AVID POWER ACSD368 Electric Screwdriver Operating Manual
- March 21, 2024
- Avid Power
Table of Contents
AVID POWER ACSD368 Electric Screwdriver
- MODEL: ACSD368
4V CORDLESS SCREWDRIVER
Operator’s Manual
SAVE THIS MANUAL
- You will need this manual for safety instructions, operating procedures, and warranty.
- Put this manual and the original sales receipt in a safe dry place for future reference.
IMPORTANT SAFETY INSTRUCTIONS
The following recommendations should be strictly complied with before operating the too to avoid damage to the equipment and hazard to the user.
- Wear individual protection equipment if necessary (gloves, shoes, eye protectors, breathing filters, etc.). Do not wear jewels; protect long hair and wear close-fitting clothes.
- Don’t charge when you replace a tool or maintain the equipment.
- Work in a clean and tidy room with sufficient lighting.
- Place and store the tool in a dry place far from heat or dangerous vapors (the best temp is between 10 and 15°C). Do not operate the machine close to explosive substances or inflammable matter.
- This do-it-yourself equipment should be used as such and not be considered heavy-duty equipment.
- Do not work close to people, in particular children if work is hazardous. Keep tools away from children during and after work.
- Make sure your body position is steady as you work. Remember that falls constitute an important source of accidents.
- Make sure you do not use the drill or screwdriver on live parts to avoid electric shock. (a metal detector may be used for that purpose ). Do not touch the chuck, socket, or drill bit, when the tool is working.
- Do not try to open or disassemble the tool, only a specialist using original parts and manufacturer’s drawings is allowed to service the tool.
- Should the case be damaged (wires or plug) have it replaced immediately by the after-sales department.
- This tool does not require special maintenance. The same applies to the electric part of the tool.
- Plastic parts should be cleaned only after disconnecting the charger. Use a wet cloth and soft soap. Do not immerse the tool or the USB cable. The use of solvent, alcohol, petrol, etc. is prohibited.
Please contact the after-sales department for complete cleaning of the tool.
SPECIFICATIONS
| Parameter | Value |
|---|---|
| No Load Speed | 200 rpm |
| Chuck Size | 1/4″ |
| Max Torque | 50 in-lbs (5.65 Nm) |
| Included Accessories | 1 pc USB cable, 44 pcs accessories |
| Accessories Breakdown | 8 pcs Sockets |
1 pc 1” Screw bit holder
1 pc 2-3/8” Screw bit holder
28 pcs 1” Screwdriver bits
6 pcs HSS Drill bits
FUNCTIONAL DESCRIPTION
- Chuck
- Battery Capacity Indicator
- Two Position Adjustment Button
- Forward/Reverse Switch
- On/Off Trigger Switch
- Work Light
OPERATION
CAUTION: The safety instructions should be read carefully before operating the tool.
Power supply:
- Connect one end of the USB cable to the screwdriver and the other end to the usb charging port (such as power band, wall charger, notebook or car charger).
- After 3-5 hours, three indicated lights will turn on, which represents the tool is full charged.
LED Battery Capacity Indicator
The battery capacity is indicated by 3 lights:
- Red LED is on – <20%
- Red & yellow LED’s are on – 20-70%
- Red & yellow& green 3 LED’s are on – >70%
- Once only the red LED is lit, the screwdriver must be re-charged.
Two Position Adjustment
- The driver can be used as one straight driver.
- First press the rotation button, turn the front section in an anticlockwise direction and then release the button when can not turn it again.
- NOTICE: Do not use screwdriver as a pry bar in either position.
- CAUTION: To avoid screwdriver being turned on accidentally, keep switch locked in center position.
Installing/removing bits:
The 1/4” fast load chuck provides fast, easy one-handed bit loading and ejecting.
To install bits:
- Lock forward / neutral / reverse switch on the tool by placing the direction of rotation selector in neutral position. Pull the chuck sleeve away from the driver.
- Push the bit into the chuck, release the chuck sleeve to lock bit into place.
- Pull on the bit to make sure it is secured in the chuck. It’s normal to have a small gap for bit installation.
NOTE: Only use bits with quick connecting locking groove.
To remove bits:
- Lock the trigger by placing the rotation selector in the neutral position.
- With the nose of the tool pointed away from you, pull the chuck sleeve away from the driver. Remove the bit from the chuck.
CAUTION: The screwdriver is not designed to be used as a drill.
Forward/Reverse switch & Trigger lock
For forward rotation, (with chuck pointed away from you) move the lever to the far left. For reverse rotation move the lever to the far right.
To activate trigger lock move lever to the center off position.
Warning: Do not change direction of rotation until the tool comes to a complete stop. Shifting during rotation of the chuck can cause damage to the tool.
MAINTENANCE
This screwdriver does not require special maintenance. The repair of internal parts of the tool should be left with specialists (see safety instructions).
PARTS LIST
| No. | Description | Qty. |
|---|---|---|
| 1 | Motor _ RS380 3.6V | 1 |
| 2 | Motor gear | 1 |
| 3 | P_ 039 _ 08A Gearbox cover | 1 |
| 4 | ISO 7045- M2.5x 5-Z — 5S | 2 |
| 5 | Washer | 1 |
| 6 | Back star gear __ plastic | 3 |
| 7 | Back star gear holder | 1 |
| 8 | Front star gear_ steel | 3 |
| 9 | Ring gear | 1 |
| 10 | Self lock block | 1 |
| 11 | Locking pin | 6 |
| 12 | Self lock ring | 1 |
| 13 | Lock washer | 1 |
| 14 | Self lock core | 1 |
| 15 | Bushing | 1 |
| 16 | Gearbox front | 1 |
| 17 | Pressure pin 3mm | 3 |
| 18 | Output axis | 1 |
| 19 | Pressure washer | 1 |
| 20 | Torque spring | 1 |
| 21 | Screw ring | 1 |
| 22 | P 039 10A Adjusting ring rear | 1 |
| 23 | P_ 039 _ 11A Adjusting ring front | 1 |
| 24 | P _ 039 A03A_ PCB batterybar | 1 |
| 25 | P 039 03A Housing main upside __ left | 1 |
| 26 | P 039 12A_ Index spring | 1 |
| 27 | LED_ 3mm | 1 |
| 28 | P_ 039 01A Housing main handle left | 1 |
| 29 | Compression spring | 2 |
| 30 | Screw DIN 7981 2.2×4.5 | |
| 31 | P-035_ 06A __ Contacts-trigger | 1 |
| 32 | P_ 039 _ 06A _Trigger main | 1 |
| 33 | P_039 _ 07A Switch direction | |
| 34 | Switch SS-23E26(2P3T) Baohui | |
| 35 | P-035 05B PCB | 1 |
| 36 | Li-lon Battery 18650 | 1 |
| 37 | P_ 039 __ 02A Housing main. handle right | 1 |
| 38 | Screw GB845- 1985 2.6×12 | 8 |
| 39 | P_ 039 05A Switch rotation | 1 |
| 40 | P 039 04A Housing main upside_ right | 1 |
FrequentlyAsked Questions
What are the specifications of the AVID POWER ACSD368 Electric Screwdriver?
The AVID POWER ACSD368 operates at a no-load speed of 200 rpm, features a 1/4 inch chuck size, and delivers a maximum torque of 50 in-lbs (5.65 Nm).
How long does it take to charge the AVID POWER ACSD368 Electric Screwdriver?
The screwdriver typically requires 3-5 hours to fully charge.
What safety precautions should I take when using the AVID POWER ACSD368 Electric Screwdriver?
Users should wear appropriate personal protective equipment, work in a well- lit and clean environment, and avoid operating the tool near explosive or flammable materials.
How can I check the battery capacity of the AVID POWER ACSD368 Electric Screwdriver?
The battery capacity is indicated by LED lights, with red indicating less than 20% charge, red and yellow indicating 20-70% charge, and all three colors indicating more than 70% charge.
What accessories are included with the AVID POWER ACSD368 Electric Screwdriver?
The screwdriver comes with 1 USB cable and 44 accessories, including sockets, screwdriver bits, and drill bits.
How do I install and remove bits from the AVID POWER ACSD368 Electric Screwdriver?
Bits can be easily installed and removed using the 1/4 inch fast load chuck, with instructions provided in the operator's manual.
What should I do if my AVID POWER ACSD368 Electric Screwdriver requires maintenance?
The screwdriver does not require special maintenance, but internal repairs should be handled by specialists. Contact the after-sales department for assistance.
Is the AVID POWER ACSD368 Electric Screwdriver suitable for heavy-duty use?
No, this screwdriver is designed for do-it-yourself projects and should not be considered heavy-duty equipment.
Can I use the AVID POWER ACSD368 Electric Screwdriver for professional projects?
While the screwdriver is suitable for DIY projects, it may not be ideal for professional use due to its intended design as a do-it-yourself tool.
What is the battery type of the AVID POWER ACSD368 Electric Screwdriver?
The screwdriver uses a lithium-ion battery pack for power.
Is the AVID POWER ACSD368 Electric Screwdriver lightweight and portable?
Yes, the screwdriver weighs only 2.68 pounds and is compact in size, making it easy to carry and maneuver during use.
Can I use the AVID POWER ACSD368 Electric Screwdriver in dimly lit areas?
Yes, the screwdriver is equipped with a work light to provide illumination in dark or poorly lit workspaces.
Video- Product Overview
Download the PDF:AVID POWER ACSD368 Electric Screwdriver Operating Manual
Reference:AVID POWER ACSD368 Electric Screwdriver Operating Manual- device.report
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>