AVID POWER ‎ACD306 Cordless Drill User Manual

AVID POWER ‎ACD306 Cordless Drill

MODEL:

• ACD306-N/
• ACD306-P

12V CORDLESS DRILL/DRIVER

Operator’s Manual

SAVE THIS MANUAL

• You will need this manual for safety instructions, operating procedures and warranty.
• Put this manual and the original sales receipt in a safe dry place for future reference.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: When using electric tools, machines or equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury. The warnings, cautions, and instructions detailed in this manual cannot cover all possible conditions and situations that occur.

1. KEEP THE WORK AREA CLEAN. Clean areas prevent injuries.
2. CONSIDER THE WORK AREA ENVIRONMENT. Don’t use power tools in damp, wet, or poorly lit locations. Don’t expose your tool to the rain. Keep the work area well lit. Don’t use tools in the presence of flammable gases or liquids.
3. KEEP CHILDREN AWAY. All children should be kept away from the work area. Don’t let them handle machines, tools and extensions cords.
4. STORE UNUSED EQUIPMENT. Store equipment in a dry area to inhibit rust. The equipment also should be in a high location or locked up to keep out of the reach of children.
5. DON’T FORCE THE TOOL. It will do the job better and more safely at the rate for which it was intended.
6. USE THE RIGHT TOOL. Don’t force a small tool or attachment to do the work of a larger industrial tool. Don’t use a tool for a purpose for which it was not intended.
7. DRESS PROPERLY. Don’t wear loose clothing or jewelry, they can get caught in moving parts. Protective, non-electrically conductive gloves and non-skid footwear are recommended when working. Wear protective hair covering to contain long hair and keep it from harm.
8. USE EYE PROTECTION. Use a full face mask if the work you’re doing produces metal filings, dust or wood chips. Goggles are acceptable in other situations. Wear a clean dust mask if the work involves creating a lot of fine or coarse dust.
9. DO NOT TOUCH BITS OR BLADES WITH HANDS AFTER USE. They can become extremely hot after the job is completed.
10. SECURE WORK. Use clamps or a vise to hold the work if possible. It’s safer than using your hands and it frees both hands to operate the tool.
11. DON’T OVERREACH. Keep proper footing and balance at all times. Do not reach over or across machines that are running.
12. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance.
13. Follow instructions for lubricating and safe performance. Follow instructions for lubricating and changing accessories. Keep handles dry, clean and free from oil and grease.
14. REMOVE ALL ADJUSTING KEYS AND WRENCHES. Make it a habit to check that keys and adjusting wrenches are removed from any rotating tool before using it.
15. AVOID UNINTENTIONAL STARTING. Don’t carry tools with a finger on the switch. Be sure the direction switch is in the STOP position when not in use or when changing attachments.
16. STAY ALERT. Watch what you are doing & use common sense. Don’t operate any tool when you are tired.
17. CHECK FOR DAMAGED PARTS.
    • Before using the tool, any part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function.
    • Check for alignment of moving parts, binding of moving parts, breakage of parts, mountings, and other conditions that may affect its operation.
    • Check bits and blades to make sure they are sharp and not chipped. Inspect screws and tighten any ones that are loose.
    • Any part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in the instruction manual. Have defective switches replaced by an authorized service center? Don’t use the tool if the switch does not turn on and off properly.
18. GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces such as pipes, radiators ranges, and refrigerator enclosures. When drilling or cutting into walls, floors, or wherever “live” electrical wires may be, try to ascertain whether there is a danger of shock.
19. REPLACEMENT PARTS. When servicing, use only identical replacement parts.

PRECAUTIONS FOR BATTERY CHARGER

CHARGE BATTERY AT LEAST 6 HOURS before initial use.

1. CHARGE AT ROOM TEMPERATURE. The room temperature must be higher than 32°F and lower than 104°F.
2. DO NOT CHARGE IF THE CHARGER’S CORD OR PLUG IS DAMAGED. Charging with a damaged cord may result in a fire or electrical shock. If the charger is damaged in any way, have it repaired by a qualified serviceman.
3. USE WITH CAUTION, when coming into contact with items that can cause an electrical short, such as paper clips, nails, the sides of a metal toolbox.
4. DO NOT INCINERATE THE BATTERY. This product has been carefully engineered and manufactured to give you dependable operation. Please read this manual thoroughly before operating your new product, as it contains the information you need to become familiar with its features and obtain the performance that will bring you continued use for many years.

SAFETY PRECAUTIONS FOR 12V DRILL

1. Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.
2. Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring.
3. Special Safety Instructions for Battery Pack and Charger. If under extreme conditions any electrolyte should escape from the battery, it’s essential to avoid contact with skin. If electrolyte does come into contact with your skin, rinse it off with water. In the event of electrolyte contact with your eyes, it’s essential to consult a doctor.
4. Before the use of the charger and the battery pack, read the instruction manual for it carefully.
5. During the charging process, the current used should correspond to the current of the battery charger.
6. Never let moisture, rain or splashed water reach the charging location. The ambient temperature must not exceed 40℃.
7. Battery packs, which are defective or damaged or can no longer be recharged, must be disposed of as hazardous waste. Hand them over at a special collection point. Never harm our environment. Do not throw unusable battery pack away into the domestic waste, into fire or into water.
8. If the electrical cable is damaged, the wire may only be replaced by the supplier or by his repair workshop. Have repairs carried out only by an authorized specialist.
9. Use only the battery pack, which has been produced by the original manufacturer.
10. Always keep the surface of the charger free from dust and dirt.
11. Insert the battery pack into the charger. Follow the guidelines provided concerning polarity.
12. Always remove battery pack before working on the machine.
13. When the battery pack is outside the drill, cover the contacts to avoid short circuits (e.g. from tools).
14. Do not throw Li-ion batteries into water or fire, risk of explosion!
15. Protect the battery pack from impacts, and don’t open it.
16. Never discharge the battery pack completely and recharge occasionally if not used for a prolonged period.

PRODUCT SPECIFICATION

TOOL COMPONENTS

• 1. Keyless chuck
• 2. Torque settings
• 3. Variable speed trigger switch
• 4. Trigger lock
• 5. Build in work light
• 6. Gear shifter
• 7. Rubberized grip
• 8. Battery pack
• 9. Battery release tags

PACKAGE INCLUDED

• A. Charger
• B. Charger stand
• C. Flexible shaft
• D. Extended bar
• E. 10pcs drill bits
• F. 10pcs driver bit

OPERATION

How to install/remove the battery pack

1. Release battery pack from tool by pressing on both sides of the battery release tabs and pull downward (Fig.2).
2. To insert battery, align battery and slide battery pack into tool until it locks into position. Do not force.

(Note: If battery release tabs are cracked or damaged, do not insert into tool. Battery can fall out during operation.)

• 1. Cordless drill
• 2. Battery pack
• 3. Release button

CAUTION

• Fully charge battery before first use. The battery will reach full capacity after being charged and discharged several times.
• Avoid short periods of charging. Only charge the battery pack when completely empty.
• Adaptor, charger and battery pack will be warm when charging.

How to charge the battery pack (Fig.3)

1. Insert the AC/DC adaptor into the household current receptacle. The green light is on. The green light is the power indicator.
2. Properly insert the battery pack into the charging stand. Make sure it is placed correctly(+ and -). The red light is on. The red light is the charge indicator.
3. Normal charging time is 3-5 hours. When the battery is fully charged, the red light will turn off.
4. When charging more than one battery pack in succession, allow 15 minutes between charges.

METHOD 1 (Fig.4)

To install the driver bit/drill bit:

• Step 1: Rotate the chuck (A) anticlockwise by hand to open the chuck jaws. (If A was screwed too tight, please rotate it with more force).
• Step 2: Place the driver/drill bit in the chuck as far as it will go.
• Step 3: Then rotate the chuck (A) clockwise by hand to tighten the chuck jaws.

Do it in reverse to remove the driver bit/drill bit.

METHOD 2（Fig.5 Fig.6 Fig.7）

• To install the driver bit/drill bit:

• Step 1: Open the chuck jaws: move the forward/reverse button to the right side of the tool to make it do reverse rotation.

• Step 2: Hold the keyless chuck with one hand and squeeze the trigger with the other hand to open the chuck jaws.

• Step 3: Carefully center the driver bit/drill bit between the jaws.

• Step 4: Move the forward/reverse button to the left side, it will do forward rotation.

• Step 5: Hold the keyless chuck with one hand and squeeze the trigger slowly until it is locked in place.

• Do it in reverse to remove the driver bit/drill bit.

NOTE: This drill is compatible with the accessories of other brands. However, since the drill chuck is 3/8 inch, the diameter of drill bits/driver bits you purchase cannot exceed 3/8 inch.

ADJUSTMENT

REVERSING SWITCH (Fig.8)

• The reversing switch determines the rotational direction of the tool and also serves as a lock-off button. You can choose between clockwise and anticlockwise rotation. To avoid causing damage to the gearing it is advisable to change the direction of rotation only when the tool is at a standstill.
• To select forward rotation, release the trigger switch and depress the forward/reverse control button on the right side of the tool.
• To select reverse rotation, depress the forward/reverse control button on the left side of the tool.

NOTE: The first time the tool is run after changing the direction of rotation, you may hear a click on start up. This and the impacting noise that the tool makes is normal and does not indicate a problem.

GEAR SHIFTING (Fig.9)

The tool is equipped with two separate gear ranges, low gear, and high gear. Low gear provides high-torque and slower drilling speeds for heavy-duty work or for driving screws. High gear provides faster speeds for drilling lighter work.

• Select LOW speed for applications requiring higher power and torque.
• Select HIGH speed for fast drilling, drilling or driving applications.

NOTE

• Never change speeds while the tool is running. Failure to obey this caution could result in serious damage to the drill.
• If you have difficulty changing from one gear range to the other, turn the chuck by hand until the gears engage.

Torque adjustment collar(Fig.1)

The torque can be adjusted in 0-15 graduation by turning the adjusting collar. Circling the collar are numbers and a drill bit symbol. These numbers are used to set the clutch to deliver a torque range. The higher the number on the collar, the higher the torque and the larger the fastener which can be driven. To select any of the numbers, rotate until the desired number aligns with the arrow.

NOTE: Before the actual operation, drive a trial screw into your material or a piece of duplicate material to determine which torque level is required for a particular application.

Trigger Switch (Fig.10)

To turn the tool on, squeeze the trigger switch . To turn the tool off, release the trigger switch. The chuck will stop as soon as the trigger switch is fully released. The variable speed switch enables you to select the best speed for a particular application. The more you squeeze the trigger, the faster the tool will operate. Use lower speeds for starting holes without a center punch, drilling in metals or plastics, or driving screws. For maximum tool life, use variable speed only for starting holes or fasteners.

MAINTENANCE

ATTENTION: Always remove the battery before carrying out any work on the machine.

• To clean, always use a dry or moist, but not wet towel. Many cleaning agents contain chemical substances which may cause damage to the plastic parts of the machine. Therefore do not use any strong or flammable cleaners such as gas, paint thinner, turpentine or similar cleaning agents.
• Always keep air ventilation holes free of dust deposits to prevent overheating.
• Keep the vents clear of dust and debris. This will help prevent possible electrical shorts and ensure proper cooling.
• Keep the tool housing and handle clean and free of oil and grease by using mild soap and a damp (not wet) cloth.
• Avoid overloading your drill. It will become hot and lose efficiency. Running it free of load for a minute or two will allow it to cool itself to normal temperature. 6. Inspect the cord regularly and have it replaced by an authorized repair facility if it is damaged.
• Lubrication for this tool is done at the factory and should not be necessary again under normal use.
• An authorized repair center should do any repairs, modification, or maintenance that involves disassembling the grinder.
• Any damage to the tool should be corrected at an authorized repair center.

PART LIST

SCHEMATIC DRAWING

FrequentlyAsked Questions

How does the AVID POWER ACD306 Cordless Drill compare to other models in its category?

The AVID POWER ACD306 Cordless Drill stands out with its 12V power, adjustable torque settings, and keyless chuck. Its lightweight design and comprehensive package make it a popular choice among DIY enthusiasts and professionals alike.

What safety features does the AVID POWER ACD306 Cordless Drill offer?

The AVID POWER ACD306 Cordless Drill prioritizes safety with features like a trigger lock, forward/reverse switch, and torque adjustment collar. Additionally, its ergonomic design and rubberized grip enhance user comfort and control during operation.

Can the AVID POWER ACD306 Cordless Drill be used for heavy-duty tasks?

While the AVID POWER ACD306 Cordless Drill is suitable for a wide range of drilling and driving applications, it may not be ideal for heavy-duty tasks. Users should adhere to recommended usage guidelines to prevent overloading the tool.

How long does it take to charge the battery pack of the AVID POWER ACD306 Cordless Drill?

The battery pack of the AVID POWER ACD306 Cordless Drill typically requires 3-5 hours for a full charge. It's essential to follow the charging instructions provided in the manual for optimal performance and battery life.

What should I do if the battery pack of the AVID POWER ACD306 Cordless Drill appears damaged or leaks?

In case of battery damage or leakage, avoid contact with the electrolyte and follow the provided instructions for safe handling. Dispose of damaged batteries properly and replace them with new ones to ensure safe operation.

Can I use accessories from other brands with the AVID POWER ACD306 Cordless Drill?

While the AVID POWER ACD306 Cordless Drill is compatible with accessories from other brands, it's recommended to use accessories recommended by AVID POWER for optimal performance and safety.

How does the torque adjustment collar work on the AVID POWER ACD306 Cordless Drill?

The torque adjustment collar allows users to adjust the torque output for different applications. By selecting the appropriate torque setting, users can prevent over-tightening or stripping of screws, ensuring precise and efficient drilling and driving.

How should I maintain the AVID POWER ACD306 Cordless Drill for optimal performance?

Regular maintenance of the AVID POWER ACD306 Cordless Drill includes keeping it clean, lubricated, and free from debris. Follow the maintenance instructions provided in the manual for longevity and reliability.

Is the AVID POWER ACD306 Cordless Drill suitable for prolonged use?

While the AVID POWER ACD306 Cordless Drill offers cordless convenience, it's recommended not to use it continuously for more than 20 minutes at a time to prevent overheating and ensure optimal performance.

How does the battery life of the AVID POWER ACD306 Cordless Drill compare to other models?

With its 12V 1.3 Ah battery, the AVID POWER ACD306 Cordless Drill offers sufficient power and runtime for most drilling and driving tasks. Battery life may vary depending on usage patterns and operating conditions.

What sets the AVID POWER ACD306 Cordless Drill apart from its competitors?

The AVID POWER ACD306 Cordless Drill distinguishes itself with its ergonomic design, adjustable torque settings, and comprehensive package of accessories. Its affordability and reliability make it a top choice for both beginners and experienced users.

Can I use the AVID POWER ACD306 Cordless Drill for drilling into different materials?

Yes, the AVID POWER ACD306 Cordless Drill is suitable for drilling into various materials, including wood, metal, plastic, and more. Users can adjust the torque settings for optimal performance based on the material being drilled.

Video- How to Open/Close the Drill Chuck?

Download the PDF:AVID POWER ‎ACD306 Cordless Drill User Manual

Reference:AVID POWER ‎ACD306 Cordless Drill User Manual- device.report

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>