………………………………………………………………………………………. 29 SYSTEM INFORMATION……………………………………………………………………………………………………………………………….. 30 CHARTS………………………………………………………………………………………………………………………………………………………. 31
WARNING: Failure to install and commission the product in compliance with these instructions, or failure to do the job properly and competently, may void the customer’s warranty. Further, it could expose the Installer and/or the Retailer to serious liability.
1

INTRODUCTION AND SAFETY
Congratulations on purchasing a new Gree Zone Controller. Please keep this Manual and the Warranty Booklet in a safe place, along with the original purchase documents, plus all relevant certificates of compliance relating to the installation work performed. Please register the Warranty straight away, by following the steps set out in the Warranty Booklet.
The installer must read the Installation Manual before installing the zone controller. The home owner/user should read the Owner’s Manual before operating the appliance.
To ensure the warranty on the appliance is continued and valid, the appliance must be checked and serviced by the home owner/user as per the requirements in the Maintenance & Service section and the Maintenance Schedule. This will also prolong the life of your appliance.
IMPORTANT!
THE AUSTRALIAN GREENHOUSE OFFICE HAS ISSUED VARIOUS REGULATIONS ON THE USE AND DISPOSAL OF REFRIGERANTS IN THE APPLIANCE. FAILURE TO FOLLOW THESE REGULATIONS MAY HARM THE ENVIRONMENT AND COULD LEAD TO THE IMPOSITION OF SUBSTANTIAL FINES.
WHERE SPECIFIED, ONLY QUALIFIED AND LICENSED TECHNICIANS SHOULD PERFORM WORK ON THIS APPLIANCE, FAILING WHICH THE WARRANTY ON THE APPLIANCE WILL BE VOID.
WARNING! This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance. If the supply cable is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
2

OPERATION
14 13 12

1 234

5

6 7

11 10 9

8

Fig 1.

NO. Name

Instructions

1 Name of the current zone
2 Decrease

– Shows the name of the current zone. The set temperature displayed on the home page is the temperature of the current zone.
– Press to switch to another zone.
Press to decrease the set temperature of the current zone

3 Set temperature display Shows the set temperature of the current zone

4 Mode display

Shows Cool, Dry, Fan, Heat and Auto modes.

5 Button 6 Time

– Press this button to turn on or off the screen. – Press this button for 5s to reset the screen.
– Shows the current time. – Press to enter the page of time menu to view or set the date and time.

7 Increase

Press to increase the set temperature of the current zone.

8 Zone button

Press to enter the page of zone control to set the name, temperature, on/off of each effective zone.

9 Fan button

Press to change the fan speed.

10 Current fan speed

Shows the current fan speed.

11 Mode button

Press to switch to another mode. COOL~DRY~FAN~HEAT~AUTO

12 On/Off button

Press to turn on or off the unit.

13 Menu button

Press to enter the page of menu.

14 Home button

Press to turn to the home page.

3

OPERATION
ONO/NOLFYFQUALIFIED AND LICENSED TECHNICIANS SHOULD INSTALL THIS UNIT, FAILING WHICH THE WARRANTY ON THE UNIT WILL BE VOID.
Press the top button to energise
Specific details are provided for thtshceeressecanrfeeisenisn,eisfrltveheiecpi.ng of equipment with flammable refrigerants in the Servce section of this manual.
Ensure this section is read and understood by personnel undergoing servicing to this equipment.
A risk assessment is an essential element that should be conducted before the commencement of work, to identify and eliminate the risk of falls or toNmotein: imize these risks by implementing control measureWs.hen ON
ON/OFF button shows OFF.
Aberfioskreacsosmesmsmenecnint gofaanlyl hwaozrakr,daonuWOsdshNhomte/waOnassFOykOFsFbNbFieu.sttroreenqquuiirreedd

MIsOthDerEe SanEoTnT-IgNoGing safety check system of

heUaqnrudniepermstsehenest,OarNonpdsewtsah,teelarodefdttehhreesyaaepnxpdisliaat cnoccneers,oso/lfisft,inagnchor pporeinstsstbheefoMreodtheebcuottmonmteonscweimtcehntthoef work? Iosptehrearteioan smyosdteems awshtichhe psreeqvueenntsceemployees from

wshoorkwingboenlowro.ofs if they are unwell or under the

influence of drugs or alcohol?

Are thereCaoonly special cDornyditions i.eF. aenxcessive roof pitch, limited ground area, fragile roof, electrical

power lines?

Auto

Heat

E Home

Room

Menu

Off

Mode

Cool
28 C
Low
Fan

08:30 AM
m Zone

Appliance is in Cool mode.
Cool

Fig 2.
get rid of the risk?
What is the best and safest access to the roof and working areas? If a worker is alone, who knows they are there and if
fficulty, how can they summon help?
underside or surface be checked? Does the worker have appropriate foot wear? Are all power cables/extension leads safe and appropriately rated? Are all ladders, tools and equipment suitable in good condition? Where ladders are to be used, is there a firm, stable base for them to stand on? Can they be tied or secured in some way at the top? Is the top of the ladder clear of electricity supply cables? Is there a roof anchor to attach a harness and lanyard to? If so, instruction should be issued for the use of an approved harness or only suitably trained people used. Are all tools and materials being used, prevented from slipping and falling onto a person at ground level? Is the area below the work area suitably protected to prevent persons walking in this area? Does the work schedule take into account weather conditions, allowing for work to be suspended in high winds, thunder storms/lightning or other types of weather giving wet, slippery surfaces?

E Home

Room

Menu

Off

Mode

Dry
28 C
Low
Fan

08:30 AM
m Zone

Appliance is in Dry mode.
Dry

E Home

Room

Menu

Off

Mode

Fan
28 C
Low
Fan

08:30 AM
m Zone

Appliance is in Fan mode.
Fan

Fig 3.

44

OPERATION cont.

TEMPERATURE SETTING

FAN SETTING

Adjust the SET temperature

Press the Fan button to vary the

Indowoirthuinnitthpeorsaitniogne 16-30°C.

The indoor unit needs to be positioned sosptheaetdist wasillsshuopwpnlyinairthteo seq8u-e9nce

the conditioned space doorways, and will not

wbeithbolouwt binegindgiroebcstltybrueoclnottewod.thbey

walls or occupants.

External walls should be well insulated to avoid heat loads

affectingPirtesssopeorration.

Low

Med-Low

Medium

Med-High

button to increase

Airflow

Room E

Home

Cool
20 C

08:30

TiAsMhbeeainirgiottscehromewdnpuehdencarriiteattiiatosucsnroaeenertw.rhdihee.esWnthitheocuototlhinegcaonrrde/cotr

heating amount

otoAf uaatoinr ytoaarenay

thTautrbo

8

area, that area will suffer from under conditioning.

High

Menu

Low

Please ensure the Unit has been sized to deliver the correct

m amount of air for proper cooling and heating.

Off

Mode

Fan

Zone

Fan is on low mode.

Outdoor unit

Check clearances, fix the unit in position, use ruE bbReoomr feet as 08:30 1AM2, 14, 20

supplied. Check installation position does not Hbomree ech maximCooul m

or minimum field installed pipe lengths.

21 C

Check the refrigerant charge matches the fieldMeinnu stalled pipLeow

Low

length. Pressing or

m

Ensure tchoentipniupoeuswly,ork is installed as required, inOffcludiMnogde useFaon f oil Zone

E Home

Room

08:30 AtMraps if rteeqmupierreadtu.re will
be increased or

Electrical
Menu

Cool
21 C
Low

decreased by 1°C every 0.5s.

Off

Mode

Fan

m Zone

Fan is on Medium mode.

Fig 4.

E Home

Room

Menu

Cool
21 C
Medium

08:30 AM

Medium

Off

Mode

Fan

m Zone

Note: For energy efficiency and lower operating cost we suggest operating your appliance as follows.

Cool: 24 ~ 30 C Heat: 16 ~ 20 C

E Home

Room

Menu

Off

Mode

Cool
21C
Turbo
Fan

08:30 AM
m Zone

Fan is on Trubo mode.
Turbo

Fig 5.

KSHVD1S SERIES OUTDOOR UNIT INSTALLATION MANUAL

55

OPERATION cont.

MEONNULYSQTRUUACLITFUIERDEAND LICENSED TECHNICIANS SHOULD INSTALL THIS UNIT, FAILING WHICH THE WARRANTY ON THE UNIT WILL BE VOID.

Main menu

SeqpueicpimfDiceadnilyet twtaimiitlsheraflraempmroavbidleerdeffroigr ethraenstasfien

servicing of the Servce

sectionWoefetkhtiismmeranual.

EunndsTeuwrrgeootWihnigesesskeetcrivmtiioceinrngis

read and understood to this equipment.

by

personnel

Zone control

Zone setting

AcornisMdkuaacintseszdeosnbseemfsoeertentitnthigseacnoemsmseenntciaelmeelenmt oefnwt tohrakt,

should be to identify

abnydimAelpwlilmaeyminsseeaotnttpeitneintgnhgezcoronisnektroofl

falls or to minimize measures.

these

risks

AberfioskrZeoacnsoesmespesmatstrimeannmgeceninttegorsfaanlyl hwaozrakr,daonuds

tasks is may be

required required

Connect RF remote

controller

Is there an on-going safety check system of harnesses, ropes, ladders and access/lifting equipment and where they exist on roofs, anchor points before the commencement of work? Is there a system which prevents employees from winoflrukeinngceonofrdoroufsgsifothr eaylcaorheoul?nFwreesllhoarirunder the Are there any special conditions i.e. excessive roof pitch, limited ground area, fragHielealrtohoyf, electrical power lines?
Quiet

Energy-Saving

I-Demand

Function

Holiday Low temperature dry

X-Fan

Clean remind

Date and time

Language
get rid of the risk? Lightness

System

WwBoharakctiknilsigghtahtreteimabsee?st and safest access to the roof and If a worker is alone, who knows they are there and if
Sound fficulty, how can they summon help?

Main or subsidiary

uwnirdeedrsciodnetroorllesrusrface be checked?

View

Does the worker have appropriate foot wear? Are aDll epbouwger cables/extension leads safe and

appropriately rated?

Are all ladders, tools and equipment suitable in good

Fig 6.condition? Where ladders are to be used, is there a firm, stable

base for them to stand on? Can they be tied or

secured in some way at the top? Is the top of the Theliandsdtreurctciolenasroonf tehleecfotrlilcoiwtyinsguppapglyescafobllleosw?s the above “Menu” structure.

  1. FuIsncthtieorne a roof anchor to attach a harness and 2. ZolanneySaredttitnog? If so, instruction should be issued for the

3. Syussteemof an approved harness or only suitably trained

4. Vipeewople used.

Are all tools and materials being used, prevented

from slipping and falling onto a person at ground

level? Is the area below the work area suitably

protected to prevent persons walking in this area?

Does the work schedule take into account weather

conditions, allowing for work to be suspended in high

winds, thunder storms/lightning or other types of

weather giving wet, slippery surfaces?

Memory Temperature unit
Reset WiFi
Parameter view Ambient temperature
of zone

64

FUNCTION

1. Fresh air 2. Healthy 3. Quiet 4. Save 5. I-Demand 6. Holiday

E Home

Menu Function

Menu

Zone View

On

System

7. Low Temperature dry 8. X-Fan 9. Filter Clean Remind 10. Memory 11. Temperature Unit 12. Reset WiFi
Press the Menu button on the home page to enter menu page.
Press “Function” to enter setting page.

Fig 7.
1. FRESH AIR

This is used to adjust the fresh

air volume indoors to improve air quality.

When setting the fresh air function, there are

10 fresh air modes that operate according to

the indoor fan running time. Optional

additional components are required

– speak to your installer, this function may

not be available.

1 – Fan will operate for 60

mins, fresh air damper will

E Home

Function Fresh Air

open for 6 mins. 2 – Fan will operate for 60

Menu

Healthy Quiet

mins, fresh air damper will open for 12 mins.

On

I-Demand

3 – Fan will operate for 60 mins, fresh air damper will open for 18 mins.

4 – Fan will operate for 60 mins, fresh air damper will open for 24 mins.

1

Cancel

Confirm

5 – Fan will operate for 60 mins, fresh air damper will open for 30 mins.
6 – Fan will operate for 60 mins, fresh air damper will open for 36 mins.

Fig 8.

7 – Fan will operate for 60 mins, fresh air damper will open for 42 mins.

8 – Fan will operate for 60 mins, fresh air damper will open for 48 mins.

9 – Fan will operate for 60 mins, fresh air damper will open for 54 mins.

10 – Fan will operate for 60 mins, fresh air damper is always open.

2. HEALTHY
This function controls the operation of an optional air purifier. Optional additional components are required – speak to your installer, this function may not be available.

E Home

Function Fresh Air

Menu

Healthy Quiet

On

I-Demand

Press the Menu button on the home page to enter function page.
Press “Healthy” to enter function page.

On

Cancel

Confirm

Press the and buttons to turn the function On/Off.
Press “Confirm” to return to the previous page.

Fig 9.
3. QUIET

QUIET function can be activated to use lower indoor fan speeds to reach the SET temperature when in AUTO, COOL and HEAT modes.

E Home

Function Fresh Air

Menu

Healthy Quiet

On

Save

Press Menu button on the home page to enter the function menu.
Press “Quiet” to enter the setting.

On

Cancel

Confirm

Fig 10.

Press the and buttons to turn the function On/Off. Press “Confirm” to return to the previous page.
7

FUNCTION cont.

4. SAVE

By setting the lower limit of set temperature for cool and dry modes and the upper limit of set temperature for heat mode, the appliance will run in a smaller temperature range, to save energy.

E Home

Function Fresh Air

Menu

Healthy Quiet

On

Save

Press the Menu button on the home page to enter function page.
Press “Save” to enter function page.

Cool limit Heat limit

On

22ºC

24ºC

Cancel

Confirm

Press the and buttons to set the values.
Press “Confirm” to return to the previous page.

Fig 11.

5. I-DEMAND
When the appliance is first turned on in COOL or HEAT modes, set I-Demand. Limiting the maximum power usage 75%. Set temperature is fixed at 27 C and auto fan speed.

E Home

Function Fresh Air

Menu

Healthy Quiet

On

I-Demand

Press the Menu button on the home page to enter function page.
Press “I-Demand” function page.

On

Cancel

Confirm

Fig 12.
8

Press the and buttons to turn the function On/Off.
Press “Confirm” to return to the previous page.
Note: Refer to page 32 for I-Demand Chart.

6. HOLIDAY

This is used to maintain indoor temperature so that unit can perform heating quickly upon return. Holiday function is only available in heat mode and fixed at 8 degrees.

E Home

Function Holiday

X-Fan Menu

On

Press the Menu button on the home page to enter function page
Press “Holiday” to enter function page.

On

Cancel

Confirm

Press the and buttons to turn the function On/Off.
Press “Confirm” to return to the previous page.

Fig 13.
7. LOW TEMPERATURE DRY The appliance runs in dry mode at low temperature. Activating this function reduces the dry set temperature from 16 C to 12 C

E Home

Function I-Demand

Menu

Holiday Low temperature dry

On

X-Fan

Press the Menu button on the home page to enter function page.
Press the “Low temperature dry” function page.

On

Cancel

Confirm

Fig 14.

Press the and buttons to turn the function On/Off.
Press “Confirm” to return to the previous page.

FUNCTION cont.

8. X-FAN
The X-FAN function can be used in COOL or DRY modes, to continue operation of the indoor fan after the system is turned off (to remove excess moisture from the indoor coil).

E Home

Function I-Demand

Menu

Holiday Low temperature dry

On

X-Fan

Press the Menu button on the home page to enter function page.
Press “X-Fan” to enter function page.

On

Cancel

Confirm

Press the and buttons to turn the function On/Off.
Press “Confirm” to return to the previous page.

Fig 15.
9. FILTER CLEAN REMIND

When this function is enabled, the appliance will record its operation time. When the set time is reached, the user will be reminded to clean the filter.

E Home

Function Clean remind

Menu

Memory Temperature unit

On

Reset WiFi

Press the Menu button on the home page to enter function page.
Enter “clean remind” function page.

Level

Time

Off

01 5500Hour

Cancel

Confirm

Fig 16.

Press the and buttons to set the level and time.
Press “Confirm” to save.
Note: Refer to page 31 for filter clean remind table.

10. MEMORY
The unit resumes the original ON/OFF state when power is restored after power failure.

E Home

Function Clean remind

Menu

Memory Temperature unit

On

Reset WiFi

Press the Menu button on the home page to enter function page.
Press “Memory” to enter function page.

On

Cancel

Confirm

Press the and buttons to turn the function On/Off.
Press “Confirm” to return to the previous page.

Fig 17.
11. TEMPERATURE UNIT
The temperature can be set in Fahrenheit or Celsius.

E Home

Function Clean remind

Menu

Memory Temperature unit

On

Reset WiFi

Press the Menu button on the home page to enter function page.
Press “Temperature unit” to enter function page.

oC

Cancel

Confirm

Fig 18.

Press the and buttons to alternate between celsius C or fahrenheit F.
Press “Confirm” to return to the previous page.
9

FUNCTION cont.

12. RESET WIFI
Reset the WiFi module for network connection.

E Home

Function Clean remind

Menu

Memory Temperature unit

On

Reset WiFi

Press the Menu button on the home page to enter function page.
Press “Reset WiFi” to enter function page.

Reset WiFi?

Cancel

Confirm

When in Reset WiFi page, press the Confirm button to reset WiFi.

Fig 19.

10

ZONE SETTING

1. Daily Timer 2. Week Timer 3. Two Week Timer 4. Zone control

5. Main Zone Setting 6. Always Open Zone 7. Zone Parameter setting 8. Connect RF Remote Controller

1. DAILY TIMER

In daily timer function, the timer can be set into 8 segments. In each segment you can set the time when the appliance turns ON/OFF and temperature for COOLING/HEATING.

E Home

Menu Function

Menu

Zone View

On

System

Press Menu button on the home page to enter the function menu.
Press “Zone” to enter the page of zone setting.

E Home

Zone Daily timer

Menu

Week timer Two Week timer

On

Zone control

Press “Daily timer” to enter the page for zone selection.

E Home

Daily timer Zone_1

On

Zone_2

Zone_3

Menu

Zone_4

Zone_5

Zone_6

Zone_7

Zone_8

On

Set

Press the “On/Off” button to turn on or off the timer function.

E Home

Daily timer Zone_1

On

Zone_2

Zone_3

Menu

Zone_4

Zone_5

Zone_6

Zone_7

Zone_8

On

Set

Fig 20.

Select the zone or zones to activate. Then press “Set” to enter the timer setting page.

E

Daily timer

Save

Home 1 00:00 26ºC Off

Menu

2 00:00 26ºC Off 3 00:00 26ºC Off

On 4 00:00 26ºC Off

After entering the timer page, there are 8 sets of timers that can be set.
Press the and buttons to scroll down the page.

12 : 30

Cancel

Confirm

28

Cancel

Confirm

E

Daily timer

Save

Home 1 12:30 28ºC Off

Menu

2 00:00 26ºC Off 3 00:00 26ºC Off

On 4 00:00 26ºC Off

Press the on time button to set the desired On time.
Press the or button to select timer hour or minute.
Press “Confirm” to save.
Press on the temperature button to set the desired temperature for the zone.
Press the or button to set the temperature.
Press “Confirm” to save.
Repeat for time setting 2 – 8 as desired
Press the Save button to “Confirm”.

Fig 21.
Note: 1. We recommend using the 24 hour clock as this avoids improper setting of the clock functions.
2. The timer must be set (between 00:01 and 23:59), failure to do so will cause malfunction.
3. Ensure the timer settings are in chronological order and they must be all within the same day (between 00:01 to 23:59).

11

ZONE SETTING cont.

2. WEEK TIMER
The user can set the everyday timer content for a week. In each day, 8 segments can be set for the timer. The appliance will execute corresponding timer settings in a week.

E Home

Menu Function

Menu

Zone View

On

System

Press Menu button on the home page to enter the function menu.
Press “Zone” to enter the page of zone setting.

E Home

Zone Daily timer

Menu

Week timer Two Week timer

On

Zone control

Press “Week timer” to enter the page for zone selection.

E Home

Week timer Zone_1

On

Zone_2

Zone_3

Menu

Zone_4

Zone_5

Zone_6

Zone_7

Zone_8

On

Set

Select the zone or zones to activate.
Press “Set” to enter the timer setting page.

E Home

Weekly timer
SUN MON

TUE

WED

Menu
THU FRI SAT

On

Set

Fig 22.

Select the days to activate.
Press “Set” to enter the timer setting page.

12

E

Week timer

Save

Home 1 00:00 26ºC Off

Menu

2 00:00 26ºC Off 3 00:00 26ºC Off

On 4 00:00 26ºC Off

After entering the page of timer setting, there are 8 sets of timers that can be set.
Press the and buttons to scroll down the page.

01 : 30

Cancel

Confirm

29

Cancel

Confirm

E

Week timer

Save

Home 1 01:30 28ºC Off

Menu

2 00:00 26ºC Off 3 00:00 26ºC Off

On 4 00:00 26ºC Off

Press on the time button to set the desired On time.
Press the or button to select timer hour or minute.
Press “Confirm” to exit.
Press on the temperature button to set the desired temperature for the zone.
Press the or button to set the temperature
Press “Confirm” to return to main menu.
Repeat for time setting 2 – 8 as desired
Press the “Save” button to confirm.

Fig 23.
Note: Ensure the timer settings are in chronological order and they must be all within the same day (between 00:01 to 23:59)

ZONE SETTING cont.

3. TWO WEEK TIMER
The user can set the everyday timer content for two weeks, in each day the 8 segments can be set for each timer. The unit will execute the timer setting for two weeks.

E Home

Menu Function

Menu

Zone View

On

System

Press Menu button on the home page to enter the function menu.
Press “Zone” to enter the page of zone setting.

E Home

Zone Daily timer

Menu

Week timer Two Week timer

On

Zone control

Press “Two week timer” to enter the page for zone selection.

E Home

Two week timer

Zone_1

Zone_2

On
Zone_3

Menu

Zone_4

Zone_5

Zone_6

Zone_7

Zone_8

On

Set

Select the zone or zones to activate.
Press “Set” to enter the timer setting page.

E Home

Two Week setting
First

Menu
Second

On

Fig 24.

Select the required week to program by pressing “First” or “Second”.

E Home

Two week timer
SUN MON

TUE

WED

Menu
THU FRI SAT

On

Set

Select the days to activate.
Press “Set” to enter the timer setting page.

E

Two week timer

Save

Home 1 00:00 26ºC Off

Menu

2 00:00 26ºC Off 3 00:00 26ºC Off

On 4 00:00 26ºC Off

After entering the page of timer setting, there are 8 sets of timers that can be set.
Press the and buttons to scroll down the page.

01 : 30

Cancel

Confirm

E Home

Two Week setting
First

Menu
Second

On

Set the desired temperature for the zone.
Press the or button to set the time and temperature
Press “Confirm” to save.
Repeat the same process for the second week.

Fig 25.
Note: Ensure the timer settings are in chronological order and they must be all within the same day (between 00:01 to 23:59)

13

ZONE SETTING cont.

4. ZONE CONTROL

The zone control setting can be used to set zone names, temperature, turn zones On or Off. Zone names must be selected from the list preselected names.

E Home

Zone Daily timer

Menu

Week timer Two Week timer

On

Zone control

Press Menu button on the home page to enter the function menu.
Press “Zone” to enter the page of zone setting.

E

Zone control

Home 1 Zone_1

Menu

2 Zone_2 3 Zone_3

On 4 Zone_4

26ºC

On

26ºC

On

26ºC

On

26ºC Off

8 zones can be set, each page will display 4 zones.
Press the or buttons to change the page.

Name

No.

Zone

1

Cancel

Confirm

Press the name of each zone to enter the page of name setting.
Press the and buttons to set the name of a specific zone.

Name

No.

Other

1

Cancel

Confirm

Fig 26.

14

Note: Your Gree installer may set the following on your behalf at commissioning to ensure everything is connected and operating correctly. The following information will assist you in adjusting the time, or, renaming of the zones.

Name

No.

Other

2

Cancel

Confirm

Press the and buttons to set the number of a specific zone.
Note: number must match the RF remote sensor, if used.

E

Zone control

Home 1 Kitchen

22ºC

On

Menu On

2 Bedroom 3 Playroom 4 Bath

23ºC

On

24ºC

On

25ºC Off

Set the temperature of each zone.
Press the and buttons to set temperature.
Press “Confirm” to save the setting.

E

Zone control

Home 5 Coffee

Menu

6 Hall 7 Guest

On 8 Other

26ºC

On

27ºC

On

28ºC

On

29ºC Off

Press the “On/Off” button of each zone to turn on or off the zone.

Fig 27.

The following zones names can be set.

1. Hall 2. Bath 3. Kitchen 4. Playroom 5. Hovel

6. Coffee 7. Study 8. Baby 9. Dining 10Bedroom

11. Guest 12. Host 13. Zone 14. Other

ZONE SETTING cont.

5. MAIN ZONE SETTING
Set the main zone on the system, the main zone is usually the largest area. Zone 1

E Home

Zone Main zone setting

Menu

Always open zone setting Zone parameter setting

On

Connect RF remote controller

Press Menu button on the home page to enter the zone menu.
Press “Zone” to enter page.

E Home

Main zone settings

Zone_1

Zone_2

Zone_3

Menu

Zone_4

Zone_5

Zone_6

Zone_7

Zone_8

On

Set

Select the zone that is going to be the main zone.
Press “Confirm” and return to the previous page.

Fig 28.
6. ALWAYS OPEN ZONE A zone must always be open for the system to operate.

E Home

Zone Main zone setting

Menu

Always open zone setting Zone parameter setting

On

Connect RF remote controller

E Home

Always open zone setting

Zone_1

Zone_2

Zone_3

Menu

Zone_4

Zone_5

Zone_6

Zone_7

Zone_8

On

Set

Press Menu button on the home page to enter the function menu.
Then press “Zone” to enter page.
Press “Always open zone setting”.
Select the zone that is going to be the always open zone.
Press “Confirm” and return to the previous page.

Fig 29.

7. ZONE PARAMETER SETTINGS
The area of each zone can be set, If an RF remote is being used, “Sensor” will need to be activated.

E Home

Zone Main zone setting

Menu

Always open zone setting Zone parameter setting

On

Connect RF remote controller

E

Zone parameter setting

Home 1 Use

0m Sensor

Menu

2 Use 3 Use

0m Sensor 0m Sensor

On 4 Use

0m Sensor

Press Menu button on the home page to enter the function menu.
Press “Zone” to enter page.
Press “Zone parameter setting”.
Select the zone to be used.
Find the area of the room by measuring the length and then the width of the room. Then multiply the length and width.

75

Cancel

Confirm

Press the or button to adjust the required zone size. To calculated measurement
Press “Confirm” to save.

E

Zone parameter setting

Home 1 Use

75m Sensor

Menu

2 Use 3 Use

0m Sensor 0m Sensor

On 4 Use

0m Sensor

Select Sensor for the zone is equipped with a temperature controller.
Press the return symbol to return add icon.

Fig 30.
Note: Zone 1 must have an RF remote. The wired wall control does not measure the room temperature. All RF remotes must be set and matched to the Wired Wall Control.

15

ZONE SETTING cont.

8. CONNECT RF REMOTE CONTROL

When using RF remote controller for the first time, the RF control will need to be paired with the zone control interface.

E Home

Zone Main zone setting

Menu

Always open zone setting Zone parameter setting

On

Connect RF remote controller

Press Menu button on the home page to enter the function menu.
Then press “Connect RF remote controller” to pair RF remote.

Connect RF remote controller ?

Cancel

Confirm

Press “Confirm” to pair the RF remote.

E

Connect RF Remote Controller

Home RF Remote Controller 1……

Menu

On

Press “Exit” to end the pairing.

Fig 31.
Note: RF controller is required for pairing.

ON the RF remote

press the ON and

ON

OFF buttons at the same time for

5s.

OFF

When green and

red indicator flash

ON

on and off alternatively this

means the RF

remote controller

has entered into

OFF

the pairing mode.

ON OFF Fig 32.

If pairing is successful, the green indicator will flash quickly for 10s and then exit from pairing mode. The wired wall control will show the zone number.

Note: If the RF controller does not pair within 5 minutes, the red indicator will flash quickly for 10s and then exit pairing mode. If pairing is successful, the green indicator will flash quickly for 10s and exit pairing mode.

16

SYSTEM

1. Date and time 2. Language 3. Lightness 4. Backlight time

5. Sound 6. Main or Subsidiary
wired controllers 7. Debug

1. DATE AND TIME

The date setting is used to set the date.

E Home

System Date and time

Menu

Language Lightness

On

Backlight time

Press Menu button on the home page to enter the system menu.
Press “System” to enter page.

E Home

Date and time Date: 2020/11/17

Menu

Time: 23:41 Time format: 24-hour

On

Press “Date”, “Time”, and “Time format” to enter the setting page.

2020 11

17

Cancel

Confirm

Fig 33.

Use the and buttons to adjust the year, month, day.
Press “Confirm” to save.

1. DATE AND TIME
The “Time” setting is used to set the date and time.

E Home

Date and time Date: 2020/11/17

Menu

Time: 23:41 Time format: 24-hour

On

Press “Date”, “Time”, and “Time format” to enter the setting page.

23 : 41

Cancel

Confirm

Use the and buttons to adjust hour and minute.
Press “Confirm” to save.

Fig 34.
HOUR FORMAT SETTING
The time format can be set to either 12 hour or 24 hour.

24-hour

Cancel

Confirm

Use the and buttons to adjust between 24-hour and 12-hour time.
Press “Confirm” to save.

Fig 35.
Note: We recommend using 24 hour time to prevent timer settings being set across 2 days. A timer setting (Daily, Week, two Week) must be set for one day. The day starts at 00:01 and finishes at 23:59.

17

SYSTEM cont.

2. LANGUAGE SETTING
Set the desired language for the system.

E Home

System Date and time

Menu

Language Lightness

On

Backlight time

Press Menu button on the home page to enter the System menu.
Press “Language” to enter the setting.

English

Cancel

Confirm

Fig 36.

Select the desired language
Press “Confirm” to save.

3. LIGHTNESS SETTING
Adjust the screen brightness setting to vary the screen brightness as shown in the sequence below.

90%

70%

50%

10%

30%

E Home

System Date and time

Menu

Language Lightness

On

Backlight time

Press Menu button on the home page to enter the System menu.
Press “Lightness” to enter the setting.

90%

Cancel

Confirm

Fig 37.

Press the or button to adjust the lightness.
Press “Confirm” to save the setting and return.

18

SYSTEM cont.

4. BACKLIGHT TIME SETTING
Adjust the backlight On time to vary the time as shown in the sequence below.

Always on
30 Min

15 Sec 10 Min

30 Sec 5 Min

1 Min 3 Min

E Home

System Date and time

Menu

Language Lightness

On

Backlight time

Press Menu button on the home page to enter the system menu.
Press “Backlight time” to enter the setting.

Always on

Cancel

Confirm

Fig 38.

Press the or button to adjust the backlight setting.
Press “Confirm” to save the setting and return.

5. SOUND SETTING
Turn the sound On/Off through the sound setting.

E Home

System Sound

Menu

Main or subsidiary controller Debug

On

Press Menu button on the home page to enter the system menu.
Press “Sound” to enter the setting.

Off

Cancel

Confirm

Fig 39.

Press the or button to change the backlight setting.
Press “Confirm” to save the setting and return.

19

SYSTEM cont.

6. MAIN OR SUBSIDIARY CONTROLLER
This function must be set at wired wall controller that is connected to port 2 on the zone control interface.

E Home

System Sound

Menu

Main or subsidiary controller Debug

On

Press Menu button on the home page to enter the system menu.
Press “Main or subsidiary controller” to enter the setting.

Main Subsidiary

Cancel

Confirm

Select a main or subsidiary wired wall control.

Main Subsidiary

Cancel

Confirm

Press “Confirm” to save the setting and return.

Fig 40.
Note: Wired wall control is connected to controller port 1 on zone control interface is “Main”.
Wired wall control is connected to controller port 2 on zone control interface is “Subsidiary”.

7. DEBUG
Debug setting can only be entered by an authorised technician. This proceedure is done at commissioning.

E Home

System Sound

Menu

Main or subsidiary controller Debug

On

Press Menu button on the home page to enter the system menu.
Press Debug button on the home page to enter the system menu.

E Home

System Sound

Menu

MainPororfseusbsisoidniaalrcyacnosnettr!oller Debug

On

Fig 41.

20

VIEW

PARAMETER VIEW
The outdoor and ambient temperatures of the zones can be viewed from the “View” Menu.

E Home

Menu Function

Menu

Zone View

On

System

Press Menu button on the home page to enter the view menu.
Press “View” to enter the page.

E Home

View Parameter view

Ambient temperature of zone Menu

On

E Home

Parameter view Outdoor temperature: – –
Clean remain time: – –

Menu

On

Fig 42.

Press “Parameter view” to enter the page of parameter view.
The outdoor temperature will be displayed, as well as the time left before cleaning.

AMBIENT TEMPERATURE OF ZONE
The ambient temperature of each zone can be viewed.

E Home

View Parameter view

Ambient temperature of zone Menu

On

Press Menu button on the home page to enter the view menu.
Press “Ambient temperature of zone” to enter page.

E Home
Menu

Ambient temperature of zone Zone_1: – Zone_2: – Zone_3: – –

On

Press “Ambient temperature of zone” and you can view the ambient temperature of the zones.

Fig 43.
VIEW MALFUNCTION

When there is a malfunction, the icon of malfunction will be displayed on the home page.

E Home

Room

Menu

Off

Mode

Cool
20 C
Low
Fan

08:30 AM
m Zone

Press the icon of malfunction to enter the page of malfunction information.

Zone information need to be set! 1. Set the zone’s area 2. Select the always open zone 3. Select the main zone

Cancel

Confirm

Fig 44.

The screen will display the error message information.
21

WIFI MODULE INSTALLATION

OPTIONAL PART – ME31-00/C13

The WiFi app can be installed at the same time as the zone control system, or, purchased and added to the zone control system at a later date.

1

2

3

NO. Name

1 Screw Hole

RESET

G – Cloud

2 Reset Button 3 Screw Hole

4

Fig 45.

4 Communication cable

1. Connect the Wifi Module to Wifi Module port on the zone controller.

HBS RS485

WIFI Module

Wired Wired

Remote Remote

Controller Controller

1

2

Extension

Wifi Module

RESET

G – Cloud

Fig 46.

2. Secure the Wifi Module to a suitable surface with screws.

APP DOWNLOAD Control the air conditioner and track the running status through the internet.

Requirements for User’s smart phone:
iOS system Support iOS 8.0 and above version

Android system Support Android 4.4 and above version

Fig 47.

Scan the QR code or search “Ewpe Smart or GREE+ App” from the application market to download and install it. When “Ewpe Smart or GREE+ App” is installed, register your account and add the device to achieve long distance control and LAN control of smart home devices. For more information, please refer to “Help” in the App.

EWPE Smart App

App Download Link

22

GREE+ App

Fig 48.

WIFI MODULE INSTALLATION cont
EWPE SMART or GREE+ APP
Open up the EWPE SMART or GREE+ APP application select the zone controller icon.

Connect to the appliance WiFi, press Next.

3 Step Process
1. Connect to the appliance manually.
2. Connect to the end user home WiFi.
3. Follow the on screen prompts to start the connection process.

Confirm connection press Connect.

Fig 49.

Fig 50.
23

WIFI MODULE INSTALLATION cont
EWPE SMART or GREE+ APP cont.
Next connect to the home Wi-Fi network, select your home Wi-Fi network enter your password for Wi-Fi network. Press Next Note: you can view password by pressing the eye icon. Process can take up to two minutes.
Next connect to the home Wi-Fi network, Press Connect.

The zone control will now be able to be control through the application.
Fig 52.

Fig 51.
24

ERROR CODES

Error Code C5 E1 E2 E3 E4 E6 E8 E9 EE ee

Error Description

Error Code Error Description

Temperature sensor error of wired controller
Compressor high pressure protection

Lc

Activation failure

Ld

Compressor phase sequence protection

Indoor anti-freeze protection

LF

Power protection

Compressor low pressure protection, low refrigerant

Lp

Indoor and outdoor mismatch

Protection and refrigerant collecting mode

P0

Drive reset protection

Compressor high discharge temperature protection

P5

Over-current protection

Communication error

P6

Communication error between main control and drive

Indoor fan motor error

P7

Drive module sensor error

Capacity code error

P8

Drive module over temperature protection

Drive memory chip error

P9

Zero passage protection

F0

Full water protection

PA

AC current protection

F1

Indoor ambient temperature sensor error

Pc

Drive current error

F2

Evaporator temperature sensor error

Pd

Sensor connecting protection

F3

Condenser temperature sensor error

F4

Outdoor ambient temperature sensor error

F5

Discharge temperature sensor error

PE

Temperature drift protection

PF

Outdoor memory chip error

PH

Bus high voltage protection

H3

Electric box sensor error

PL

Bus low voltage protection

H4

Compressor overload protection

PP

Input voltage abnormality

H5

Overloading

H6

IPM protection

H7

DC fan motor error

PU

Charge loop error

U7

4-way valve direction changing protection

Hc

Drive desynchronizing protection

L1

PFC protection

25

NORMAL OPERATION CODES

Code D1 D2 D3

Description Dred 1 Dred 2 Dred 3

Code H1 E2

Description
Defrost Mode
This may appear when in cooling and indoor airflow has been reduced for an extended period of time. Cooling is stopped momentarily to prevent the indoor coil from freezing.

MAINTENANCE & SERVICE
AIR FILTER It is important to check and clean the air filter as per the maintenance Schedule below. A dirty air filter will not allow the correct amount of clean air to pass through your air conditioner, resulting in poor performance and increased running costs. You should ask the installer to show you where the air filter is located. To clean the air filter, it should be removed and then cleaned with a vacuum cleaner. If it is very dirty, wash it with soapy water and then wipe off. Make sure it is completely dry before refitting it. You should never operate the air conditioner without the air filter in place.
INDOOR COIL It is advisable to have the drain connections checked on an annual basis (as set out in the Maintenance Schedule). Drains can be blocked by all types of insects, and rats have been known to chew through the drain to get to the water in the pipe.
OUTDOOR UNIT The Outdoor unit has either one or two fans, it draws air through the appliance to expel the heat generated during the cooling cycle. We recommend checking that plants haven’t grown into or around the air intake or outlet, along with other debris that may build up over time, namely, leaves and the like.
REFRIGERANT The refrigerant is the life blood of your air conditioning unit. Not only does the correct refrigerant charge provide you with reliable and economical cooling, it also provides the air conditioning for the compressor. A lack of refrigerant, due to a leak, will cause the compressor to overheat and expire prematurely. You will notice a decline in air conditioning effect and an increase in power consumption. Therefore, having a qualified, licensed technician service your appliance will save you money in the long term.
PLEASE REFER TO THE NEXT PAGE FOR THE MAINTENANCE SCHEDULE

26

MAINTENANCE SCHEDULE

Installation Date:

/

/

Installer:

Items to be done by the Home Owner/User (please sign in the places indicated) Monthly Annually Year 1 Year 2 Year 3 Year 4 Year 5
Air filter cleaning
Air filter replacement Maintain required clearance around Outdoor unit

Items to be done by a Qualified Licensed Technician (Home owner/user must ensure that the technician signs and dates in the places indicated)
Annually Check, clean or replace filter Check drain from indoor coil Check Outdoor unit clearances ­ maintain garden and debris (refer diagram p28) Check refrigerant charge Check refrigeration connections for soundness Check outdoor fans Check electrical connections Check overall installation Report to the home owner/user all tasks that require attention

Year 1 ­ Date: Year 2 ­ Date: Year 3 ­ Date: Year 4 ­ Date: Year 5 ­ Date: Year 6 ­ Date:

/

/

/

/

/

/

/

/

/

/

/

/

Technician: Technician: Technician: Technician: Technician: Technician:

Please NOTE: the Maintenance Schedule covers Year 1 to Year 6. To preserve your investment for many years afterwards, we strongly recommend that you continue to maintain and service the Gree Ducted Inverter Air Conditioning appliance as per the items and frequency set out in the Schedule, and as indicated elsewhere in this Manual.

27

OPERATION TIPS
The following events may occur during normal operation:
1. Protection of the air conditioner. Compressor protection · The compressor cannot restart for 3 minutes after it stops.
2. A white mist coming out from the Indoor unit. · A white mist may generate due to a large temperature difference between air inlet and air outlet on COOL mode in an indoor mode in an indoor environment that has a high relative humidity.
3. Low noise of the air conditioner. · You may hear a low hissing or gurgling sound when the compressor is running or has just stopped running. This sound is the sound of the refrigerant flowing or coming to a stop. · You can also hear a low “squeak” sound when the compressor is running or has just stopped running. This is caused by heat expansion and cold contraction of the plastic parts in the appliance when the temperature is changing.
4. Dust is blown out from the Indoor unit. This is a normal condition when the air conditioner has not been used for a long time or during first use of the appliance.
5. A peculiar smell comes out from the Indoor unit. This is caused by the Indoor unit giving off smells permeated from building material, from furniture, smoke (for example if someone is cooking food, candles, incense), or from the duct work.
6. FAN operation during COOL mode. When indoor air temperature reaches the setting on the wired wall control, control, the compressor will stop operating and after approximately 60 seconds the indoor fan will stop blowing air. Unless X-Fan has been activated where the indoor fan will continue for some minutes to dry the coil of the indoor unit. When the room temperature rises back to the set point, the indoor fan and the compressor will start again.
CLEARANCES

Fig 53.

A~E
B A,B,C
B,E A,B,C,E
D D,E

Hb Hd H
— — — — — —

a — 300 — 300 — —

b 100 100 100 150
— —

(mm)

c

d

e

100 —

— 1000

150 — 1000

— 1000 —

— 1000 1000

Note: Distance in front of the outdoor may be reduced with the use of the Gree air deflection grilles. Consult your installer for more information.

28

TROUBLESHOOTING

Problem
1. The air conditioner does not run.

Probable Cause

Remedy

1.1 Power failure. 1.2 Fuse blown or circuit
breaker open. 1.3 Thermostat adjustment
too low (in heating mode) or too high (in cooling mode).

1.1 Wait for power to resume. 1.2 Replace the fuse or reset
the breaker. 1.3 Check thermostat setting.

2. There is insufficient 2.1 The room was probably

cooling.

very hot when you

started the system.

2.1 Wait a while so the appliance has enough time to cool the room.

3. `Clicking’ sound is heard from the air conditioner.

3.1 In heating or cooling operation any plastic parts may expand or shrink due to a sudden temperature change in this event, a clicking sound may occur.

3.1 This is normal.

WARRANTY & SERVICE
For prompt, efficient service, please follow the above before calling the appropriate number below.
For Warranty 1800 4733 463
When calling the Warranty Service number, please ensure you have your model and serial number available, along with date of purchase, and if possible a description of the problem or the error code.
NOTE: Gree Australia strives for continuous product improvements, therefore specifications are subject to change without notice. Unit colour may vary slightly from that depicted in this booklet. Installation and commissioning of this system to the manufacturer’s specification, and compliance with industry standards, and local, state and national regulatory codes, are the responsibility of the installer. Information in this booklet was true and correct at the time of publishing.

29

SYSTEM INFORMATION

Table to be filled in by a Qualified Licensed Technician (Home owner/user must ensure that the technician signs and dates in the places indicated) INSTALLATION INFORMATION

Installation Date: ………………………………………….

Installer: …………………………………………………

MODEL INFORMATION Indoor model number ………………………………………

Serial Number……………………………………………

Outdoor model number ……………………………………. Number of zones …………………………………………… Number of zone motors ………………………………..

Serial Number…………………………………………… Wi-Fi module location ………………………………… Wired Wall control location ………………………….

Number of RF Remotes ………………………………..

Is Wi-Fi connected……………………………………..

ZONE INFORMATION

Zone number 1 Zone number 2 Zone number 3 Zone number 4 Zone number 5 Zone number 6 Zone number 7 Zone number 8

Area ……………………. m² Area ……………………. m² Area ……………………. m² Area ……………………. m² Area ……………………. m² Area ……………………. m² Area ……………………. m² Area ……………………. m²

Zone name ………………………………………………. Zone name ………………………………………………. Zone name ………………………………………………. Zone name ………………………………………………. Zone name ………………………………………………. Zone name ………………………………………………. Zone name ………………………………………………. Zone name ……………………………………………….

30

CHARTS

FRESH AIR FUNCTION

Operating Time
60
50
40
30
20
10
0 1

Fresh air activated time during IDU operating

2

3

4

5

Fresh air damper on

6

7

8

9

Fresh air damper off

10
Level

AIR function level 1 ~ 10 are available for wired wall controller . 1 ~ 2 are available for wireless wall controller.
Fig 54.

FILTER CLEANING REMINDER

Pollution level
1 1 1 1 1 1 1 1 1 1

Accumulated operating time (hour)

Pollution level

5,500

2

6,000

2

6,500

2

7,000

2

7,500

2

8,000

2

8,500

2

9,000

2

9,500

2

10,000

2

Accumulated operating time (hour)
1,400 1,800 2,200
2,600 3,000 3,400 3,800 4,200 4,600 5,000

Pollution level

Accumulated operating time (hour)

3

100

3

200

3

300

3

400

3

500

3

600

3

700

3

800

3

900

3

1000

Cleaning remind of air return inlet’s filter according to pollution level (air quality) to select the accumulated operating time.
Fig 55.

31

CHARTS cont.

DRED

100% 80% 60% 40% 20% 0% T0

Input Power Rate DRED3
DRED2

DRED1 T1

T2

T3

Signal drop
T4 T5

I-DEMAND
Power
100 75%
50

0

0

12

Time 24

For national power shortage, response to DRED signal within 1 second. Where DRED function is connected, the power supply authority may limit the amount of power being consumed by switching the DRED signal on the appliance.
Fig 56.
Satisfy the basic cooling requirement, with saving power up to 25%. After setting the fan speed is fixed at AUTO. This function limits the power usage to 75%, thus cooling or heating your space may take a little longer, but this function will also reduce the power consumed to do so. Under I-Demand the set point is fixed at 27 C and the indoor fan is fixed at AUTO.
Fig 57.

32

NOTES
33

It is the policy of Gree New Zealand to introduce continuous product improvements. Accordingly, specifications are subject to change without notice. Please consult with your dealer to confirm the
specifications of the model selected.
Warranty Service 0800 289 4733
hello@greeac.co.nz

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals