G MADE GS02F TS Chassis Kit Installation Guide
- May 15, 2024
- G MADE
Table of Contents
CAUTIONS
**** In order to avoid personal injury or property damage, you have to act in
a responsible manner and follow these directions.
RC models can operate at over 40Km/h but can not stop immediatety
Safety Precautions
– Check the surrounding area before you operate RC model.
– Choose a good place to operate your RC model
– Do not operate your RC mode! on the street or highway. It can cause a
serious damage or a serious accident.
– Do not operate your RC model in confined or crowded areas, in order to avoid
accident.
– Never operate your RC model near peopie or animals, and never use people or
animais as an obstacle.
– A collision between your RC model and stationary objects can cause damage to
either
– Do not operate your RC model in public places like hospital and residential
areas. It can cause great noise
– Never operate your RC model indoor. There is a higher possibility of fire or
damage
Safety Precautions (Before assembling)
– Before you start assembling this model, read the instructions carefully and
make sure you understand them
thoroughly.
– If a child assembies this model, an adult must also read the instructions
carefully and understand them thoroughly.
– Always be careful when using tools like knives. Extra care should be taken
to prevent injuries.
– If you use paint or cement (not included in the RC model), read the
instructions supplied with them.
– Keep the parts out of reach of children, smail parts can cause choking and
viny! bags can suffocate.
Safety Precautions (Before you operate RC model, check the following.)
– Check to ensure nuts bolts are tightened appropriately.
– Check that no one else is using your radio frequency.
– Use new batteries to avoid losing control of the transmitter and receiver.
– You will need a 2 channel radio system which includes a servo, a receiver,
an ON/OFF switch, and an electronic speed control.
– Be sure to use a radio frequency for ground model — Do not use airplane
frequencies.
– Always check the brakes and throttle before you operate your RC model, in
order to avoid losing control of the model.
– To prevent unexpected movements of your RC model, do not connect the
batteries to receiver before turning on the transmitter.
– Always tum on the transmitter first, and then connect the batteries to the
receiver.
1. Switch on the transmitter.
2. Check that the speed control, the transmitter control, and trims are set
to the neutral position.
3. Connect the RC model to the receiver’s batteries.
4. Switch on the model and the receiver.
– When you using rechargeable batteries, make sure you read and follow the
instructions carefully.
– Inappropriate handling or usage of rechargeable batteries can cause serious
injuries or accidents.
Cautions While Operating
– When the RC model is operating, do not touch the moving parts like the drive
shaft and wheels.
– The moving parts can cause serious injuries.
– Always tum the model or receiver off and disconnect the batteries before
turing off the transmitter, in order to avoid unexpected movements of your RC
model.
1. Tum off the model or receiver.
2. Disconnect the batteries.
3. Turn off the transmitter.
– Do not touch the vehicle’s speed control resistor while operating of the RC
model. The resistor may be very hot, especially after running at lower speeds.
– To prevent damage to the RC model, remove the battertes from the model and
transmitter when you don’t intend to run the RC model for some time.
– After operating your RC model, batteries become hot, so please be careful
when handling.
– In order to prolong the life of your RC model, please keep it free from din
and grease.
– Before you start assembling this model, read the instruction carefully and
make sure you understand them fully.
– If a child assembies this model, an adult must also read the instructions
carefully and understand them thoroughly.
EQUIPMENT NEEDED
OVERDRIVE GEAR RATIO
No overdrive (Option)
30T / 30T (GM30172)
| Pinion | Drive | LO | HI |
|---|---|---|---|
| 9T | Front | 66.85 | 31.67 |
| Rear | 66.85 | 31.67 | |
| 10T | Front | 60.17 | 28.50 |
| Rear | 60.17 | 28.50 | |
| 11T | Front | 54.70 | 25.91 |
| Rear | 54.70 | 25.91 | |
| 12T | Front | 50.14 | 23.75 |
| Rear | 50.14 | 23.75 | |
| 13T | Front | 46.28 | 21.92 |
| Rear | 46.28 | 21.92 | |
| 14T | Front | 42.98 | 20.36 |
| Rear | 42.98 | 20.36 | |
| 15T | Front | 40.11 | 19.00 |
| Rear | 40.11 | 19.00 |
Overdrive percentage: 0%
Overdrive 1 (Stock)
32T / 28T
| Pinion | Drive | LO | HI |
|---|---|---|---|
| 9T | Front | 58.50 | 27.71 |
| Rear | 66.85 | 31.67 | |
| 10T | Front | 52.85 | 24.94 |
| Rear | 60.17 | 28.50 | |
| 11T | Front | 47.86 | 22.67 |
| Rear | 54.70 | 25.91 | |
| 12T | Front | 43.87 | 20.78 |
| Rear | 50.14 | 23.75 | |
| 13T | Front | 40.50 | 19.18 |
| Rear | 46.28 | 21.92 | |
| 14T | Front | 37.60 | 17.81 |
| Rear | 42.98 | 20.36 | |
| 15T | Front | 35.10 | 16.63 |
| Rear | 40.11 | 19.00 |
Overdrive percentage: 14.29%
Overdrive 2 (Option)
33T / 27T (GM30168)
| Pinion | Drive | LO | HI |
|---|---|---|---|
| 9T | Front | 54.70 | 25.91 |
| Rear | 66.85 | 31.67 | |
| 10T | Front | 49.23 | 23.32 |
| Rear | 60.17 | 28.50 | |
| 11T | Front | 44.75 | 21.20 |
| Rear | 54.70 | 25.91 | |
| 12T | Front | 41.02 | 19.43 |
| Rear | 50.14 | 23.75 | |
| 13T | Front | 37.87 | 17.94 |
| Rear | 46.28 | 21.92 | |
| 14T | Front | 35.16 | 16.66 |
| Rear | 42.98 | 20.36 | |
| 15T | Front | 32.82 | 15.55 |
| Rear | 40.11 | 19.00 |
Overdrive percentage: 22.22%
BATTERY LOCATION
SPARE PARTS LIST
| PART# | PRODUCT NAME |
|---|---|
| GM60061 | GAA4 front axle housing parts tree |
| GM60064 | GA44 axie hardware set |
| GM60063 | GA44 axte parts tree |
| GM60023 | 5.8mm bail parts tree |
| GM60062 | GA44 rear axle housing parts tree |
| GM60068 | 33T bevel gear |
| GM60067 | 11T bevel gear |
| GMA0165 | Ball bearing 5x11x4mm |
| GMA0205 | Ball bearing 8x12x3.5mm |
| GMA0167 | Ball bearing 10x15x4mm |
| GM60111 | Input universal joint set |
| GM60109 | GA44 CVA kit |
| GM60102 | CVA drive coupter (2) |
| GM60112 | Straight drive shaft 107mm (2) |
| GM60065 | Pin 2×11.4mm (4) |
| GM60110 | CVA pin retaining ring (2) |
| GM60099 | Panhard rod 86mm |
| GM60100 | GA44 steering rod set |
| GM51603 | Pin 2×10.3mm (4) |
| GM60220 | GS02F transmission housing parts tree |
| GM60221 | GS02F inner fender braces & transmission hardware parts tree |
| GM60080A | 32P 45T Spur gear |
| GM60071 | 48P 38T 1st gear (LO) |
| GM60069 | 48P 18T gear |
| GM60210 | 48P 28T 2nd gear (HI) |
| GM60212 | 48P 32T gear |
| GM60072 | 32P 13T pinion gear |
| GM60211 | HI/LO sliding clutch |
| GM60213 | Transmission output front shaft 5.3mm |
| GM60214 | Transmission output rear shaft 63.14mm |
| GM60215 | Transmission shaft 117.9mm |
| GM60216 | Stipper shaft 37.8mm |
| GM60217 | Transmission fork shaft 49.2mm |
| GM60033 | Pin 1.5×7.2mm (4) |
| GM60088 | Slipper pad (2) |
| GM60087 | Slipper disk 20×1.5mm (2) |
| GMA0163 | Ball bearing 5x8x2.5mm |
| GM60022 | M4 5.8mm rod end set |
| GM60089 | Upper link M4x6.8x55mm (2) |
| GM60222 | Lower link M4x6.8x78mm (2) |
| GM60092 | Lower link M4x6.8x100mm (2) |
| GM60091 | Upper link M4x6.8x98mm (2) |
| GM60081 | GS02 frame side rails |
| GM60078 | GS02 battery tray & cross member parts tree |
| GM60219 | GSO02F skid plate & battery tray parts tree |
| GM60001 | 16.5mm servo saver parts tree |
| GM60076 | GS02 side plate parts tree |
| GM60077 | GS02 shock hoop & body post parts tree |
| GM60117 | Veicro strap 16x220mm (2) |
| GM60104 | Foam seal (2) |
| GMA0213 | S56 O-ring |
| GM60218 | GS02F front & rear inner fenders |
| GM0020078 | RSD shock delrin pistons (2) |
| GM60079 | SD shock parts tree |
| GM60094 | SD 90mm shock body (2) |
| GMA0169 | P3 O-ring |
| GMA0160 | 2mm E-ring |
| GMA0212 | 7×1 O-ring |
| GM0020075 | Shock shaft 3.5×46.4mm |
| GM60097 | Shock spring 15.2×6 1mm (2) |
| GM60084 | Universal shaft parts tree |
| GM60101 | Universal joint set |
| GM60119 | Universal joint drive coupler (2) |
| GM60093 | 5.8mm bail stud M3x5mm (5) |
| GM60226 | Servo saver spring 9×9.5mm |
| GMA0170 | P5 O-ring |
| GM50116 | R6 snap pin (12) |
| GMA0161 | 2.5mm E-ring |
| GMA0162 | 4mm E-ring |
| GMA0210 | 4mm conical spring washer |
| GMA0158 | 3mm washer |
| GMA0154 | M3 nut |
| GMA0156 | M3 nylon lock nut |
| GMA0191 | M3 flange nut |
| GMA0157 | M4 nyton lock nut |
| GMAO0011 | 2.5x6mm round head wrench bolt |
| GMA0017 | 3x6mm round head wrench bolt |
| GMA0018 | 3x8mm round head wrench bolt |
| GMA0019 | 3x10mm round head wrench bolt |
| GMA0020 | 3x12mm round head wrench bolt |
| GMA0021 | 3x15mm round head wrench bolt |
| GMA0172 | 3x18mm round head wrench bolt |
| GMA0022 | 3x20mm round head wrench bolt |
| GMA0023 | 3x25mm round head wrench bolt |
| GMA0024 | 3x30mm round head wrench bolt |
| GMA0082 | 2x6mm wrench bolt |
| GMA0093 | 2.5x8mm wrench bolt |
| GMA0094 | 2.5x10mm wrench bolt |
| GMA0095 | 2.5x12mm wrench bolt |
| GMA0102 | 3x8mm wrench bolt |
| GMA0104 | 3x12mm wrench boit |
| GMA0106 | 3x18mm wrench boit |
| GMA0107 | 3x20mm wrench bott |
| GMA0108 | 3x25mm wrench bolt |
| GMA0109 | 3x30mm wrench boit |
| GMA0126 | 3x3mm socket set screw |
| GMA0127 | 3x4mm socket set screw |
| GMA0132 | 3x12mm socket set screw |
| GMA0131 | 3x10mm socket set screw |
| GMA0144 | 4x15mm socket set screw |
| GMA0145 | 4x20mm socket set screw |
| GM60103 | 3x10mm Screw pin (4) |
| GMA0056 | 3x6mm fiat head wrench bolt |
| GMA0057 | 3x8mm flat head wrench bott |
| GMAO00S8 | 3x10mm flat head wrench bolt |
| GMA0059 | 3x12mm flat head wrench bolt |
| GMA0060 | 3x15mm flat head wrench bolt |
| GMA0064 | 3x35mm flat head wrench bolt |
Address : GMADE Building, Gonghang-dong 61-134, Gangseo-gu, Seoul 07627, South
Korea
Tel : 02-2696-8170
Fax : 02-2696-8171
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>